FeiYu Tech G4S Beginner's Manual
ON
OFF
ON
OFF
V
C
C
V
18350
18350
MINI-USB
10Pin
1
2
3
4
Joystick
360°
360°
360°
360°
For other functions
Switch operating modes
Turn on/off
The working mode and
function can be identified
by the LED status
Joystick
Joystick
Video Output Cable
5
Read the GoPro SD card and Charge the GoPro
PC
GoPro Mini
Video / SD
to Micro port
reading switch
GoPro charging
switch
USB Cable
Read the GoPro SD card and
charge the GoPro without dismount
the GoPro
When the gimbal and GoPro are
powered on , connect the Analog
Monitor to the function port with
the Video Output Cable, to output
the video to the Analog Monitor.
G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can read the GoPro SD card and
Charge the GoPro without dismount the GoPro, and it works when the gimbal is powered off.
The GoPro charging switch and the SD card reading switch works independently, and it works when the gimbal is powered off. The default is off.
Rolling
Rolling
Tilting
Tilting
Panning
Panning
Function Button
（ ON / OFF ）
1/4 Inch Screw Hole
EN
If the indicator light flashes red, the
Gimbal will not work correctly due to
Attention !
an error.
1
Beginner Guide
2
Product Appearance Instructions
4
Video Output
Operation Instructions
3
Inversion Mode
When in any working mode, press the function button
for three times in succession, the Gimbal will enter into the inversion mode
and switch to the Panning Mode automatically.
Invert the Gimbal to capture more excited scenes easily by switching mode
combination. When in inversion working condition press the function button
for three times in succession to reset the Gimbal back to the original state.
Reset
Indicator Explanation
LED Status
Explain
Blue light flashes
three times
Full Power
Blue light flashes
twice
Enough Power
Blue light flashes
once
Low Power
Blue light keeps
flashing
No Power
If any comments or suggestions please do not hesitate
Remove the power switch
cap, insert two 18350
batteries into the handle.
to e-mail us directly : service@feiyu-tech.com
Mount the camera carefully to
the mounting bracket and make
sure the camera is firmly connected
with the MINI-USB 10Pin.
Press the clip at both ends of the
clip, clip it as above picture.
Power On / Off
Assembly the clip
Mount the Camera
Insert The Batteries
Joystick
You can control
the direction by
the joystick
Function
Interface
Indicator
Working Mode Instructions
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Panning Mode
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Panning and Tilting Mode
Lock Mode
Function
Interface
Analog Monitor
( Equipped By Users )
Function Button
( Indicator Light )
Version 2.0
Applicable to the firmware V1.25 and above version
Power On: Single tap the function button,the
gimbal shall be powered on after 2 seconds.
Power Off: Hold down the function button for
3 seconds to turn off the gimbal.
Attention: Turn the gimbal on
after ensuring the camera is secure.
Operation
Double tap
Reset the tilting axis of the gimbal to initial orientation and initial mode
Function
Single tap
Explanation
Panning Mode / Lock Mode
Panning and Tilting Mode
Triple tap
Single tap to switch between panning mode and lock mode
Under panning and tilting mode, single tap to switch to lock mode
Inversion Mode
It is possible to switch to other modes under inversion mode,
triple tap again to exit inversion mode and reset
Long press for 3 seconds
Power off
Quadruple tap
Reset
Tap button for six times
Please refer to“Gimbal Horizontal Angle Adjustment”for operations
Single tap again to awake the gimbal, or triple tap
to initialize the gimbal
Rolling angle adjustment
Long press for 1 second
Standby
LED Status
Mode / Status
Single flash
Double flashes
Panning mode
Panning and Tilting mode
Lock mode / Initialize the gimbal
Always on
Flash quickly
Rolling angle adjustment /
Initialization failure / Malfunction
Three flashes
Indicator
Standby
Operating Instructions of Function Button
Light
Status
Reset the tilting axis of the gimbal to initial orientation
and initial mode.
In standby model, keep the gimbal in power-up state,
the motor stops working, the indicator light flashes for
three times, and single tap again to wake the gimbal.
Standby
Other Function
!
( 1 ) Please install the suitable camera first before power on the Gimbal.
( 2 ) Please turn off the power when not in use.
GND
Video
UP
Down
Left
Up
Down
Left
Right
Right
Joystick
Direction
Joystick Control
micro port
Suitable for GoPro HERO 4 / HERO 3+ / HERO 3
G4S 3-Axis Handheld Gimbal