Operating instructions and parts list instructions d’utilisation et liste de piÈces instrucciones de operaciÓn y lista de piezas tm-75 tile saw 17400 west 119th street olathe, kansas 66061 customer service ......800-365-4003 corp. Office ...............913-928-1000 cust. Service fax......800-825-002...
2 every machine is thoroughly tested before leaving the factory. Each machine is supplied with a copy of this manual. Operators of this equipment must read and be familiar with the safety warnings. Failure to obey warnings may result in injury or death. Follow instructions strictly to ensure long se...
3 symbols definitions symboles definición de simbolos • please read the instructions for use prior to operating the machine for the first time. • avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. • antes de la puesta en marcha, lea detenidamente las instru...
4 • wear appropriate clothing • port obligatoire de la tenue appropriée • usar ropa adecuada • machinery hazard, keep hands and feet clear • danger! Rester à distance de la machine • máquina peligrosa - mantenga manos y pies alejados de la máquina • no non-working personnel in area • zone interdite ...
5 decal descriptions & location autocollants – descriptions et emplacements descriptiÓn de calcamonias y ubicaciones p/n 185262 location: tray - front p/n 169866 location: rip guide p/n 185263 location: motor cover - front p/n 185264 location: blade guard - side p/n 189247 location: motor cover - re...
6 reference figures figures de rÉfÉrence figura de referencia fig 1 fig 2 fig 3 fig 4 fig 5 fig 6 fig 7 fig 8 fig 9 fig 10 fig 11 fig 12.
7 reference figures figures de rÉfÉrence figura de referencia fig 13 fig 14 fig 15 fig 16 fig 17 fig 18 fig 19 fig 20 fig 21 fig 22 187076 90° adjustable protractor fig 23 187077 dual 45 ° angle guide fig 24 187078 bull nose miter guide.
8 safety first! Warnings do’s and do not’s warning: failure to comply with these warnings and operating instructions could result in death or serious bodily injury. Do do read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. Do keep al...
9 safety first! Warnings do’s and do nots warning: failure to comply with these warnings and operating instructions could result in death or serious bodily injury. Do not do not operate this machine unless you have read and understood this operator’s manual. Do not operate this machine without the b...
10 mandatory indication information instruction warning prohibition these signs will give advise for your safety before leaving our factory every machine is thoroughly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions. 1. Features use...
11 3. Machine set-up follow all of the assembly and installation instructions completely before connecting this saw to a power source. Unpacking (fig’s. 1, 2 & 3) carefully open the container and remove all the saw components and packing materials. Be certain you have checked each item with the chec...
12 make sure that the supporting surfaces of the blade, the flanges and the arbor are clean. Electrical connections • use a grounded circuit. • use a gfci when wet sawing. • use the correct plug and outlet. • check that the main voltage is identical to that of the machine. • extension cord: use the ...
13 water tubing removal (fig’s 10, 11) plastic tubing connects the water pump to the blade guard. The fittings used to connect this tubing seal and grip the outside diameter of the tubing. Special internal locking fingers attached to the flanged collet hold the tubing fast. To clean the water tubing...
14 6. Maintenance before performing any maintenance, always place the machine on a level surface with the motor off and disconnect the electrical current. Let the machine cool down!! For longest life and best performance • always clean the saw after every use. • wipe all of the exterior sediment or ...
15 7. Trouble shooting guide saw won’t start, saw is too slow to start, saw motor makes humming noise • make sure plug is in live electrical circuit. • voltage from source may be too low. Saw shuts off abruptly • power is interrupted, check power source and restart the saw. • voltage from source may...
16 diagram 1.
17 diagram 1 --- tm-75 parts list loc p/n description qty loc p/n description qty 1 185108 frame assy (incl. 2-8) 1 53 185243 assy, blade guard (incl. 54-61) 1 2 185106 frame 1 54 185241 guard, blade 8in - machined 1 3 185107 bar, roller guide 1 55 185150 adaptor - y water tube 1 4 185159 clamp, rol...
18 notes:.
19 felker’s new equipment warranty except as noted below. Felker warrants that its new equipment will be free from manufacturing defects for a period of two (2) years from date of purchase by the original consumer purchaser. The above warranty is subject to the following new equipment exceptions: 1....
Felker corporate office 17400 west 119th street olathe, kansas 66061 customer service ..................800-365-4003 corporate office ....................913-928-1000 customer service fax ..........800-825-0028 corporate office fax ............913-438-7951 customer service, int’l...........913-928-1...
