Fellowes POWERSHRED 425Ci Instruction Manual - page 4
4
SET-UP AND TESTING
AUTO
C-485
Ci
AUTO
C-485
Ci
2
4
1
AUTO
C-485
Ci
3
AUTO
C-485
Ci
3
AUTO
C-485
Ci
WHEN IN SLEEP MODE
1
In sleep mode
To get out of sleep mode
touch control panel
insert paper
or
2
CLEANING AUTO-START INFRARED SENSORS
PRODUCT MAINTENANCE
Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the sensors may become blocked by paper dust causing the motor to run
even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry.)
TO CLEAN THE SENSORS
Turn off and unplug
shredder
Lift CD flap
Locate Auto-start
infrared sensor
Dip cotton swab in
rubbing alcohol
Using cotton swab, wipe
away any contamination
from the paper sensors
4
C-485
C
3
C-485
C
5
1
AUTO
C-485
C
2
REFILLING THE OIL
Low oil indicator will
signal when your reservoir
needs refilling
To maintain shredder
performance, refill oil
reservoir with up to 12
oz. (355 ml.) of shredder
oil (Fellowes 35250)
Once refilled, automatic
oiling will resume
• All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and
could ultimately stop running. We recommend that you refill the Auto Oil
TM
reservoir as instructed for optimum performance.
• If shipping shredder, oil must be drained. Open cabinet door and remove basket to access oil drain plug. Place suitable container under drain,
remove plug and let oil drain out. Replace plug.
AUTO OIL
TM
Automatically oils the cutters to enhance performance and extend shredder life.
(Auto oil system is only included on cross-cut models - 425Ci and 485Ci)
AUTO
C-485
C
2
1
ENGLISH
Models 425Ci/425i/485Ci/485i
AUTO
C-485
Ci
3
ADVANCED PRODUCT FEATURES
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
For more information about all of Fellowes Advanced Product Features go to
www.fellowes.com
ENERGY SAVINGS SYSTEM
• Saves energy in four ways: energy-efficient electronics, jam prevention,
standby mode and sleep mode.
• Sleep Mode shuts down shredder after 2 minutes of inactivity.
Optimal energy efficiency 100% of
the time – in use and out of use.
Turn the shredder ON
( ) to activate
SafeSense
®
Touch test area and
look for the SafeSense
®
indicator to illuminate
SafeSense
®
is active and
working properly
If hand is held on SafeSense
®
area more than 3 seconds
shredder will shut off
3
AUTO OIL™ OPERATION
AUTO
C-485
C
1
Press the auto and forward
buttons at the same time for
3 seconds to manually oil
shredder
Before using, fill oil reservoir
with 12 oz. (355 ml.) of
Fellowes shredder oil
To maintain shredder
performance, refill oil
reservoir with up to 12 oz.
(355 ml.) of shredder oil
(Fellowes #35250)
Low oil indicator will
signal when your
reservoir needs refilling
Once refilled, automatic
oiling will resume
SET-UP AND TESTING
REFILLING OIL
1
AUTO
C-485
C
2
Lubricates the cutters automatically to enhance performance and extend shredder life
(Auto oil system is only included on cross-cut models - 425Ci and 485Ci.)
AUTO
C-485
C
2
AUTO
AUTO
Eliminates paper jams and powers through tough jobs.
JAM PROOF SYSTEM OPERATION*
*100% Jam Proof when used in accordance with user manual
STRAIGHT FEED
Advanced Jam Prevention- Electronically
measures paper thickness to prevent paper jams:
Remove several sheets until
indicator is below red.
Continue 100% Jam
Proof Shredding
If a misfeed
occurs:
If
illuminates after paper has been
reversed, press reverse and remove paper.
Otherwise, regular shredding will resume.
1
2
3
Up to RED: Too many
sheets have been inserted.
Up to GREEN: More sheets
can be added.
Up to YELLOW: Productivity
is optimized.
All indicators light up and
shredder pauses for 3-6 seconds
Wait for flashing to stop after automatic correction
is complete. Regular shredding will resume.
If Straight Feed indicator
illuminates, remove paper and
feed straight into shredder.
BASIC SHREDDING OPERATION
Press ( ) ON/OFF
to activate (blue)
Feed paper into paper
entry and release
Plug in and put
disconnect power
switch in ON (I) position
Feed CD, credit card
or junk mail into
designated entry
and release
or
Set to Off ( ) or
shredder will automatically
go into sleep mode after 2
minutes of inactivity
5
1
AUTO
C-485
Ci
AUTO
C-485
Ci
3
4
2
ADVANCED PRODUCT FEATURES
AUTO
C-485
Ci
3
Auto Oil
TM
Lubricates the cutters
automatically to
enhance performance
and extend shredder life.
SafeSense
®
Technology
Stops shredding
immediately when hands
touch the paper opening.
Jam Proof System
Eliminates paper jams
and powers through
tough jobs.
Energy Savings System
Optimal energy efficiency 100%
of the time – in use and out
of use.