1. DL manuals
  2. Fellowes
  3. Laminator
  4. Voyager 125
  5. User Manual

Fellowes Voyager 125 User Manual - Voyager Laminator

Other manuals for Voyager 125: Instructions Manual
Manual is about: High-Performance Office Laminator

Summary of Voyager 125

  • Page 1

    Erformance office laminator high-performance of voyager 125 tm e f s please read these instructions before use. Lire ces instructions avant utilisation. Lea estas instrucciones antes del usarlo. Http://www.Monomachines.Com/ http://www.Monomachines.Com/.

  • Page 2: Voyager Laminator

    Voyager laminator lcd display left (-) right (+) up down standby reverse 5 sec autolam - automatic lamination manual lamination 30 min z z z z z z 30 min easy-access locking screw attention: attention: atenciÓn: top cover locking screw must be la vis de verrouillage du cou- antes de abrir esta maqui...

  • Page 3: Laminator Controls

    Laminator controls c k i b j a d e f g h quick start guide setting up the laminator 1 2 3 4 steps to laminate - autolam 5 6 7 8 9 10 11 12 3 http://www.Monomachines.Com/ http://www.Monomachines.Com/.

  • Page 4: Capabilities

    Capabilities english e performance entry width 12.5” / 317mm estimated heat-up time 4 minutes cool down time 30-60 minutes lamination speed variable - max. 35” / 90cm/min laminating mechanism belt-drive ready indication light & beep auto shut-off yes (60 mins) photo-capable yes carrier-free yes impo...

  • Page 5: Laminator Controls

    Laminator controls a easy-access opening cover g selection buttons (up/down/left/right) b adjustable document entry guide h select / ok button c entry support shelf i detachable document exit tray d reverse button j on/off switch (at rear) e standby button k carry points (at sides) f lcd user interf...

  • Page 6: Setting Up The Laminator

    Setting up the laminator 1. Ensure the machine is on a stable surface. Check that there is enough clear space behind the machine to allow items to pass through freely. 2. Connect the supplied power cord to the machine. Steps to laminate - autolam 5. Switch the power on. 6. Select the ‘standby’ butto...

  • Page 7: Maintenance - Easy-Access

    Steps to laminate - manual operation on start menu, select “manual” operation within 5 seconds of switching machine on. The ‘ready’ screen will show when warm-up is complete and two short beeps indicate that machine is ready and user can insert pouch. To return to the “home” menu at any stage, press...

  • Page 8: Cleanme System Check

    Cleanme system check the cleanme system check warns the user if glue or dirt has built up inside the laminator. Glue can build up inside every lamina­ tor, especially when low-quality laminating pouches are used. We recommend using fellowes brand pouches to reduce the amount of cleaning required and...

  • Page 9: Function Overview

    Function overview open - easy-access function 0 - 30 min cleanme - maintenance overload protection - auto reverse secure mechanism and close as described above a) help - information display b) c) 9 http://www.Monomachines.Com/ http://www.Monomachines.Com/.

  • Page 10: Troubleshooting

    Troubleshooting problem possible cause solution no symbols showing in lcd screen machine is not switched on switch on machine at rear next to plug inlet and at the wall socket, then press standby button to left of lcd screen ready screen does not come on after a long period machine is in a hot or hu...

  • Page 11

    Venue, itasca, illinois 60143-1095 rance 2009 fellowes, inc. Part no. 403916-2 fcc class b notice - notification pour les etats-unis note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed ...