Summary of Z
Page 1
Z & zw owner’s manual.
Page 2
Felt z & zw internal routing manual this manual is not intended as a comprehensive use, service, repair or maintenance manual. Please see your dealer for all service, repairs or maintenance. Your dealer may also be able to refer you to classes, clinics or books on bicycle use, service, repair or mai...
Page 3
1. Mousetail ferrule 2. Cable bottom bracket cable guide 3. Brake cable housing 4. Front derailleur grommet 5. Cable housing stop (x4) 6. Hydrolic brake grommet 7. Shifter cable (x2) 8. Brake cable (x2) z & zw small parts mechanical cable & brake instruction 1 4 2 5 3 6 7 8 - 1 -.
Page 4
Rear brake cable to brake lever rear derailleur cable to shifter front derailleur cable to shifter z & zw mechanical cable internal routing road map - 2 -.
Page 5
Thread front derailleur shifter cable through the shifter and into cable housing until the head of the shifter cable is seated correctly in shifter. (depending on your shifter, may look different than the one pictured) step 1 b. A. Feed front derailleur cable into mousetail ferrule and downtube via ...
Page 6
Front derailleur cable is shown exiting the bottom bracket hole. Step 3 repeat steps 1 and 2, routing the rear derailleur cable through the right shifter, cable housing, though the cable stop and out the bottom bracket hole. Step 4 - 4 -.
Page 7
Slide the mousetail over the front derailleur cable until at least 2” of cable is exposed. Pull both cables to ensure tautness and confirm they cross over each other in the downtube, but do not touch each other, or shifting will be compromised. B. Route front derailleur cable through small bottom br...
Page 8
A. Take cable housing and apply a ferrule to each end. Fit one end into the chainstay cable housing mount and route rear derailleur cable through as pictured. B. Locate the eyelet on the rear derailleur and route rear derailleur cable though and fit ferruled cable housing into the eyelet as pictured...
Page 9
A. If necessary, slide mousetail into place; about 1” should extend through the front derailleur grommet hole as shown. If mousetail is too long, trim mousetail. B. Slide the front derailleur grommet over the front derailleur cable and press into front derailleur grommet hole as shown. Step 6 c. Mou...
Page 10
Prior to routing the rear brake, you’ll want to remove the top tube cable stop near the seat tube. Step 7 rear brake routing place the top tube cable stop and 2mm bolt aside to be in stalled after routing the rear brake cable. - 8 -.
Page 11
A. Route the rear brake cable into the top tube cable stop nearest to the frame’s head tube as pictured. * if using hydraulic brakes, be sure to replace the cable housing stop with a press-fit silicone hydraulic brake housing stop before routing hydraulic brake housing. Step 8 - 9 -.
Page 12
B. Feed cable through the top tube until cable exits rear top tube grommet nearest to the seat tube. C. Replace the top tube grommet and tighten the 2mm screw to secure in place as shown. Step 9 d. Slide the piece of rear brake cable housing (ferrule side) into the top tube grommet as shown. E. Rout...
Page 13
A. Insert brake cable into brake lever and route through cable housing. Pull taught until cable head is firmly seated in the shifter lever. Step 10 front brake cable installation b. Thread brake cable into front brake tension bolt. Exposed brake cable housing should fit into front brake tension bolt...
Page 14
- 1 2 -.
Page 15
1 4 2 5 3 6 7 8 5. Brake cable housing stop 6. Brake cable housing stop screw 7. Small di2 grommet 8. *shimano di2 wires 1. Bottom bracket grommet 2. *junction b 3. Di2 wire grommet 4. Frame grommet plug *not included with frame z & zw small parts electronic wiring instruction - 1 3 -.
Page 16
Battery cable to junction external battery (if applicable) di2 junction box b rear derailleur cable to junction front derailleur cable to junction downtube cable brain to junction z & zw electronic wire routing road map * - 1 4 -.
Page 17
A. Route the wire down thruogh the top tube wire-endtry point, through the downtube and out the bottom bracket as pictured. Step 1 shifter junction wire tip: to make routing easier, tape the end of the wire to the end of a piece of brake cable (as a steel cable is easier to route than a wire or hous...
Page 18
Route the wire, entering the small hole located under the front derailleur mount and out the hole under the bottom bracket as pictured. Press-fit the front derailleur grommet (a) into the hole to prevent di2 wire from falling into the frame. Front derailleur wire step 2 (a) b. If needed, attach fron...
Page 19
A. Route the rear derailleur wire through the hole in the drive-side dropout, through the chainstay and out the wire-exit hole under the bottom bracket as pictured. B. If needed, attach rear derailleur and plug in rear derailleur wire. Rear derailleur wire step 3 - 1 7 -.
Page 20
Front rear 1 2 3 4 a. Plug front and rear derailleur wires (1&2) into junction box (rear). Plug battery wire (3) and shifter wire (4) into junction box (front). B. After, fit the connected di2 junction b into the hole in the bottom bracket and plug with supplied bottom bracket plug as pictured. Plug...
Page 21
A b c step 8 wire grommets rear derailleur grommet front derailleur grommet downtube grommet a. Press in any remaining grommets. Refer to below images for placement. B. If not already done, connect wires to derailleurs and junction b. A b c - 1 9 -.
Page 22
Felt racing, llc 12 chrysler irvine, ca 92618 www.Feltbicycles.Com industriestr. 39 26188 edewecht germany.