Fender Pro Junior III Owner's Manual - page 7
7
7
fe nde r.co m
Rear Panel
Rear Panel
Specifications
Specifications
TYPE:
PR
257
PART NUMBERS:
223-0300-000 (120V, 60Hz)
223-0301-000 (110V, 60Hz) TW
223-0303-000 (240V, 50Hz) AUS
223-0304-000 (230V, 50Hz) UK
223-0305-000 (220V, 50Hz) ARG
223-0306-000 (230V, 50Hz) EUR
223-0307-000 (100V, 50/60Hz) JPN
223-0309-000 (220V, 60Hz) ROK
223-0310-000 (120V, 60Hz) MX
POWER REQUIREMENT:
70W
POWER OUTPUT:
15W RMS minimum into 8Ω at 5% THD, 1kHz
INPUT IMPEDANCE: 1MΩ
TUBES
PRE-AMPLIFIER: 1–Fender Groove Tube 12AX7 (P/N 007-0228-000)
1–Fender Groove Tube 12AX7 (P/N 001-3341-000)
OUTPUT: 2–Fender Groove Tubes EL84 (P/N 004-1255-000)
FUSE:
Internal (non-user serviceable)
SPEAKERS:
1–10" 8Ω Fender Special Design speaker (P/N 004-8832-000)
DUST COVER (OPTIONAL):
Fitted cover (P/N 005-4913-000)
DIMENSIONS
HEIGHT: 14 in (35.6 cm)
WIDTH: 15 in (38.1 cm)
DEPTH: 8 3/4 in (22.2 cm)
WEIGHT:
20 lb (9.1 kg)
Product specifications are subject to change without notice.
F. POWER
CORD
—
Connect to a grounded outlet in
accordance with the voltage and frequency ratings
specified on the rear panel of your amplifier.
G. SPEAKER JACK
— Connection for the internal speaker
–or– an 8Ω external speaker cabinet.
!
An 8Ω speaker load must always be connected to the Speaker
jack when the unit is ON to prevent damage to the amplifier.
H. TUBE STABILIZER
—
A shock-absorbing stabilizer is
installed on the output tubes to minimize the tube
vibration and microphonics that normally develop over
time. The stabilizer can be used with all output tubes
compatible with your Pro Junior™ III amplifier.
I. FENDER® GROOVE TUBES® — Your new Pro Junior III
amplifier comes equipped with the highest quality tubes
available, sourced from various manufacturers worldwide.
Because of occasional irregularities in supply, the specific
tube type used in each amplifier is subject to change
without notice.
When replacing the EL84 output tubes, please note the
specific tube markings on the original tubes factory
supplied with your amplifier. For example, EL84 output
tube types include, but are not limited to: GT-EL84-R;
GT-EL84-S; ST-EL84-R; etc. The installation of a different
type may require significant adjustment by a qualified
technician to avoid reduction in performance and tube
life.
Additionally, Fender Groove Tubes tests and
sorts our EL84 output tubes based on their
measured performance. The sorted tubes
are labeled with a fine rating of 1–10 and
may also be labeled with a coarse rating color
of BLUE, WHITE or RED. A pair of matched EL84
output tubes with the same fine rating (and coarse
rating, if applicable) as the original tubes will be the
perfect replacement. However, replacement tubes with
a fine rating within one number of the original tubes can
be used without rebiasing the amplifier.
If you have questions or concerns, contact your Fender
dealer or authorized service center.
J. FUSE
(NOT SHOWN)— In the unlikely event of an electrical
fault, your Pro Junior III amplifier is protected by an
internal fuse. If the unit should suddenly stop working,
take it to an authorized service center to have the fuse
replaced and the cause of the electrical fault inspected.