Art. No. Scm8001 model. No. Rct-600 4 a rotary cutting tool with circle cutting guide www.Ferm.Com www.Ferm.Com 0611-24 usa subject to change caution: before using this rotary cutting tool or any of its accessories, read this manual and follow all safety rules and operating instructions. Imported by...
Ferm 27 exploded view 02 ferm 30 26 28 24 20 22 18 16 14 12 10 a j h i g f b d c e ill.1.
Ferm 03 d nl f e p i s sf n dk 26 ferm spare parts list warning: when servicing, use only ferm replacement parts. Use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this power tool may create a safety hazard unless repa...
Ferm 25 uk d nl f e p i s sf n dk 04 ferm 3 1 2 4 ill.4 4 3 2 1 ill.5 1 2 3 ill.6.
Ferm 05 gb d nl f e p i s sf n dk 24 ferm uk d nl f e p i s sf n dk 2 1 ill.7 ill.8 ill.9.
Ferm 23 uk d nl f e p i s sf n dk 06 ferm d nl f e p i s sf n dk ill.10 ill.11 30 26 28 24 20 22 18 16 14 12 10 1 3 4 2 5 6 9 7 8 ill.12.
Ferm 07 d nl f e p i s sf n dk 22 ferm an undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the correct size to use according to cord length and nameplate amp. Rating. If in doubt, use the next heavier gauge. The smaller the gauge num...
Ferm 21 general warning: when servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. Do not use solvents when cleaning plastic parts. Plastics are susceptible to damage from various types of commercial solvents and may be damaged by their ...
Ferm 09 warning: to avoid electrical hazards, fire hazards or damage to the cutting tool, use proper circuit protection. This tool is wired at the factory for 110–120 v operation. It must be connected to a 110–120 v, 15 a time delayed fuse or circuit breaker. To avoid shock or fire, replace power co...
Ferm 19 4. Install cutting bit and freehand cutting guide as outlined on pages 15-16 of this manual. Adjust depth of cut so the bit will protrude 1/8” beyond the thickness of the drywall. 5. Hold the tool firmly with both hands and turn it on. Plunge the bit through the drywall at the mark indicatin...
Ferm 11 service • tool service must be performed only by qualified personnel. Service or maintenance performed by unqualified personnel could result in risk of injury. • when servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of...
Ferm 17 adjusting freehand cutting guide ill.7 1. Adjust freehand cutting guide depth by loosening the depth gauge locking screw (1) and moving the cutting guide foot in or out as required. Note: set the foot so the cutting bit protrudes beyond the cutting guide 1/8” more than the thickness of the m...
Ferm 13 alternating or direct current class ii construction splash proof construction watertight construction protective earthing at earthing terminal, class i tools ../min revolutions or reciprocations per minute Ø diameter 0 off position arrow warning symbol this symbol designates that this tool i...
Ferm 15 on/off switch ill.3 this rotary cutting tool is equipped with a convenient on/off switch (1) located on the side of the tool. To turn the switch on, press the side of the switch marked “–“. To turn the switch off, press the side of the switch marked “o”. Speed control switch ill.3 this rotar...
