1. DL manuals
  2. Ferrofish
  3. Media Converter
  4. Verto 32
  5. Owner's Manual

Ferrofish Verto 32 Owner's Manual

Summary of Verto 32

  • Page 1

    Owners manual version 1.0 ferrofish advanced audio applications brüderstr. 10, d-53545 linz (rhine) germany www.Ferrofish.De.

  • Page 2: 01. Table of Contents

    2 01. Table of contents 02. Safety instructions and warnings 3 03. Introduction 5 03.1 scope of delivery 5 04. Product description 6 04.1 description of the front panel 6 04.1.1 verto 32 and 64 6 04.1.2 verto mx 6 04.2 description of the rear panel 7 04.2.1 verto 32 and 64 7 04.2.2 verto mx 8 04.3 c...

  • Page 3

    3 02. Safety instructions and warnings important safety instructions safety symbols used in this manual: this symbol is an alert that there are important maintenance and operating instructions in the literature. This symbol warns the user of uninsulated, potentially dangerous voltage inside the unit...

  • Page 4

    4 • read these instructions • keep these instructions • heed all warnings • follow all instructions 1. Do not use this device near water. 2. Clean only with a dry cloth. Do not spray liquid cleaner onto the faceplate or into the ventilation slots. This may damage the front panel or cause a dangerous...

  • Page 5: 03. Introduction

    5 03. Introduction dear customer, thank you for purchasing our product. We are very pleased that you have chosen the verto series from our product range. It is designed as an easy format converter between adat (verto 32 & 64) or madi (verto mx) and the dante protocol. We have developed three differe...

  • Page 6: 04. Product Description

    6 04. Product description the verto series of devices serve as converters for your adat or madi devices. They make the integration of existing gear into a dante environment quick and easy. All essential settings are made via dante. The fanless and low heat-generating design also makes the verto seri...

  • Page 7

    7 indicates that dante has muted all channels. This may have been caused by e.G. A missing network signal or a change of the sample rate in the dante network. 2. Madi input (optical): this status led is permanently lit when the optical madi input receives a valid signal and the verto has successfull...

  • Page 8: 05. Operation

    8 5. Dante (pri/sec): use this port to connect the unit to a dante network. Use a com- mercially available ethernet cable (at least cat5) and connect it to the pri (primary) port. 04.2.2 verto mx the connections of the verto mx are explained as follows (from left to right): 1. Power supply: connect ...

  • Page 9: 06. Technical Specifications

    9 06. Technical specifications dante i/o ∙ 2x ethernet (pri/sec) sockets, 1gbit ∙ 64x64 channel brooklyn ii board built-in adat i/o (only verto 32 & 64) ∙ 4x adat input + 4x adat output, optical toslink (verto 32) ∙ 32x32 channels at 48khz, 16x16 channels at 96khz ∙ 8x adat input + 8x adat output, o...

  • Page 10: 08. Troubleshooting

    10 08. Troubleshooting error possible cause troubleshooting power led does not light power supply not plugged in or defective check the power supply the device is switched off switch on the device with the power button. Seriously. Power led flashes quickly power button pressed the power led flashes ...

  • Page 11: 09. Legal Information

    11 09. Legal information 09.1: warranty every verto is thoroughly checked and tested. Ferrofish grants a warranty of two years after purchase thru an authorized dealer or distributor. The invoice is needed as a proof- of-purchase. In case of an permanent malfunction or any other defect under warrant...

  • Page 12

    12 10. Declarations of conformity, etc. 10.1: ce conformity - emc this device fully complies to all harmonized standards for the approximation of laws of the member states for the electromechanical compatibility (emc:2014/30/eu) and european low voltage directive 2014/35/eu. 10.2: ce conformity - ro...

  • Page 13

    13 10.4: waste disposal (weee) according to common law of the eu states directive rl2002/96/eg (weee – directive on waste electrical and electronic equipment) this product must be recycled after final use and/or end of its lifetime. In case a disposal of electronic waste is not possible, the recycli...

  • Page 14

    14 notes.

  • Page 15

    15.

  • Page 16

    16 • consult the dealer or an experienced radio/tv technician for help. Warning: any modifications or other changes to this unit not approved by the party responsible for compliance could void the user’s authority to operate this equipment. 10.4: waste disposal (weee) ??? 10.5: maintenance ??? 10.6:...