1. DL manuals
  2. Ferroli
  3. Thermostat
  4. 30800013
  5. Installation & User's Instructions

Ferroli 30800013 Installation & User's Instructions

Manual is about: Radio Thermostat Mechanical Clock

Summary of 30800013

  • Page 1

    Suitable for all ferroli combination boilers radio thermostat mechanical clock part number: 30800013 installation & user instructions.

  • Page 2: Contents

    Contents page no. 3 short description 3 safety instructions 4 - 8 receiver installation 9 - 10 installation continued 11 setting the time 12 set heating on/off periods 13 set max/min room temperatures 13 manual switch 2.

  • Page 3: Short Description

    Short description short description radio thermostat mechanical clock - transmitter the radio thermostat mechanical clock is a 7 day radio frequency (rf) wireless thermostat/ timer which communicates with a special receiver designed to replace the universal digital timer fitted to most of ferroli’s ...

  • Page 4: Receiver Installation

    Receiver installation rear view of receiver radio thermostat clock receiver 4 3 2 1 live (brown) - terminal 1 neutral (blue) - terminal 2 switching wires - terminals 3 & 4 please note: if replacing universal digital timer, please ensure you now use terminals 3 & 4, instead of 3 & 5 as per universal ...

  • Page 5: Optima 01 Range

    Optima 01 range domina, modena and falcon (mf02) step 1 remove clock from control panel. Step 2 swap wiring as shown. Make sure live is connected to terminal 1 (wire colour is not conclusive of polarity) step 3 fit receiver into control panel. Note. If the radio thermostat clock is going to replace ...

  • Page 6: Domina, Modena and Falcon

    Domina, modena and falcon step 1 remove clock from control panel. Step 2 swap wiring as shown. Make sure live is connected to terminal 1 (wire colour is not conclusive of polarity) step 3 fit receiver into control panel. Domicompact range radio thermostat clock receiver universal digital clock 4 3 2...

  • Page 7: Optimax 25C

    Optimax 25c step 1 remove clock from control panel. Step 2 swap wiring as shown. Step 3 fit receiver into control panel. Maxima 35c step 1 remove the boiler front cover and lower the control box. Step 2 remove the terminal block cover. Step 3 cut off connect block bare back wires approx. 7mm and con...

  • Page 8: Optimax He Range

    Optimax he range step 1 remove boiler outer case and lower control box. Step 2 remove control box cover. Step 3 connect brown and blue jst plug onto pcb terminal block x2. Step 4 connect brown and blue onto receiver terminals 1 and 2. Make sure live is connected to terminal 1. (the wire colour is no...

  • Page 9: Installation

    Installation attention! Note: if no reception is possible it has to be checked whether any metallic cupboards or other metallic obstacles may interfere. Note: during a demand the led will show a solid light. Led button 9 location emergency running mode if no valid radio signal is received from the t...

  • Page 10: Installation

    10 installation mounting the wall plate locate and fit the transmitter, taking into consideration where not to position the transmitter as shown. The following can reduce, deflect or block radio frequency signals between the transmitter and receiver. A. Steel reinforced walls. B. Large metallic obje...

  • Page 11: Setting The Time

    11 setting the time note: panel (a) slides back to reveal reference instructions (b). Slide cover (d) off the transmitter. Turn the outer dial clockwise to set the clock hands to the correct time. Ensure the time corresponds with the correct time on the 24hr dial. 3.00pm = 15.00 not 3.00. Note: do n...

  • Page 12: Set Heating On/off Periods

    12 set heating on/off periods select the on times by pushing the tappets to the outside. Select the off times by pushing the tappets to the inside. Above shows the clock set as follows: on 3.00pm to 10.00pm (15.00-22.00) off 10.00pm to 5.00am (22.00-5.00) on 5.00am to 8.00am (5.00-8.00) off 8.00am t...

  • Page 13: Manual Switch

    13 set max/min room temperatures manual switch maximum setting - rotate the maximum dial to give the required room temperature up to 30 o c when heating is on. Minimum setting - rotate the minimum dial to a lower temperature down to 5 o c to ensure that when the heating is off a minimum room tempera...

  • Page 14: Notes

    14 notes.

  • Page 15: Notes

    15 notes.

  • Page 16

    Because of our constant endeavour for improvement details may vary from those quoted in these instructions should you require any assistance during the installation call our technical service helpline on 08707 282 885 option 1 ferroli limited, lichfield road, branston industrial estate, burton-upon-...