- DL manuals
- Fervi
- Grinder
- 50
- Operation And Maintenance Manual
Fervi 50 Operation And Maintenance Manual
Summary of 50
Page 1
Operation and maintenance manual air die grinder set with sanding attachments art. 0050 original instructions fervi.Com.
Page 2: Foreword
Hardware page 2 of 16 foreword read this manual before operating any machinery original instructions before starting any operation it is compulsory to read this instruction manual. The guarantee that the machine will function and perform properly is strictly dependent upon the application of all the...
Page 3: Contents
Hardware page 3 of 16 contents 1 general safety instructions............................................................. 4 1.1 risks associated with the work area ............................................................................4 1.2 risks associated with the presence of rotating and/or ...
Page 4: Parts
Hardware page 4 of 16 1 general safety instructions 1. During use, maintain control of the tool. The operators represent the most important aspect of safety. To best protect against the risk of injury, work cautiously and carefully. 2. The pneumatic tool should not be used and repaired by someone un...
Page 5: 1.4 Technical Support
Hardware page 5 of 16 1.3 personal protective equipment when using the pneumatic tool, always wear the following: safety shoes work gloves hearing protection (cap, earplugs, etc.) protective goggles 1.4 technical support for any problems and/or concerns, please contact, without hesitation, the custo...
Page 6: Use
Hardware page 6 of 16 2 description of the grinder and intended use the grinder is a portable pneumatic tool, to be used for grinding, finishing and chamfering of small surfaces. By changing the abrasive tools (grinding wheels), it is possible to grind or polish different materials, such as metals, ...
Page 7: 2.2 Pictograms
Hardware page 7 of 16 2.1 technical specifications operating pressure (kpa/bar) 600 / 6 air intake (l/min) 120 rotation speed (rev/min) 22,000 empty weight (kg) 0.8 sound pressure level emitted into the environment (db (a)) 82.5 vibration transmitted to the hand-arm system (m/s 2 ) 2.2 pictograms an...
Page 8
Hardware page 8 of 16 3 improper use and contraindications it is strictly forbidden !! allow the tool to be used by untrained personnel and those who have not read the instruction manual; use the tool for different purposes and uses other than those for which it was designed, i.E. Grinding, smoo...
Page 9: 4 Commissioning
Hardware page 9 of 16 4 commissioning 1. Remove the air inlet cap, then screw the nozzle into hole: 1/4" npt male quick-release coupling 2. Put a few drops of lubricating oil (without resin acid) in the air inlet nozzle. 3. Check the flexible air supply hose. If it is damaged, broken, torn or deform...
Page 10: 5 How To Use
Hardware page 10 of 16 5 how to use 5.1 attaching the abrasive tools (grinding wheels) crushing and cutting before attaching and/or removing the grinding wheels, always remove the air supply hose. Protective gloves before attaching and/or removing the grinding wheels, wear suitable protective gloves...
Page 11: Crushing And Cutting
Hardware page 11 of 16 crushing and cutting always be sure to insert the shaft of the grinding wheel into the hole of the tool chuck by at least 10mm. always make sure that the tool is assembled correctly while trying to manually remove it from the grinder. if it is too short or incorrectly ti...
Page 12: 5.2 Power On / Off
Hardware page 12 of 16 5.2 power on / off (personal protective equipment) ppe before using the grinder, wear suitable work clothing, gloves, shoes and protective goggles. Also wear a mask if you work with materials that produce dust or fumes. Also wear protective devices for the ears (hearing protec...
Page 13: Emergency
Hardware page 13 of 16 to start the grinder (to rotate the tool), press the safety lever forward with your thumb (figure 8/a), then press the lever against the housing of the grinder (figure 8/b). Figure 8 - starting the grinder. The grinder's start lever is a continuous hold lever, in the sense tha...
Page 14
Hardware page 14 of 16 6 maintenance and cleaning the purpose of this chapter is to provide all the information on maintenance procedures and their frequency as required by the grinder. Intervention frequency daily weekly 1. General visual inspection x 2. General cleaning x 3. Clean the air outlet n...
Page 15
Hardware page 15 of 16 7 bill of materials and spare parts fervi.Com.
Page 16
Hardware page 16 of 16 ref. Description ref. Description 0050/01 tool body 0050/18 bearing 0050/02 valve 0050/19 rear cylinder head 0050/03 trigger 0050/20 steel ball 0050/04 rivet 0050/21 rotor 0050/05 o-ring 0050/22 chuck fastening ring nut 0050/06 o-ring 0050/23 cylinder 0050/07 pin 0050/24 plast...