1. DL manuals
  2. Fervi
  3. Drill
  4. T066
  5. Operation And Maintenance Manual

Fervi T066 Operation And Maintenance Manual

Summary of T066

  • Page 1

    Operation and maintenance manual drilling machine art. T066 original instructions fervi.Com.

  • Page 2: Foreword

    Machines and accessories page 2 of 44 foreword read this manual before operating any machinery original instructions before starting any operation it is compulsory to read this instruction manual. The guarantee that the machine will function and perform properly is strictly dependent upon the applic...

  • Page 3: Contents

    Machines and accessories page 3 of 44 contents 1 introduction ........................................................................................ 5 2 general safety warnings ................................................................... 7 2.1 general safety rules for machine tools............

  • Page 4

    Machines and accessories page 4 of 44 11.1 routine maintenance ...............................................................................................33 11.2 lubrication...............................................................................................................33 12 troubl...

  • Page 5: 1 Introduction

    Machines and accessories page 5 of 44 1 introduction this manual is delivered with the machine, and it must be regarded as an inseparable part of it. The manufacturer holds all ownership to material and intellectual property of this manual; any disclosure or copying, even partial, of this publicatio...

  • Page 6: Pay Attention

    Machines and accessories page 6 of 44 g raphic representation of safety , operational and risk warnings the following boxes are designed to attract the attention of the reader/user for the purposes of proper and safe use of the machine: pay attention this highlights behavioural rules to prevent dama...

  • Page 7: 2 General Safety Warnings

    Machines and accessories page 7 of 44 2 general safety warnings 2.1 general safety rules for machine tools accident  the operation of drilling or tapping always presents a risk of injury associated with the possibility of accidental contact of parts of the body with the tool in motion, detachment o...

  • Page 8

    Machines and accessories page 8 of 44 1. Always check the efficiency and integrity of the machine. 2. Before connecting the machine to the mains, make sure that the rotating parts are not damaged or badly worn. Make sure that the switch is in the neutral position. 3. Do not start the machine in an e...

  • Page 9

    Machines and accessories page 9 of 44 23. It is recommended that users of this publication, for maintenance and repair, have a basic knowledge of mechanical principles and of repair technique procedures. 24. The person responsible for company safety is to make sure that the staff responsible for usi...

  • Page 10: 2.3 Technical Support

    Machines and accessories page 10 of 44 2.3 technical support for any problems or concerns, please contact, without hesitation, the dealer from whom you purchased the machine, who has competent and specialised staff, specific equipment and spare parts. 2.4 other provisions i t is forbidden to tamper ...

  • Page 11: 3 Technical Specifications

    Machines and accessories page 11 of 44 3 technical specifications characteristics: art. T066 height (mm) 2000 width (mm) 500 depth (mm) 750 weight (kg) 440 rated voltage (v) 400 power (w) 1500 spindle travel (mm) 125 drilling capacity (mm)  40 morse taper cm / mt 4 sleeve (mm)  75 column (mm)  12...

  • Page 12

    Machines and accessories page 12 of 44 4 intended use of the machine the drilling machine is a machine-tool designed for executing simple operations, such as:  drilling (max drilling capacity: 35 mm);  threading;  boring and spot-facing. The machine is made to perform such machining of different ...

  • Page 13

    Machines and accessories page 13 of 44 5 description of the machine figure 1 – overview. 1 motor 9 speed control levers 2 vertical feed handwheel 10 spindle guard 3 coolant liquid tube 11 spindle 4 table adjustment lever 12 vice 5 work table 13 vice adjustment lever 6 column 14 coolant pump 7 spindl...

  • Page 14: 5.1 Identification Plate

    Machines and accessories page 14 of 44 5.1 identification plate the identification plate of the drilling machine is located on the right side of the head (see figure 2). Figure 2 – identification plate. Fervi.Com.

  • Page 15: 5.2 Pictograms

    Machines and accessories page 15 of 44 5.2 pictograms -leggere attentamente le istruzioni prima di utilizzare la macchina -prima di intervenire sulla macchina per qualsiasi regolazione o per manutenzione togliere la spina dalla presa di corrente -fissare saldamente alla tavola il pezzo da lavorare p...

  • Page 16: Attenzione

    Machines and accessories page 16 of 44 pictograms key plate in italian plate in english -leggere attentamente le istruzioni prima di utilizzare la macchina -prima di intervenire sulla macchina per qualsiasi regolazione o per manutenzione togliere la spina dalla presa di corrente -fissare saldamente ...

  • Page 17

    Machines and accessories page 17 of 44 s pindle speed plates the plate indicating of the speed of rotation of the spindle corresponding to different gearbox configurations is on the front part of the head. Figure 3 - spindle speed labels. Minimum speed: 75 rev/min - lever configuration: i-l1. Maximu...

  • Page 18

    Machines and accessories page 18 of 44 6 description of controls and adjustments 6.1 control panel buttons and pilot lamps figure 5 - control panel. 1. Operating indicator light it lights up when the machine is turned on, using switch 2. 2. Mode switch this switch has three stable positions. When le...

  • Page 19: In Case Of Emergency

    Machines and accessories page 19 of 44 changing the direction of rotation always wait for the spindle to come to a complete stop before starting the rotation in the opposite direction to the one you are using. 6. Stop button press this button to stop the rotation of the spindle. 7. Speed switch when...

  • Page 20: 6.2 Levers And Handwheels

    Machines and accessories page 20 of 44 6.2 levers and handwheels to set the speed of rotation of the spindle, turn off the machine and choose the switch position i or ii (ref. 2 in figure 5) bring the levers (ref. 9 and 10 in figure 6), to the required position, following the directions given in the...

  • Page 21: Reversing Rotation

    Machines and accessories page 21 of 44 reversing rotation reversing rotation can take place by means of the micro switch located next to the spindle or by means of the button on the control panel. In any event, only reverse rotation at low speed max 150 rpm (levers in position l1). Anticlockwise rot...

  • Page 22

    Machines and accessories page 22 of 44 the opening / closing of the vice takes place using the lever at the end of the movable part. Figure 11 - vice lever. This handle allows the height adjustment of the table, after reaching the desired height, it is possible to lock the table using the lever loca...

  • Page 23: 7 Machine Safety Devices

    Machines and accessories page 23 of 44 7 machine safety devices accident under no circumstances should protection and safety devices be modified or removed! 7.1 spindle guard a plexiglass guard protects the operator against contact with the rotating tool or against parts ejected during the machining...

  • Page 24: 7.3 Emergency Stop

    Machines and accessories page 24 of 44 7.3 emergency stop the emergency stop is constituted by a cap red which, if pressed, activates the stop button thus interrupting the power supply of the machine. Figure 15 - emergency button. Upon pressing the emergency stop button, the spindle will keep rotati...

  • Page 25: 7.5 Use Of Ppe

    Machines and accessories page 25 of 44 in the event of drill malfunction or failure, the machines are equipped with an electric cable with conductor grounding to protect the operator from electrocution (electric shock), providing a path of least resistance for electric current thus reducing the dang...

  • Page 26: 8 Transport And Lifting

    Machines and accessories page 26 of 44 8 transport and lifting use suitable lifting equipment to move the drill. Please remember that the machine weighs about 400 kg, so please use lifting equipment with a higher maximum load capacity. Lifting cranes, cranes and hoists with sufficient load capacity ...

  • Page 27: 9 Machine Assembly

    Machines and accessories page 27 of 44 9 machine assembly to assemble the geared drilling machine, follow these steps: staff required the assembly must be carried out by at least two people. Clean the machine before starting assembly, clean the protective product from the machine's components. 1. En...

  • Page 28: Hold The Spindle

    Machines and accessories page 28 of 44 9.1 mounting the spindle cone and the spindle proceed as follows to assemble the spindle cone and the spindle: 1. With a dry cloth, clean the internal surface of the coupling of the spindle cone. Similarly, clean also the spindle and the spindle cone. 2. Insert...

  • Page 29: 10 Operation

    Machines and accessories page 29 of 44 10 operation the drilling machineerrore. Nome della proprietà del documento sconosciuto. Is a very easy machine to use. It is able to perform the drilling and tapping of metals and similar materials, other materials can be processed, using a suitable tool. Usin...

  • Page 30: Mounting The Tool

    Machines and accessories page 30 of 44 10.2drilling in manual mode unscrew the knob to loosen the worm screw cone and the spring base. Then set the stroke of the spindle by setting the positive depth of the blind holes (depth gauge) or through holes. 1. Choose an appropriate tool for the next proces...

  • Page 31: 10.3Tapping

    Machines and accessories page 31 of 44 10.3tapping use a suitable tool for tapping, then: 1. Move the switch (ref. 2 figure 5) to the t apping position. 2. Check the position of the pads on the handwheel. 3. Turn the handwheel to lower the spindle in order to start its rotation (right) and move the ...

  • Page 32: 10.5Cooling System

    Machines and accessories page 32 of 44 if necessary it is possible to turn on the lamp located behind the spindle using the switch on the front of the head. Figure 21 – lighting. 10.5cooling system on the control panel there is a switch that allows the cooling system pump to be started. Before start...

  • Page 33: 11 Maintenance

    Machines and accessories page 33 of 44 11 maintenance 11.1routine maintenance remove dust accumulated inside the motor and machining residues on the work surface using compressed air. Working with compressed air always use protective goggles when undertaking work with compressed air and do not excee...

  • Page 34

    Machines and accessories page 34 of 44 lubricate every 6 months lubricate everyday fervi.Com.

  • Page 35: 12 Troubleshooting

    Machines and accessories page 35 of 44 12 troubleshooting problem probable cause solution noisy operation a) improper belt drive b) dry spindle c) loose pulley. D) loose belt. E) broken bearing a) adjust the tension. B) remove the spindle sleeve and lubricate. C) tighten the pulley. D) adjust the be...

  • Page 36: Respect The Environment!

    Machines and accessories page 36 of 44 13 disposal of parts and materials if the machine is to be scrapped, its parts must be differentiated for disposal. Machine materials include: steel, aluminium and other metal components. Plastic materials. Copper cables, motors and electric components. Respect...

  • Page 37

    Machines and accessories page 37 of 44 14 exploded view and spare parts fervi.Com.

  • Page 38

    Machines and accessories page 38 of 44 number description t066/101 base t066/102 column t066/104 work table t066/111 vice slide t066/112 vice base t066/113 vice t066/114 vice screw t066/115 separator bearing t066/116 crank t066/117 bolt m12 t066/118 screw m12 x 100 t066/119 screw m8x25 t066/120 pin ...

  • Page 39

    Machines and accessories page 39 of 44 fervi.Com.

  • Page 40

    Machines and accessories page 40 of 44 number description number description t066/2001 cap t066/2058 screw t066/2002 retainer ring t066/2059 retainer ring t066/2004 ball bearing t066/2060 oil seal t066/2005 motor t066/2061 retainer ring t066/2006 screw t066/2062 coupling shaft t066/2007 grub screw t...

  • Page 41

    Machines and accessories page 41 of 44 number description number description t066/2135 oil seal t066/2154 oil seal t066/2136 gear t066/2155 oil seal t066/2138 retainer ring t066/2156 washer t066/2139 retainer ring t066/2157 retainer ring t066/2140 ball bearing t066/2158 grub screw t066/2141 shaft sa...

  • Page 42

    Machines and accessories page 42 of 44 fervi.Com.

  • Page 43

    Machines and accessories page 43 of 44 ref. Description ref. Description t066/301 spindle box t066/333 screw m4x6 t066/302 sprocket t066/334 sealing ring 35 t066/303 shaft support t066/335 pin 4x8 t066/304 coupling bushing t066/336 screw m4x12 t066/305 support pin t066/337 gear t066/306 pin 6x12 t06...

  • Page 44: 15 Wiring Plan

    Machines and accessories page 44 of 44 15 wiring plan fervi.Com.