1. DL manuals
  2. Fiat
  3. Automobile
  4. 2014 500C
  5. Owner's Manual

Fiat 2014 500C Owner's Manual

Summary of 2014 500C

  • Page 1

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 fia t 500 14ff500-126-ac third edition rev 1 printed in u.S.A. Fiat 500

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ! Vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 ! Sentry k...

  • Page 12

    ▫ power window switches . . . . . . . . . . . . . . . . .23 ! Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 ! Occupant restraints . . . . . . . . . . . . . . . .26 ▫ lap/shoulder belts . . . . . . . . . . . . . . . . . . . .29 ▫ lap/shoulder belt untwisting procedure . . . . .34...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 14

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children ...

  • Page 15

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 16

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 17

    General information the sentry key® system complies with fcc rules part 15 and with rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference that may be received, including interference ...

  • Page 18

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and liftgate press and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash t...

  • Page 19

    Opening power top remote function: 1. Open — push and hold the unlock button down on the key fob for a minimum of three seconds to initiate power top open. The roof will stop opening when- ever the unlock button on the key fob is released, or when it reaches the spoiler position note: if your power ...

  • Page 20

    To lock the doors and liftgate press and release the lock button on the rke transmit- ter to lock all doors and the liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Programming additional transmitters refer to sentry key® “customer key programming”. If y...

  • Page 21

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 2 things to know before starting your vehicle 19.

  • Page 22

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 23

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. (continued) warning! (continued) • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park a...

  • Page 24

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of...

  • Page 25

    Autoclose when enabled, the door locks will lock automatically when the vehicles speed exceeds 15 mph (24 km/h). To change the setting proceed as follows: 1. Briefly press the menu button to enter the menu screen. 2. Press the up or down button to highlight “autoclose”. Press the menu button, use th...

  • Page 26

    Warning! (continued) location accessible to children. Occupants, particu- larly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down the driver’s door window switch has an auto-down featur...

  • Page 27

    Second, release, and the window will go down automati- cally. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ear...

  • Page 28

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 29

    • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped pl...

  • Page 30

    Children to slide the shoulder belt behind them or under their arm. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should always wear their lap and shoulder belts properly. 3. The driver and front passenger seats shou...

  • Page 31

    Warning! (continued) • side air bags also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle ...

  • Page 32

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 33

    The belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” pulling out the latch plate inserting latch plate into buckle 2 things to know before s...

  • Page 34

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 35

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 36

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protec...

  • Page 37

    Seat belts in passenger seating positions the seat belts in the passenger seating positions are equipped with automatic locking retractors (alr) which are used to secure a child restraint system. For additional information, refer to “installing child re- straints using the vehicle seat belt” under t...

  • Page 38

    Position that has a belt with this feature. Children 12 years old and under should always be properly restrained in a vehicle with a rear seat. How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire b...

  • Page 39

    Seat belt pretensioners the seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by assuring that the belt is tight about the oc...

  • Page 40

    Unbuckled while traveling at speeds greater than 5 mph (8 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front passe...

  • Page 41

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt lo...

  • Page 42

    Note: the driver and passenger advanced front air bags are certified to new federal regulations for ad- vanced air bags. The advanced front air bags are designed to allow the air bags to have different inflation levels based on several factors, including the severity and type of collision. This vehi...

  • Page 43

    • air bag warning light • steering wheel and column • instrument panel • supplemental driver side knee air bag • knee impact bolsters • driver advanced front air bag • passenger advanced front air bag • supplemental seat-mounted side air bags (sab) • supplemental side air bag inflatable curtains (sa...

  • Page 44

    Warning! (continued) • do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air ba...

  • Page 45

    Supplemental side air bag inflatable curtain (sabic) supplemental side air bag inflatable curtains (sabic) may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers, placed adjacent to the he...

  • Page 46

    The system includes side impact sensors that are cali- brated to deploy the seat-mounted side air bags (sab) and sabic during impacts that require air bag occupant protection. Sab and sabic air bags are a supplement to the seat belt restraint system. Occupants, including children who are up against ...

  • Page 47

    Warning! (continued) • your vehicle is equipped with sabic air bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require perma- nent attachments (bolts or screws) for installation on the vehicle roof. Do ...

  • Page 48

    Orc deploys the advanced front air bags, supplemen- tal driver side knee air bag, supplemental side air bag inflatable curtain (sabic), supplemental seat-mounted side air bags (sab), and front seat belt pretensioners, as required, depending on several factors, including the severity and type of impa...

  • Page 49

    On/run or start position. If the key is in the off/ lock position, or not in the ignition, the air bag system is not on and the air bags will not inflate. The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to de...

  • Page 50

    Quantity of non-toxic gas is generated to inflate the advanced front air bags. Different air bag inflation rates are possible, based on several factors, including the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out...

  • Page 51

    Between the occupant and the door. The sab fully inflates in about 10 milliseconds. The side air bag moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the side air bag inflates. This especially ...

  • Page 52

    Enhanced accident response system in the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response system perform the follow- in...

  • Page 53

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 54

    If a reset procedure step is not completed within 45 sec- onds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front an...

  • Page 55

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the occupant restraint con- troller (orc) system servi...

  • Page 56

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 57

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the body control module (bcm) fuse block inside the vehicle for blown fuses. ...

  • Page 58

    To read data recorded by an edr, special equipment is required, and access to the vehicle or the edr is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. ...

  • Page 59

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Canadian residents should refer to transport canada’s website for additional information: • http://www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm warning! In a collision, an unrestrained child ...

  • Page 60

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 61

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 62

    Have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above t...

  • Page 63

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 64

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- odically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of posi...

  • Page 65

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 66

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 67

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 65.

  • Page 68

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the com- bined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and ...

  • Page 69

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufac- turer also allows contact. See your child re- straint owner’s manual for more information. Locating the latch anchorages t...

  • Page 70

    Locating the latch anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower an...

  • Page 71

    2. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 3. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recli...

  • Page 72

    With it and accidentally lock the seatbelt retractor. Before installing a child restraint using the latch system, buckle the seat belt behind the child restraint and out of the child’s reach. If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the...

  • Page 73

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 74

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 75

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 76

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt path. It should not move more than 1 inch (25.4 mm) in any ...

  • Page 77

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle ...

  • Page 78

    Between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the ...

  • Page 79

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or could injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured ...

  • Page 80

    Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave c...

  • Page 81

    Warning! (continued) • do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • if you are required to drive with the trunk/liftgate/ rear doors open, make sure that all windows are closed and the climate control blower switch...

  • Page 82

    Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn webbing, etc.). If there is any question regarding seat belt or retractor condition, replace the seat belt. Air bag warnin...

  • Page 83

    Warning! (continued) • never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfer- ing with the pedals or the ability to control the vehicle. • never put floor mats or other floor coverings on top of already inst...

  • Page 84

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 85: Contents

    Understanding the features of your vehicle contents ! Power convertible top — if equipped . .86 ▫ lowering the power top. . . . . . . . . . . . . . . . .86 ▫ raising the power top . . . . . . . . . . . . . . . . . .87 ▫ power convertible top relearn procedure . . . . .88 ▫ wind stop . . . . . . . . ...

  • Page 86

    ▫ ez entry feature . . . . . . . . . . . . . . . . . . . . . .104 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . .104 ▫ heated seats — if equipped . . . . . . . . . . . . .105 ▫ head restraints . . . . . . . . . . . . . . . . . . . . . . .106 ! To open and close the hood . . . . . . . . ...

  • Page 87

    ▫ to vary the speed setting . . . . . . . . . . . . . . .122 ▫ to accelerate for passing . . . . . . . . . . . . . . . .123 ! Rear park assist — if equipped . . . . . . . .124 ▫ rear park assist sensors . . . . . . . . . . . . . . . .125 ▫ rear park assist alerts. . . . . . . . . . . . . . . . . .12...

  • Page 88

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, is used to open the power top, and the driver side button, is used to close the powe...

  • Page 89

    Note: vertical movement only operates in auto open/ close mode. Raising the power top auto close from the convertible top fully open position, push the top close button for approximately one second for the three-quarter open/spoiler position. Push the top close button for approximately one second a ...

  • Page 90

    Caution! (continued) • use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicle’s interior. Warning! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be exp...

  • Page 91

    7. Continue to hold the closed button until the top begins to cycle fully open, then release the closed button. At the end of step 7 the top will automatically cycle to the fully open position, and then close to the 1/4 open position. This will confirm that the relearn procedure was success- ful. Au...

  • Page 92

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 93

    Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors the power mirror controls are located on the driver’s door trim panel. Automatic dimming mirror power mir...

  • Page 94

    The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the l (left) or r (right) to select the mirror you need to adjust. Using the mirror control switch, press on any of the four arrows for the d...

  • Page 95

    Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rearward. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activa...

  • Page 96

    Blue&me™ hands-free communication — if equipped overview windows mobile™-based fiat blue&me™ is a per- sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car. The blue&me™ system installed on your car is equipped with a hands-f...

  • Page 97

    The hands-free kit the basic characteristic of this hands-free kit is voice recognition with bluetooth® wireless technology. With this system you can make and receive calls safely and securely by using either voice commands or buttons on the steering wheel. This can be done under any driving conditi...

  • Page 98

    To get started with blue&me™ hands-free kit with voice recognition, you have to simply pair your bluetooth® wireless technology enabled mobile phone with the system. Pairing is an operation that has to be made only once. Note: • during the mobile phone pairing procedure, blue&me™ attempts to detect ...

  • Page 99

    The hands-free kit enables the following operations: • contact calling by voice — you can call a contact in your mobile phone phonebook using your voice. You can also call a contact in your phonebook by scanning through the entries on the multifunction display. (to use this option you have to transf...

  • Page 100

    Wheel. When using the hands-free phone, the audio output of a phone conversation is heard through your car sound speakers. Message reader the blue&me™ message reader enables automatic reading, through the car sound system, of the sms texts you receive on your bluetooth® wireless technology mobile ph...

  • Page 101

    • to read the messages received and stored. Messages can be read multiple times. • to call the sms text sender using the buttons on the steering wheel or voice commands. • to delete individual messages or the entire inbox using the buttons on the steering wheel or voice commands. The blue&me™ system...

  • Page 102

    Note: • the media player does not support audio files com- pressed with other formats and drm (digital rights management) protected audio files. Non-supported audio files that may be present on the usb device will be ignored. • to use the media player, you have to simply connect (directly or by an e...

  • Page 103

    Warning! (continued) • keep the owner’s manual in the car: when kept in the car, the owner’s manual will be a ready refer- ence for you and other users unfamiliar with the system. Please make certain that before using the system for the first time, all persons have access to the owner’s manual and r...

  • Page 104

    Front seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearw...

  • Page 105

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Seat height adjustment the driver’s seat height can be raised or lowered by using a le...

  • Page 106

    Ez entry feature the driver and front passenger seats have an ez entry feature for rear seat passengers. Pull forward on the release lever, located on the outboard side of the seatback, dump the seatback forward, then slide the seat forward to allow access in and out of the rear seat. Lift the seatb...

  • Page 107

    Fore/aft (memory) position on the tracks. This results in the seat back memory being set only – the track will then be locked forward of its last set fore/aft memory posi- tion. To then reset the fore/aft track memory feature (to reestablish memory function option 1), the seat has to be returned ful...

  • Page 108

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be...

  • Page 109

    The reactive head restraints will automatically return to their normal position following a rear impact. If the reactive head restraints do not return to their normal position, see your authorized dealership immediately. Note: the head restraints should only be removed by qualified technicians, for ...

  • Page 110

    Rear head restraints to raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. Refer to “occupant restraints” in “things to know before starting your vehicle”...

  • Page 111

    To open and close the hood to open the hood, two latches must be released. 1. Pull the bottom of the red hood release lever, located on the left kick panel, rearward. 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. Hood release lever hood safety latc...

  • Page 112

    3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the open position. In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on th...

  • Page 113

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. Note: the external lights can only be turned on with the ignition in the on/run position. Headlights...

  • Page 114

    High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-to-pass you can signal another vehicle with your headlights by partially pulling th...

  • Page 115

    Note: the indicators will automatically turn off when the turn has been completed and the steering wheel is returned to a straight position. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatical...

  • Page 116

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Interior lights the interior light switches are located in the overhead console. The interior lights can be set to three different positions (off/left position, center position, on/right positi...

  • Page 117

    • when the doors are unlocked with the key fob a 10 second timer is activated. • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is m...

  • Page 118

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 119

    Note: the intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to th...

  • Page 120

    Caution! (continued) • always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Rear windshield wiper rotate the...

  • Page 121

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 122

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 123

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 124

    To deactivate a soft tap on the brake pedal, pushing the canc button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Pressing the on/off button or turning the ignition switch off erases the set speed memory. To resume...

  • Page 125

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • pressing the set (-) button once will result in a 1 mph decrease in set spe...

  • Page 126

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 127

    Rear park assist sensors the four rear park assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles, in the horizontal direction, from approximately 12 in (30 cm) up to 55 in (140 cm) from the ...

  • Page 128

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 129

    Failure indications a malfunction of the rear park assist sensors or system is indicated, during reverse gear engagement, by the instrument panel warning icon and message displayed on the electronic vehicle information center (evic) display. The warning icon is illuminated and a message is displayed...

  • Page 130

    • jackhammers, large trucks, and other vibrations could affect the performance of rear park assist. • clean the rear park assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in th...

  • Page 131

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety ...

  • Page 132

    Power sunroof — if equipped the power sunroof roof switch is located in the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly ...

  • Page 133

    To open press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open...

  • Page 134

    Emergency operation in case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. I...

  • Page 135

    Electrical power outlets there is a standard 12 volt (13 amp) power outlet, located in the floor console, for added convenience. This power outlet can power mobile phones, electronics and other low power devices. Power is available when the ignition switch is in the on/run or start position. Insert ...

  • Page 136

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 137

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 138

    Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front cupholders rear cupholders 136 understanding the features of your v...

  • Page 139

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment. Push the glove compartment door upward to close it. Glove compartment latch 3 understanding the features of your vehicle ...

  • Page 140

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 141

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the instrument cluster will illuminate when the rear window defroster is on. The rear...

  • Page 142

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 143: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .143 ! Instrument cluster — pop, lounge, 500c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 ! Instrument cluster — sport. . . . . . . . . .145 ! Instrument cluster descriptions . . . . .14...

  • Page 144

    ▫ technical specifications . . . . . . . . . . . . . . . . .180 ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . . .181 ▫ general information. . . . . . . . . . . . . . . . . . . .184 ▫ functions and adjustments . . . . . . . . . . . . . .185 ▫ radio . . . . . . . . . . . . . . . . . . . ...

  • Page 145

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip computer 10 — h...

  • Page 146

    Instrument cluster — pop, lounge, 500c 144 understanding your instrument panel.

  • Page 147

    Instrument cluster — sport 4 understanding your instrument panel 145.

  • Page 148

    Instrument cluster descriptions 1. Glow plug light — if equipped this vehicle will inhibit engine cranking when the ambient temperature is less than –22° f (–30° c) and the oil temperature sensor reading indicates an engine block heater has not been used. The glow plug light will flash during in col...

  • Page 149

    3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Low fuel light when the fuel level reaches approximately 1.0 gallon (3.8l) this light will turn on, and remain on until fuel is added. 5. High beam indicator this light indicates that the h...

  • Page 150

    9. Air bag warning light this light will turn on for four seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “o...

  • Page 151

    13. Power steering system warning this light is used to manage the electrical warning of the eps (power steering system). Refer to “power steering” in “starting and operating” for further information. 14. Electronic throttle control (etc) light this light informs you of a problem with the electronic...

  • Page 152

    One or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and...

  • Page 153

    Caution! (continued) equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehic...

  • Page 154

    Most situations, the vehicle will drive normally and will not require towing. Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic convert...

  • Page 155

    20. Brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake warning light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the brake system r...

  • Page 156

    21. Electronic stability control off (esc off) indica- tor light this light indicates the electronic stability con- trol system (esc) has been turned off by the driver. 22. Electronic stability control (esc) activation / mal- function indicator light the esc activation/malfunction indicator light in...

  • Page 157

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the on/run position, have the light inspected by an authorized dealer. 24. Door ajar this light will tu...

  • Page 158

    Caution! (continued) temperature gauge are lit, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. Warning! ...

  • Page 159

    Note: if the vehicle is equipped with the electronic vehicle information center (evic) in the instrument cluster, all warnings including “door” and “gate” and “change engine oil” will only be displayed in the evic display. Refer to “electronic vehicle information center (evic) in “understanding your...

  • Page 160

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 161

    Evic displays sport instrument cluster 1 — temperature indicator 6 — message display 2 — fuel level gauge 7 — coolant temperature gauge 3 — clock 8 — digital speedometer 4 — odometer 9 — ice warning indicator 5 — sport mode 10 — gear shift indicator (gsi) premium instrument cluster 1 — ice warning i...

  • Page 162

    Evic control buttons press the menu button briefly to access the menu and/or go to next screen or to confirm the required menu option. Press and hold the menu button (approximately one second) to return to the main screen. Press the up button to scroll upward through the displayed menu and the relat...

  • Page 163

    • set date • see radio • speed display • autoclose • units • language • buzzer volume • button volume • daylights (d.R.L.) • hill start • tire pressure • unlock driver door first • unlock all doors • exit menu selecting an option of the main menu without submenu 1. Briefly press the menu button to s...

  • Page 164

    3. Briefly press the menu button to select the displayed submenu option and to open the relevant setup menu. 4. Press the up or down button (by single presses) to select the new setting for this submenu option. 5. Briefly press the menu button to store the new setting and go back to the previously s...

  • Page 165

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as; t...

  • Page 166

    Start of trip procedure with the ignition on, push and hold the trip button for over one second to reset. Exit trip to exit the trip function, wait until all the values have been displayed or hold the menu button for longer than one second. Briefly push the menu button to go back to the menu screen ...

  • Page 167

    Values displayed range this indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving conditions will not change. The message “----” will appear on the display in the following cases: • distance less than 30 miles (or 50 km). • the vehicle is parked for ...

  • Page 168

    Personal settings (customer-programmable features) dimmer the evic display is provided with a light sensor capable of detecting environmental light conditions and adjust- ing the brightness of the instruments accordingly. Note: the brightness of the instrument panel may change while travelling follo...

  • Page 169

    3. When the function is activated (on), briefly press the menu button to display the presently set activation speed. Pressing the up or down buttons selects the speed limit. Press menu to confirm selection. Note: the setting can be increased or decreased by 5 mph or km/h each time the up/down button...

  • Page 170

    2. Press the up or down button to select trip b data. Press the up or down buttons to turn on or off 3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. Set time (cl...

  • Page 171

    • briefly press the menu button to return to the “time” sub-function. • when accessing the “mode” submenu, briefly press the menu button. The previously set display format will flash on the display. • press the up or down button to select “24h” or “12h.” when you have selected the required settings,...

  • Page 172

    • briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. See radio (repeat audio information) with this function active, the evic display shows infor- mation relevant to t...

  • Page 173

    2. Press the up or down button to select display deactivation “off”, “mph” or “km/h”. 3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen. Autoclose with this function active, the doors will auto...

  • Page 174

    4. When accessing the “distance” submenu: briefly press the menu button. Either “mi” or “km” will appear on the display (according to the previous setting). 5. Press the up or down button for setting. 6. Briefly press the menu button to return to the sub-menu. 7. When accessing the “fuel economy” su...

  • Page 175

    Language (selecting the language) the messages can be displayed in the following lan- guages: italian, english, turkce, nederlands, spanish, french, dutch, polish, brasilian. To set the required language, proceed as follows: 1. Briefly press the menu button. Press the up or down button to highlight ...

  • Page 176

    Button volume (button volume adjustment) this function may be used to adjust the volume of the beep accompanying the buttons. Menu, up or down buttons can be adjusted according to 8 levels. To adjust the volume, proceed as follows: 1. Briefly press the menu button. Press the up or down button to hig...

  • Page 177

    4. Briefly press the menu button to go back to the menu screen, or press and hold the button (approximately one second) to go back to the main screen without storing the settings. Gsi (gear shift indicator) this function may be used to set the gear shift indicator in two submenus: “fuel econ on” and...

  • Page 178

    Hill start assist this function is used when starting a vehicle from a stop on a hill. Hill start assist maintains the same level of brake pressure the driver applied for a short period of time after the foot has been removed from the brake pedal. Proceed as follows to switch this function on or off...

  • Page 179

    Entry (rke) transmitter unlock button. When unlock drivers door is selected, you must press the rke trans- mitter unlock button twice to unlock the passenger door. When all doors is selected, both of the doors will unlock on the first press of the rke transmitter unlock button. To make your selectio...

  • Page 180

    Introduction the radio has been designed according to the specifica- tions of the passenger compartment, with a personalized design to match the style of the dashboard. If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The instructions for use are ...

  • Page 181

    Cds the presence of dirt, scratches or distortions on the cds could cause skipping and poor sound quality while it is playing. For optimal playback conditions, follow these guidelines: • only use branded cds. • clean every cd thoroughly removing any finger marks or dust using a soft cloth. Hold cds ...

  • Page 182

    Copied is often shown in very small letters or is difficult to read on the actual cd cover where it may be, for example, “copy control,” “copy pro- tected,” “this cd cannot be played on a pc/mac.” • the cd player is capable of reading most compression systems currently in use, following the developm...

  • Page 183

    Quick guide radio controls button general functions mode on short button press off short button press tuner am, fm, sat (if equipped) source selection short repeated button press a-b-c cycles a, b, c presets for am, fm, sat (if equipped) short repeated button press media cd/aux/media player (if equi...

  • Page 184

    Button general functions mode (mute/pause button) volume activation/deactivation (mute/pause) short button press audio audio adjustments: low tones (bass), high tones (treble), left/ right balance (balance), front/ rear balance (fader) menu activation: short button press adjustment type selection: p...

  • Page 185

    Button radio functions mode radio station search: • automatic search • manual search automatic search: press buttons or (long press for fast for- ward) manual search: press buttons or (long press for fast forward) 1 2 3 4 5 current radio station storing long button press for memory pre- set 1 to 5 r...

  • Page 186

    General information the radio offers the following functions: radio section • pll tuning with fm/am bands • rbds (radio broadcast data system) • automatic/manual station tuning • fm multipath detector • manual storing of 25 stations (base radio) and 40 stations (if equipped with satellite): 15 on fm...

  • Page 187

    Cd/mp3 section • mp3-info function (id3-tag) • folder selection (previous/next) • track selection (forward/backward) • fast forward/rewind through tracks • mp3 display function: display of folder name, id3- tag information, time elapsed since the start of the track, name of the file • playing audio ...

  • Page 188

    Selecting the radio functions by pressing the tuner button briefly and repeatedly, the following audio sources can be selected cyclically: • am, fm and satellite bands (if equipped) selecting the cd function by briefly pressing the media button, the cd audio source can be selected (only if a cd is l...

  • Page 189

    Use the buttons or to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions managed by the audio menu are: • bass (bass adjustment) • midrange (midrange adjustment) • ...

  • Page 190

    2. Press the or button to set “balance” in the audio menu. 3. Press the button to increase the sound from the left speakers or the button to increase the sound from the right speakers. By pressing the or buttons briefly, the levels will change progressively. By pressing them down longer, the levels ...

  • Page 191

    Preset/user/classic/rock/jazz functions — if equipped the built-in equalizer can be activated/deactivated. When the equalizer function is off, the audio settings can only be changed by adjusting the “bass” and “treble” settings, whereas when the function is on, the acoustic curves can be adjusted. T...

  • Page 192

    Menu menu button functions press the menu button briefly to activate the menu function. Use the or buttons to scroll through the menu functions. To change the setting of the selected func- tion, use the or buttons. The current status of the selected function appears on the display. The functions man...

  • Page 193

    • high: function activated (high sensitivity) on volume limit this function makes it possible to activate/deactivate the maximum volume limit when turning the radio on. The display shows the function status: • “on volume limit: on” – when the radio is turned on the volume level will be: – if the vol...

  • Page 194

    The chosen mode appears on the display: • “radio off: 00 min” — the radio turns off in connec- tion with the ignition key; the radio is turned auto- matically off as soon as the key is turned to the stop position. • “radio off: 20 min” — the radio turns off indepen- dently from the ignition key; the...

  • Page 195

    Frequency band selection with the radio mode active, press the fm or am tuner button briefly and repeatedly to select the desired recep- tion band. Each time the button is pressed the following bands are selected cyclically: • am, fm or sat (if equipped) each band is highlighted by the corresponding...

  • Page 196

    Manual tuning this is used to manually search for stations in the preselected band. Select the desired frequency band and then press briefly and repeatedly the or button to start the search in the desired direction. If the or button is pressed longer, the fast search starts and then stops when the b...

  • Page 197

    Siriusxm satellite radio program types program types can be selected by pressing the or buttons. The program type will change to the next category and the radio will then tune to first station in that program type. Pressing or buttons will tune to only the stations in that program type. Pressing the...

  • Page 198

    Your service, either call the number listed on the display or visit the provider online. Caution! Neither sirius nor fiat is responsible for any errors in accuracies in the sirius data services or its use in vehicles. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. And...

  • Page 199

    Satellite radio antenna — if equipped the antenna for the satellite radio is mounted on the roof of the vehicle. Do not place items on the roof around the roof top antenna location. Objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should b...

  • Page 200

    Cd loading/ejecting to load the cd, insert it gently into the slot to activate the motorized loading system, which will position it cor- rectly. The cd can be loaded with the radio off and the ignition key turned to on/run. In this case, the radio will remain off. When the radio is turned on, the la...

  • Page 201

    Display information when the cd player is operating, information will ap- pear on the display with the following meaning: • “track 5” indicates the cd track number. • “03:42” indicates the time elapsed since the start of the track (if the relevant menu function is activated). Track selection briefly...

  • Page 202

    Mp3 mode in addition to playing regular audio cds, the radio is also enabled to play cdroms on which compressed audio files have been recorded in an mp3 format. To guarantee optimal reproduction, it is advisable to use good quality cds burned at the lowest speed possible. The files on an mp3 cd are ...

  • Page 203

    Note: when the function is activated the radio may take a few seconds to start playing. While checking the disc the display will show “cd reading.” if no mp3 files are detected, the radio will resume playing the audio session from the point where it was interrupted. Display information id3–tag infor...

  • Page 204

    • if the mp3 files on a cd-rom are structured in sub-folders their structure is compressed to a single level structure, where the sub-folders are taken to the level of the main folders. Troubleshooting general sound volume low the fader function should be adjusted to the values “f” (front) only to p...

  • Page 205

    Operating instructions — hands-free phone (if equipped) refer to the appropriate “blue&me™ user’s manual” for further information. Personal/portable navigation device (pnd) — if equipped a personal/portable navigation device (pnd) is avail- able as optional equipment for this vehicle, refer to the n...

  • Page 206

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 207

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gram...

  • Page 208

    4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. Note: if you experience difficulty in playing a particular dis...

  • Page 209

    Manual heating and air conditioning the manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the sca...

  • Page 210

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 211

    Require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • defrost air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side w...

  • Page 212

    1. Auto temperature control (atc) button controls airflow, temperature, distribution, and air recir- culation automatically. Press and release to select. Per- forming this function will cause the atc to switch between manual mode and automatic modes. Refer to “automatic operation” for more informati...

  • Page 213

    Reducing moisture on the windshield. Performing this function will cause the atc to switch into manual mode. 6. Front defrost press and release to change the current setting. The indicator illuminates when on. The blower will auto- matically default to medium-high if the defrost mode is selected. Pe...

  • Page 214

    Note: • when in defrost mode, the recirculation button will flash if pressed. This indicates that you can not proceed to this mode due to fogging risk. • when the auto indicator is on and the recirculation indicator is off, the recirculation is in auto mode. If the recirculation indicator is on, the...

  • Page 215

    On low until the engine warms up. The blower will increase in speed and transition into auto mode. Manual operation this system offers a full complement of manual override features. Note: each of these features operates independently from each other. If any feature is controlled manually, temperatur...

  • Page 216

    Floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Bi-level air is directed through the panel and floor outlets. Press and release the panel mode button and floor mode button to enter bi-level mode, the indicators ill...

  • Page 217

    Outlets. If economy mode is desired, press the a/c button to turn off the a/c mode in the atc display and deactivate the a/c system. Note: • if the system is in mix or defrost mode, the a/c can be turned off, but the a/c system shall remain active to prevent fogging of the windows. • if fog or mist ...

  • Page 218

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the a/c button) on will clear the fog. Adjust the temperature cont...

  • Page 219

    Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use recir- culation a/c mode to provide additional comfort while in automatic mode. Winter operation when operating the system during the winter m...

  • Page 221: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .223 ▫ manual transmission — if equipped . . . . . . .223 ▫ automatic transmission — if equipped . . . . .223 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .223 ▫ cold weather operation . . . . . . . ....

  • Page 222

    ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .238 ! Driving on slippery surfaces . . . . . . . . .240 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .240 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 ! Driving through water . . . . . . . . ....

  • Page 223

    ! Tires — general information . . . . . . . .269 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .269 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .270 ▫ tire pressures for high speed operation . . . .272 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .272 ▫...

  • Page 224

    ▫ materials added to fuel . . . . . . . . . . . . . . . .296 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .296 ▫ carbon monoxide warnings . . . . . . . . . . . . .297 ! Adding fuel . . . . . . . . . . . . . . . . . . . . . . . .298 ▫ fuel filler cap (gas cap) . . . . . . . . . . . . . ....

  • Page 225

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 226

    Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Cold weather operation to prev...

  • Page 227

    3. If the engine fails to start within 10 seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engine fails to start after 8 attempts, allow the starter to cool for at least 10 minutes...

  • Page 228

    Turbocharger “cool down” this vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off. Depending on the type of driving and the amount of cargo, the pump will run for up to 10 minutes after the engine has been shut off to circulate coolant through the turboch...

  • Page 229

    Note: to shift into reverse from neutral, lift the ring under the knob and, at the same time move the gearshift lever to the right and then backward. Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Da...

  • Page 230

    Recommended shift speeds to use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following table. Manual transmission recommended shift speeds units in mph (km/h) engine size acceleration rate 1 to 2 2 to 3 3 to 4 4 to 5 1.4l/1.4l turbo engine accel 14 (23) ...

  • Page 231

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 232

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 233

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 234

    The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilomete...

  • Page 235

    Note: if the shift lever cannot be moved to the park, reverse, or neutral position (when pushed for- ward) it is probably in the autostick® (+/-) position (beside the drive position). In autostick® mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the shift lev...

  • Page 236

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 237

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 238

    • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a comp...

  • Page 239

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal ope...

  • Page 240

    In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the transmission into park. 3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shi...

  • Page 241

    Forward (-) triggers a downshift, and rearward (+) an upshift. The current gear is displayed in the instrument cluster. Note: in autostick® mode, the transmission will only shift up or down when the driver moves the shift lever rearward (+) or forward (-), except as described below. • the transmissi...

  • Page 242

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces ma...

  • Page 243

    2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. Driving through w...

  • Page 244

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stopping distances. Therefore, after driving throu...

  • Page 245

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 246

    If the steering icon is displayed and the “power steer- ing system over temp” message is displayed on the evic screen, they indicate that extreme steering maneu- vers may have occurred which caused an over tempera- ture condition in the power steering system. Once driv- ing conditions are safe, pull...

  • Page 247

    When the parking brake is applied with the ignition switch in the mar (acc/on/run) position, the brake warning light in the instrument cluster will illuminate. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill gra...

  • Page 248

    Warning! (continued) • do not leave the key fob in or near the vehicle or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a c...

  • Page 249

    1. To activate the sport mode, press the sport button. Once activated, a sport message will be displayed in the instrument cluster. 2. Momentarily release the accelerator pedal. 3. Press the accelerator pedal again to activate. Automatic transmission — if equipped the sport mode increases steering f...

  • Page 250

    1. To activate the sport mode, press the sport button. Once activated, a sport message will be displayed in the instrument cluster. 2. Press the sport button again to return to the standard driving mode. Brake system in the event power assist is lost for any reason (for example; repeated brake appli...

  • Page 251

    Electronic brake control system your vehicle is equipped with a advanced electronic brake control system that includes the anti-lock brake system (abs), brake assist system (bas), traction con- trol system (tcs), hill start assist (hsa), and electronic stability control (esc). All systems work toget...

  • Page 252

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize t...

  • Page 253

    Warning! • the brake assist system (bas) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. • the bas cannot prevent collisions, including those resulting from excessive speed in turns, driving on very sli...

  • Page 254

    System will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move in the intended direction of travel. Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 2.5% (manua...

  • Page 255

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or und...

  • Page 256

    Note: the esc off switch is located left of the steering column (manual transmission only). Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot pre...

  • Page 257

    Esc operating modes the esc system has two available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started, the esc system will be in on mode. This mode should be used for most driving situations. Esc should only be turned to partial off for specific rea...

  • Page 258

    Warning! • when in “partial off” mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the “esc off indicator light” will be illuminated. When in “partial off” mode, the engine power reduction feature of tcs is disabled, and t...

  • Page 259

    Note: • the esc activation/malfunction indicator light and the esc off indicator light come on momentarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. The esc off indicator light indicates the elec...

  • Page 260

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 261

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards $ ....Blank....$ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215...

  • Page 262

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 263

    Example: load identification: $ ....Blank....$ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a s...

  • Page 264

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 265

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 266

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 264 starting and operating.

  • Page 267

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 268

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this section. To determine the maximum loading conditions of your ...

  • Page 269

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 270

    268 starting and operating.

  • Page 271

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 272

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 273

    • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard...

  • Page 274

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 275

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). Tire ty...

  • Page 276

    If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with y...

  • Page 277

    Spare tires — if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, f...

  • Page 278

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary ...

  • Page 279

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 280

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 281

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 282

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 283

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage: • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on front tires. • due to limite...

  • Page 284

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 285

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 286

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

  • Page 287

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 288

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if un...

  • Page 289

    Xxx.X psi” text message will display when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The...

  • Page 290

    2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warn- ing limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. 3. However, after driving the vehi...

  • Page 291

    The tpms consists of the following components: • receiver module • four tire pressure monitoring sensors • various tire pressure monitoring system messages, which display in the electronic vehicle information center (evic) • tire pressure monitoring telltale light tire pressure monitoring low pressu...

  • Page 292

    To be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this informa- tion. Tpms warning when a system fault is detected, the “tire pressure monitoring telltale light” will flash on and off for 75 seconds and then remain on solid. The system fault will sound a chime...

  • Page 293

    A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumula...

  • Page 294

    Telltale light” will flash on and off for 75 seconds and then remain on solid. In addition, the evic will display a “service tpm system” message and then display dashes (- -) in place of the pressure value. • for each subsequent ignition switch cycle, a chime will sound, the “tire pressure monitorin...

  • Page 295

    Fuel requirements — 1.4l engine this engine is designed to meet all emis- sion regulations and provide satisfactory fuel economy and performance when us- ing high-quality unleaded #regular# gaso- line with a minimum octane rating of 87. For optimum performance and fuel economy the use of 91 octane o...

  • Page 296

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasoline contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of refo...

  • Page 297

    If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have some or all of these symptoms: • operate in a lean mode. • obd ii “malfunction indicator light” on. • poor engine performance. • poor cold start and cold drivability. • increased risk for fuel system component corrosio...

  • Page 298

    Materials added to fuel all gasoline sold in the united states is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the f...

  • Page 299

    Note: intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: (continued) warning! (continue...

  • Page 300

    Adding fuel fuel filler cap (gas cap) the gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. Caution! • damage to the fuel system or emission control system could result from using an improper f...

  • Page 301

    Warning! (continued) • never add fuel when the engine is running. It may cause the mil to turn on and could cause a fire. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Not...

  • Page 302

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none transmission in neutral not allowed dolly tow front ok ok rear not allowed not allowed on trailer all ok ok 300 star...

  • Page 303

    This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the ground. This vehicle may also be towed using a tow dolly (with the front wheels off the ground). Vehicles equipped with manual transmissions may be flat towed (with all four wheels on the ground) at any le...

  • Page 305: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .305 ! If your engine overheats . . . . . . . . . . . .305 ! Tirefit kit — if equipped . . . . . . . . . . . . .307 ▫ tirefit storage . . . . . . . . . . . . . . . . . . . . . .307 ▫ tirefit kit components and operation...

  • Page 306

    ▫ jump-starting procedure . . . . . . . . . . . . . . . .335 ! Freeing a stuck vehicle . . . . . . . . . . . . .336 ! Shift lever override . . . . . . . . . . . . . . . .338 ! Towing a disabled vehicle . . . . . . . . . . .340 ▫ automatic transmission . . . . . . . . . . . . . . . . .341 ▫ manual tr...

  • Page 307

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 308

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 309

    Tirefit kit — if equipped small punctures up to ¼” (6 mm) in the tire tread can be sealed with tirefit. Foreign objects (e.G., screws or nails) should not be removed from the tire. Tirefit can be used in outside temperatures down to approximately -4°f (-20°c). This kit will provide a temporary tire ...

  • Page 310

    Tirefit kit components and operation using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hos...

  • Page 311

    Using the power button push and release the power button (4) once to turn on the tirefit kit. Push and release the power button (4) again to turn off the tirefit kit. Using the deflation button press the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tirefit...

  • Page 312

    The vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tirefit kit. • you can use the tirefit air pump to inflate bicycle tires. The...

  • Page 313

    Warning! (continued) • keep tirefit away from open flames or heat source. • a loose tirefit kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tirefit kit in the place provided. Failure to follow these warnings can result in injuries that are ...

  • Page 314

    Kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceed- ing. 3. Place the transmission in park (auto transmission) or in gear (manual transmission) and turn off the igni- tion. 4. Set the p...

  • Page 315

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Press the power button (4) to turn off the tirefit kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is free...

  • Page 316

    Latch pillar (recommended pressure). Check the tire pressure by looking at the pressure gauge (3). If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tir...

  • Page 317

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tirefit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected a...

  • Page 318

    If the tire pressure is 19 psi (1.3 bar) or higher: 1. Press the power button (4) to turn on tirefit and inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door opening. Note: if the tire becomes over-inflated, press the defla- tion button to redu...

  • Page 319

    5. Position the new sealant bottle (1) in the housing so that the sealant hose (6) aligns with the hose slot in the front of the housing. Press the bottle into the housing. An audible click will be heard indicating the bottle is locked into place. 6. Verify that the cap is installed on the fitting a...

  • Page 320

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Wheel mounting surface torque patterns 318 what to do in emergencies.

  • Page 321

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Jacking and tire changing — if equipped warning! • do not attempt to change a tire on the side of the ve...

  • Page 322

    Jack location the jack and jack wrench tool are stowed in a bag under the front driver’s seat. Spare tire removal the spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear cargo area. Jack and jack-handle location winch access plug 320 what to do in emerg...

  • Page 323

    2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow you to pull the tire out from under the vehicle. Lowering/raising spare tire 6 what to do in emergencies 321.

  • Page 324

    Caution! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can dam- age the winch. 3. Pull the spare tire out from under the vehicle. Spare tire 322 what to do in emergencies.

  • Page 325

    4. Tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough...

  • Page 326

    6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warning! Carefully follow the...

  • Page 327

    Warning! (continued) • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve s...

  • Page 328

    Note: before using the swivel wrench to remove the wheel bolts be sure to remove the center cap of the wheel by inserting the angled tab end of the swivel wrench into the notched part of the center cap. 3. Loosen, but do not remove, the wheel bolts by turning them to the left one turn while the whee...

  • Page 329

    Do not raise the vehicle until you are sure the jack is securely engaged. 4. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 330

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Using the swivel wrench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only unt...

  • Page 331

    7. Install the spare wheel and wheel bolts with the cone shaped end of the bolts toward the wheel. Lightly tighten the bolts. To avoid the risk of forcing the vehicle off the jack, do not tighten the bolts fully until the vehicle has been lowered. 8. Lower the vehicle by turning the jack screw to th...

  • Page 332

    12. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. Road tire installation vehicles equipped with wheel covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not...

  • Page 333

    3. Install the four wheel bolts with the cone shaped end of the nut toward the wheel. Lightly tighten the wheel bolts. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel bolts fully until the vehicle has been lowered. Failure to follow this warning may result in...

  • Page 334

    3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Refer to “torque specifications” in this sec- tion for correct wheel bolt torque. 5. After 25 miles (40...

  • Page 335

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or el...

  • Page 336

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 337

    Jump-starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 338

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the...

  • Page 339

    And reverse (with automatic transmission) or 2nd gear and reverse (with manual transmission), while gently pressing the accelerator. Use the least amount of accel- erator pedal pressure that will maintain the rocking motion, without spinning the wheels, or racing the engine. Caution! Racing the engi...

  • Page 340

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 341

    4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the access hole, and push and hold the override release lever in. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever ov...

  • Page 342

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground automatic transmission manual transmission flat tow none not allowed if transmission is operable: • transmission in neutral • 65 mph (1...

  • Page 343

    Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members ...

  • Page 344

    Caution! • do not flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. Damage from improper towing is not covered un- der the new vehicle limited warran...

  • Page 345

    • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • unlock the doors automatically. After the event occurs, when the system is active, t...

  • Page 346

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 347: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 1.4l . . . . . . . . . .347 ! Engine compartment — 1.4l turbo . . . .348 ! Onboard diagnostic system — obd ii . .349 ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .349 ! Replacement parts . ....

  • Page 348

    ▫ automatic transmission — if equipped . . . . .378 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .380 ▫ convertible top care – if equipped . . . . . . . .386 ! Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ interior fuses...

  • Page 349

    Engine compartment — 1.4l 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — air cleaner filter 3 — brake fluid reservoir 7 — engine oil fill 4 — front distribution unit (fuses) 8 — washer fluid reservoir 7 maintaining your vehicle 347.

  • Page 350

    Engine compartment — 1.4l turbo 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — engine oil fill 3 — brake fluid reservoir 7 — washer fluid reservoir 4 — front distribution unit (fuses) 348 maintaining your vehicle.

  • Page 351

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 352

    For states that require an inspection and mainte- nance (i/m), this check verifies the “malfunction indicator light (mil)” is functioning and is not on when the engine is running, and that the obd ii system is ready for testing. Normally, the obd ii system will be ready. The obd ii system may not be...

  • Page 353

    If your obd ii system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your obd ii system to update. A rech...

  • Page 354

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. Maintenance procedures the pages tha...

  • Page 355

    Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Do ...

  • Page 356

    Engine oil selection — 1.4l engine for best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are api certified and meet the requirements of chrysler material standard ms-6395. Engine oil selection — 1.4l turbo engine for be...

  • Page 357

    Engine oil viscosity — 1.4l engine (sae grade) sae 5w-30 engine oil recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- me...

  • Page 358

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any a...

  • Page 359

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 360

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 361

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 362

    Protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system pag compressor oil, and refrige...

  • Page 363

    2. Pull the console closeout cover rearward to disengage the front retaining tab and remove the cover. 3. Remove the two 5.5 mm screws (1 and 2) that secure the particulate air filter cover to the hvac housing. Torx® screw location console closeout panel 7 maintaining your vehicle 361.

  • Page 364

    4. Remove the a/c air filter by pulling it straight out of the housing. Take note of the air filter position indica- tors. 5. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Air filter cover screw locations a/c air filter 362 maintaining ...

  • Page 365

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 6. Install the passenger side console closeout. Refer to the “maintenance schedule” for the proper mainte...

  • Page 366

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make s...

  • Page 367

    Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. ...

  • Page 368

    5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with wind- shield washer solvent (not engine coolant/ antifreeze)...

  • Page 369

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 370

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 371

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 372

    Refer to the “maintenance schedule” for the proper maintenance intervals. Note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your loca...

  • Page 373

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 374

    (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area whe...

  • Page 375

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 376

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 377

    • do not change the thermostat for summer or winter operation. If replacement is ever necessary, install only the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure ...

  • Page 378

    Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch ...

  • Page 379

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 380

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 381

    Caution! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. Special additives the manufacturer s...

  • Page 382

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 383

    • insects, tree sap and tar. • salt in the air near seacoast localities. • atmospheric fallout/industrial pollutants. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if ...

  • Page 384

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 385

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 386

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. ...

  • Page 387

    Glass surfaces all glass surfaces should be cleaned on a regular basis with mopar® glass cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window ...

  • Page 388

    Seat belt maintenance do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry ...

  • Page 389

    Caution! Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • avoid high-pressure car washes, as they can dam- age the top material. Also, increased water pressure may force past the weather strips. • remove any standing water from the top and dry...

  • Page 390

    Before washing the top. The top should be washed with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dishwashing soap. Do not use detergent. Caution! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic sol- vents, petroleum dis...

  • Page 391

    Warning! (continued) • before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • if the replaced fuse blows again, contact an autho- rized dealer. • if a general protection fuse for safety systems (air bag system, braking system...

  • Page 392

    Cavity vehicle fuse number mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 5 amp tan front and rear ceiling lights trunk and door courtesy lights 3 f53 5 amp tan instrument panel node 4 f38 20 amp yellow central door locking 5 f36 10 amp red diagnostic socket, car radio, climate contr...

  • Page 393

    Cavity vehicle fuse number mini fuse description 12 f49 5 amp tan exterior mirror, gps, electric mirror, parking sensor 13 f31 5 amp tan ignition, climate control 14 f47 20 amp yellow driver power window underhood fuses the front distribution unit is located on the right side of the engine compartme...

  • Page 394

    The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Cavity maxi fuse mini fuse description f01 60 amp blue body controller f02 20 amp yellow audio amplifier f03 20 amp yellow ignition switch f04 40 amp orange anti-lock brake pump f05 70 amp t...

  • Page 395

    Cavity maxi fuse mini fuse description f11 10 amp red powertrain (multiair – if equipped) f14 5 amp tan high beam (shutter) f15 15 amp blue cigar lighter f16 7.5 amp brown transmission f17 25 amp white powertrain (multiair – if equipped) f17 15 amp blue powertrain f18 15 amp blue powertrain f18 5 am...

  • Page 396

    Cavity maxi fuse mini fuse description f82 30 amp green sunroof/convertible top f83 20 amp yellow cooling pump – if equipped f84 10 amp red transmission f85 30 amp green (ato) rear defroster f87 5 amp tan rear defroster f90 5 amp tan heated mirrors – if equipped vehicle storage if you are leaving yo...

  • Page 397

    Replacement bulbs interior bulbs bulb number overhead lamp c5w courtesy lamp w5w exterior bulbs bulb number front low and high beam headlamp hir2 front parking/daytime running lamps w21/5w front fog lamps h11 front side marker lamps w3w front turn signal lamps wy21w bulb number side direction lamps ...

  • Page 398

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps low beam and high beam 1....

  • Page 399

    3. Remove the plastic cap from the back of the lamp housing. 4. Rotate bulb/socket counter-clockwise. 5. Remove the bulb and replace as needed. 6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 7. Reinstall the plastic cap. Front fog lamps to replace th...

  • Page 400

    3. Remove four screws and separate the backplate from the lamp housing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted ...

  • Page 401

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4l/1.4l turbo engine 4 quarts 3.8 liters cooling system 1.4l/1.4l turbo engine (mopar® antifreeze/engine coolant 10 year/150,000 mile formula) — with manual transmission 4.6 quarts 4.4 liters 1.4l/1.4l tu...

  • Page 402

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant - 1.4l/1.4l turbo engine we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) meeting the requirements of chrysler ma- terial standard ms-12...

  • Page 403

    Component fluid, lubricant, or genuine part spark plugs - 1.4l engine we recommend you use mopar® spark plugs spark plugs - 1.4l turbo engine we recommend you use mopar® spark plugs fuel selection - 1.4l/1.4l turbo engine 87 octane acceptable — 91 octane recommended chassis component fluid, lubrican...

  • Page 405: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .404 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .406 8.

  • Page 406

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 407

    Once a month or before a long trip: • check engine oil level. • check windshield washer fluid level. • check the tire inflation pressures and look for unusual wear or damage. • check the fluid levels of the coolant reservoir and brake master cylinder, and fill as needed. • check function of all inte...

  • Page 408

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 1...

  • Page 409

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 410

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 411

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 413: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .412 ▫ prepare for the appointment. . . . . . . . . . . . .412 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .412 ▫ be reasonable with requests ....

  • Page 414

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 415

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 416

    (tty) in the united states, can communicate with the manufacturer by dialing 1–800–380–chry. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewriter users, dial 711 and for voice callers, dial 1-800-8...

  • Page 417

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 418

    To contact nhtsa, you may either call the auto safety hotline toll free at 1–888–327–4236 (tty: 1–800–424– 9153), or go to http://www.Safercar.Gov; or write to: administra- tor, nhtsa, 1200 new jersey avenue, se., west building, washington, d.C. 20590. You can also obtain other infor- mation about m...

  • Page 419

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 420

    All passenger car tires must conform to federal safety requirements in addition to these grades. Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 wou...

  • Page 421

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 423: Index

    Index 10

  • Page 424

    Adding engine coolant (antifreeze) . . . . . . . . . . . .371 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .366 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .296 airbag. . . . . . . . . ....

  • Page 425

    Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238 battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .332 keyless transmitter replacement (rke) . . . . . . . .18 belts, seat . . . . . . ...

  • Page 426

    Child restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 child restraints child seat installation . . . . . . . . . . . . . . . . . . . . .73 install a latch-compatible child restraint . . . . .68 installing child restraints using the vehicle seat belt . . . . . . . . . . . . . . . ...

  • Page 427

    Dealer service. . . . . . . . . . . . . . . . . . . . . . . . . . . .351 defroster, windshield . . . . . . . . . . . . . . . . . . . . . . .80 diagnostic system, onboard . . . . . . . . . . . . . . . . .349 dipsticks automatic transmission . . . . . . . . . . . . . . . . . .379 disposal antifreeze (...

  • Page 428

    Exhaust gas caution . . . . . . . . . . . . . . . . . . . . .78 fails to start . . . . . . . . . . . . . . . . . . . . . . . . . . .225 flooded, starting . . . . . . . . . . . . . . . . . . . . . . .225 fuel requirements . . . . . . . . . . . . . . . . . . . . . .293 oil . . . . . . . . . . . . . . ...

  • Page 429

    Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .298 additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296 capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .399 clean air . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294 cutoff . . . . . ....

  • Page 430

    Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 heated mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . .93 heated seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 heater . . ....

  • Page 431

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .293 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 liftgate (sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . .25 light b...

  • Page 432

    Lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .317 maintenance free battery. . . . . . . . . . . . . . . . . . . .357 maintenance, general . . . . . . . . . . . . . . . . . . . . . .352 maintenance procedures . . . . . . . . . . . . . . . . . . . .352 maintenance schedule . . ...

  • Page 433

    Filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .356 identification logo . . . . . . . . . . . . . . . . . . . . . .354 materials added to . . . . . . . . . . . . . . . . . . . . . .356 recommendation . . . . . . . . . . . . . . . . . . . . . . .354 synthetic . . . . . . . . . . . . ...

  • Page 434

    Recorder, event data . . . . . . . . . . . . . . . . . . . . . . .55 recreational towing . . . . . . . . . . . . . . . . . . . . . . .300 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .294 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 release, hood. . . ....

  • Page 435

    Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .101 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 sentry key® fcc general information . . . . . . . . . . . . . . . . . .15 sentry key (immobilizer) . . . . . . . . . . . . . . . . . . . .13 service assistance ...

  • Page 436

    Synthetic engine oil . . . . . . . . . . . . . . . . . . . . . . .356 tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 temperature control, automatic (atc) . . . . . . . . . .209 temperature gauge, engine coolant . . . . . . . . . . . .155 tilt steering column . . . . . . . ....

  • Page 437

    Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 traction control . . . . . . . . . . . . . . . . . . . . . . . . . .251 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . .299 transaxle automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 ...

  • Page 438

    Wind buffeting. . . . . . . . . . . . . . . . . . . . . . . . . . . .25 window fogging . . . . . . . . . . . . . . . . . . . . . . . . .216 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 windshield def...

  • Page 439

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 440

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 fia t 500 14ff500-126-ac third edition rev 1 printed in u.S.A. Fiat 500