1. DL manuals
  2. Fiat
  3. Automobile
  4. 500 2012
  5. Owner's Manual

Fiat 500 2012 Owner's Manual

Summary of 500 2012

  • Page 1

    Fiat 500 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 2 2012 fia t 500 12ff500-126-af sixth edition rev 1 printed in u.S.A..

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 understanding the featu...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ! How to use this manual . . . . . . . . . . . . . . . . . . 4 ! Warnings and cautions . . . . . . . . . . . . . . . . . . . 6 ! Vehicle identification number . . . . . . . . . . . . . . 6 ! Vehicle modifica...

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owner’s manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important info...

  • Page 9

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Stamped vin location 1 introduction 7.

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . . . . . . 11 ▫ ignition key removal . . . . . . . . . . . . . . . . . . 12 ▫ locking doors with a key . . . . . . . . . . . . . . 13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . 14 ! Sen...

  • Page 12

    ! Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 ! Occupant restraints . . . . . . . . . . . . . . . . . . . . . 27 ▫ lap/shoulder belts . . . . . . . . . . . . . . . . . . . . 31 ▫ lap/shoulder belt untwisting procedure . . . . 36 ▫ seat belts in passenger seating positions ....

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 14

    Ignition key removal 1. Place the shift lever in park (if equipped with an automatic transmission). 2. Turn the ignition switch to the acc/on/run posi- tion. 3. Rotate the key to the off/lock position. 4. Remove the key from the ignition switch lock cylinder. Ignition switch positions 1 — stop (off/...

  • Page 15

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children...

  • Page 16

    Key-in-ignition reminder opening the driver’s door when the key is in the ignition and the ignition switch position is off/lock, sounds a signal to remove the key. Sentry key$ the sentry key# immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not ne...

  • Page 17

    Replacement keys note: only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a sentry key# has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four-digit persona...

  • Page 18

    Remote keyless entry (rke) — if equipped this system allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmit- ter. The rke transmitter does not need to be pointed at the vehicle to activate the system. ...

  • Page 19

    Note: the remote keyless power top function can be used to open the power top to the spoiler position. Opening power top remote function: 1. Open − push and hold the unlock button down on the key fob for a minimum of three seconds to initiate power top open. The roof will stop opening when- ever the...

  • Page 20

    Warning! (continued) • never place any extremities (hands, feet, etc.) near the convertible top components, the upper wind- shield area, the shelf area behind the rear seats, or the convertible top stowage area while raising or lowering the convertible top. • when using the power top button on rke t...

  • Page 21

    General information this device complies with part 15 of fcc rules and with rs-210 of industry canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may...

  • Page 22

    Transmitter battery replacement note: perchlorate material – special handling may apply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate the recommended replacement battery is cr2032. 1. Press the mechanical key release button and release the mechanical key to access the battery case screw located on...

  • Page 23

    2. Rotate the screw located on the side of the key fob using a small screwdriver. 3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 2 ...

  • Page 24

    Door locks the door locks can be manually locked or unlocked from inside the vehicle by using the door handle. If the door handle is pushed a red lock indicator will show on the door handle (indicating locked) when the door is closed, the door will lock. Warning! • do not leave children or animals i...

  • Page 25

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the shift lever. • do not leave the key fob in or near the ...

  • Page 26

    Note: to prevent the key from being locked in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open. A chime will sound as a reminder to remove the key. Automatic door locks — if equipped when enabled, the door locks will lock automati...

  • Page 27

    Warning! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto-down — if equipped the driver’s door...

  • Page 28

    Down automatically. To cancel the auto-down move- ment, operate the switch in either the up or down direction and release the switch. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeti...

  • Page 29

    Warning! • driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are...

  • Page 30

    • all seat belt systems (except the driver’s) include automatic locking retractors (alrs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat — if equipped pl...

  • Page 31

    Ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should always wear their lap and shoulder belts...

  • Page 32

    Warning! (continued) • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • side air ...

  • Page 33

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/shoulder belts all the seating positions in your vehicle are equipped with combination lap/shoulder belts. The belt webbing retractor is designed to lock durin...

  • Page 34

    Warning! (continued) • wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too. • two ...

  • Page 35

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” warning! • a belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your bel...

  • Page 36

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your s...

  • Page 37

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 38

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 39

    Out only the amount of webbing necessary to comfort- ably wrap around the occupant’s mid-section. Slide the latch plate into the buckle until you hear a %click.% automatic locking retractor mode (alr) — if equipped in this mode, the shoulder belt is automatically pre- locked. The belt will still ret...

  • Page 40

    Warning! • the belt and retractor assembly must be replaced if the seat belt assembly automatic locking re- tractor (alr) feature or any other seat belt func- tion is not working properly when checked ac- cording to the procedures in the service manual. • failure to replace the belt and retractor as...

  • Page 41

    Enhanced seat belt use reminder system (beltalert$) beltalert# is a feature intended to remind the driver and front passenger (if equipped with front passenger beltalert#) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted...

  • Page 42

    Seat belt extender if a seat belt is too short, even when fully extended, and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not lon...

  • Page 43

    In addition, the vehicle is equipped with a supplemental driver side knee air bag mounted in the instrument panel below the steering column. Note: these air bags are certified to the federal regulations for advanced air bags. The advanced front air bags are designed to allow the air bags to have dif...

  • Page 44

    And rear passengers sitting next to a window. The sabic are located above the side windows. The trim covering the sabic is labeled srs airbag. This vehicle is equipped with supplemental seat- mounted side air bags (sab). The sab are marked with an air bag label sewn into the outboard side of the fro...

  • Page 45

    Advanced front air bag features the advanced front air bag system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front impact sensors. Warning! • no objects should be placed over or ne...

  • Page 46

    Supplemental seat-mounted side air bags (sab) supplemental seat-mounted side air bags (sab) provide enhanced protection to help protect an occupant during a side impact. The sab are marked with an air bag label sewn into the outboard side of the front seats. When the air bag deploys, it opens the se...

  • Page 47

    Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deploy- ment. The system includes side impact sensors that are cali- brated to deploy the seat-mounted side air bags (sab) and sabic during impacts that require air bag occupant protection. Warning! • you...

  • Page 48

    Warning! (continued) • your vehicle is equipped with sabic air bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require perma- nent attachments (bolts or screws) for installation on the vehicle roof. Do ...

  • Page 49

    Side air bags (sab), and front seat belt pretensioners, as required, depending on the severity and type of impact. Advanced front air bags and supplemental driver side knee air bag are designed to provide additional protec- tion by supplementing the seat belts in certain frontal collisions depending...

  • Page 50

    The orc contains a backup power supply system that may deploy the air bags even if the battery loses power or it becomes disconnected prior to deployment. Also, the orc turns on the air bag warning light in the instrument panel for approxi- mately four to eight seconds for a self-check when the igni...

  • Page 51

    Are possible, based on the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the air bags inflate to their full size. The air bags fully inflate in about 50 to 70 milliseconds. This is about half of the...

  • Page 52

    In about 10 milliseconds. The side air bag moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the side air bag inflates. This especially applies to children. Supplemental side air bag inflatable ...

  • Page 53

    Event, the orc will determine whether to have the enhanced accident response system perform the follow- ing functions: • cut off fuel to the engine. • flash hazard lights as long as the battery has power or until the ignition key is turned off. • turn on the interior lights, which remain on as long ...

  • Page 54

    Customer action customer will see 4. Turn left turn signal switch on. Left turn light is on solid. Right turn light blinks. 5. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is ...

  • Page 55

    If you do have a collision which deploys the air bags, any or all of the following may occur: • the nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or thos...

  • Page 56

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 57

    Air bag warning light you will want to have the air bags ready to inflate for your protection in a collision. The air bag warning light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenan...

  • Page 58

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 59

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and all canadian provinces, require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Childr...

  • Page 60

    The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rearward- facing or forward-facing in the vehicle. Convertible child seats often hav...

  • Page 61

    In the vehicle by the lap/shoulder belt or the latch child restraint anchorage system. Refer to “lower an- chors and tether for children (latch)”. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s s...

  • Page 62

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat. • make sure that the child is upright ...

  • Page 63

    Latch — child seat anchorage system (lower anchors and tether for children) your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tether for children. The latch system provides for the installation of the child restraint without using t...

  • Page 64

    Warning! You should never install latch-compatible child seats so that two seats share a common anchorage. If installing seats in adjacent seating positions, or if your child restraints are not latch-compatible, in- stall the restraints using the vehicle’s seat belts. Installing the latch – compatib...

  • Page 65

    The lower anchorages are round bars which are part of the seat and body structure. They are located at the rear of the seat cushion where it meets the seatback and just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the...

  • Page 66

    Note: • ensure that the tether strap does not slip into the opening between the seatbacks as you remove the slack in the strap. • when using the latch attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach o...

  • Page 67

    Retractor. For additional information on alr, refer to “automatic locking mode” description under “occu- pant restraints.” the chart below defines the seating positions with an automatic locking retractor (alr) or a cinching latch plate. Driver passenger crs lock crs lock first row n/a alr second ro...

  • Page 68

    To attach a child restraint tether strap: • route the tether strap under the head restraint to provide the most direct path for the strap between the anchor and the child seat. • if necessary, move the seat forward to provide better access to the tether anchor. • attach the tether strap hook of the ...

  • Page 69

    Transporting pets air bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or could injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured ...

  • Page 70

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 71

    Warning! (continued) • if you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control blower switch is set at high speed. Do not use the recirculation mode. • if it is necessary to sit in a parked vehicle with the engine running, adjust your ...

  • Page 72

    Air bag warning light the light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned on. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked...

  • Page 73

    Warning! (continued) • never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • check mounting of mats on a regular basis. Al- ways properly reinstall and se...

  • Page 74

    Lights have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight parking for fuel, e...

  • Page 75: Contents

    Understanding the features of your vehicle contents ! Power convertible top — if equipped . . . . . . . 76 ▫ lowering the power top . . . . . . . . . . . . . . . 76 ▫ raising the power top . . . . . . . . . . . . . . . . . 77 ▫ power convertible top relearn proceure . . . . . 78 ▫ wind stop . . . . ...

  • Page 76

    ▫ recline adjustment . . . . . . . . . . . . . . . . . . . . 93 ▫ seat height adjustment . . . . . . . . . . . . . . . . . 94 ▫ ez entry feature . . . . . . . . . . . . . . . . . . . . . . 94 ▫ memory feature . . . . . . . . . . . . . . . . . . . . . . 95 ▫ heated seats — if equipped . . . . . . . ....

  • Page 77

    ▫ to deactivate . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ to resume speed . . . . . . . . . . . . . . . . . . . . . 111 ▫ to vary the speed setting . . . . . . . . . . . . . . . 111 ▫ to accelerate for passing . . . . . . . . . . . . . . . 111 ! Rear park assist — if equipped . . . . . . ....

  • Page 78

    Power convertible top — if equipped on vehicles equipped with a power convertible top, the power convertible top switch is located on the overhead console. The switch contains two buttons. The passenger side button, which is used to open the power top, and the driver side button, which is used to cl...

  • Page 79

    Raising the power top auto close from the convertible top fully open position, push the top close button for approximately one second for the three-quarter open/spoiler position. Push the top close button for approximately one second a second time for the one-quarter open position. Push and hold clo...

  • Page 80

    Warning! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants in a collision. Therefore, it is impor- tant that all occupants wear their seat belts at all times. Death or seriou...

  • Page 81

    This will confirm that the relearn procedure was success- ful. Auto open/close will now be functional. Trunk lid operation will be functional. Remote keyless power top function will be functional. Note: do not interrupt this activity. If the power convertible top does not relearn repeat the procedur...

  • Page 82

    Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night pos...

  • Page 83

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 84

    Power mirrors the power mirror controls are located on the driver’s door trim panel. The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, press the mirror select switch to either the l (left) or r (right) to select the mirror you need ...

  • Page 85

    Spotter mirror — if equipped some models are equipped with a driver’s side spotter mirror. The spotter mirror allows for a greater range of visibility on the driver’s side of the vehicle. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid d...

  • Page 86

    Blue&me™ hands-free communication — if equipped overview windows mobile™-based fiat blue&me™ is a per- sonal telematic system enabling you to use communica- tion and entertainment applications expressly designed for use in the car. The blue&me™ system installed on your car is equipped with a hands-f...

  • Page 87

    You are not required to train the voice recognition system to recognize your voice. This implies that the system is nearly equally performing with different persons, i.E.: the voice recognition system is of the “speaker independent” type. With this system you can also play your favorite music stored...

  • Page 88

    Your mobile phone manually and visually using the steering wheel controls and the instrument panel multi- function display. For further details on the mobile phones supported by blue&me™, refer to section blue&me™ supported mobile phones. To get started with blue&me™ hands-free kit with voice recogn...

  • Page 89

    List or directly pronouncing the phone number, to answer a call and also to answer another incoming phone call. • to interact with blue&me™ you can use either the buttons on the steering wheel or voice commands. With voice recognition, you can perform system func- tions by speaking voice commands, a...

  • Page 90

    • to answer a call — you can answer an incoming call by pressing the main/phone button on the steering wheel. • conference call — you can call another contact while you are engaged in a phone conversation (with bluetooth# phones supporting this option). • call waiting — while engaged in a phone conv...

  • Page 91

    Note: not all mobile phones support the sms text message reader function or automatic phonebook trans- fer via bluetooth#. Consult www.Fiatusa.Com for further information on the list of compatible mobile phones. Message reader functions are managed by the control buttons on the steering wheel or by ...

  • Page 92

    In this way, while you are driving you can play your favorite personal music collections. • ipod# player — see dedicated paragraph under media player functions. The media player enables the following operations: • digital audio playback — you can play all your digital audio files (.Mp3,.Wma,.Wav,.Aa...

  • Page 93

    Warning! • operating certain parts of this system while driv- ing can distract your attention away from the road, and possibly cause an accident or other serious consequences; for this reason certain functions shall be disabled by the blue&me™ system until driving conditions are secure and, if requi...

  • Page 94

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision...

  • Page 95

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 96

    Seat height adjustment the driver’s seat height can be raised or lowered by using a lever, located on the outboard side of the seat. Pump the lever upward to raise the seat height, or pump the lever downward to lower the seat height. Ez entry feature the driver and front passenger seats have an ez e...

  • Page 97

    Lift the seatback upright and push the seat rearward to its locked position once the rear passengers are seated. Memory feature the driver seat also has a memory feature, which can operate in two ways: memory function option 1) — full seat back and track fore/aft position memory: after using the ez ...

  • Page 98

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 99

    To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. The reactive head restraints will automatically return to their normal position following a rear imp...

  • Page 100

    Downward on the head restraint. Refer to “occupant restraints” in “things to know before starting your vehicle” for information on tether routing. To open and close the hood to open the hood, two latches must be released. 1. Pull the bottom of the red hood release lever, located on the left kick pan...

  • Page 101

    2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the engine compartment. Place the hood prop rod in the hole of hood hinge to secure the hood in the ...

  • Page 102

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. Note: the external lights can only be turned on with the ignition in the on/run position. Headlights...

  • Page 103

    High beams with the low beams activated, push the multifunc- tion lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-to-pass you can signal another vehicle with your headlights by lightly pulling the ...

  • Page 104

    Turn signals push the multifunction lever upward to signal a right turn or downward to signal a left turn. The correspond- ing indicator in the instrument cluster will blink to indicate the operation of the turn signal. Note: the indicators will automatically turn off when the turn has been complete...

  • Page 105

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Interior lights the interior light switches are located in the overhead console. The interior lights can be set to three different positions (off/left position, center position, on/right positi...

  • Page 106

    Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is moved into the on/run position. Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below ...

  • Page 107

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 108

    Note: the intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to th...

  • Page 109

    Caution! (continued) • always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Rear windshield wiper rotate the...

  • Page 110

    Rear windshield washer operation push the windshield wiper/washer lever toward the instrument panel to activate the rear washer. Push and hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equi...

  • Page 111

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this war...

  • Page 112

    System can be reactivated by pushing the electronic speed control on/off button and resetting the desired vehicle set speed. To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cru...

  • Page 113

    To resume speed to resume a previously set speed, push the res (+) button and release. Resume can be used at any speed above 20 mph (32 km/h). To vary the speed setting when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. If the button is continually pres...

  • Page 114

    Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so...

  • Page 115

    Rear park assist sensors the four rear park assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles, in the horizontal direction, from approximately 12 in (30 cm) up to 55 in (140 cm) from the ...

  • Page 116

    Audible and visual signals supplied by the rear park assist system. Signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that in- creases as the distance decreases. • emits continu...

  • Page 117

    Failure indications a malfunction of the rear park assist sensors or system is indicated, during reverse gear engagement, by the instrument panel warning icon. The warning icon is illuminated and a message is displayed on the multifunction display (if equipped). Refer to “instrument cluster de- scri...

  • Page 118

    Not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The rear park assist system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/bumper. • objects...

  • Page 119

    Warning! • drivers must be careful when backing up even when using the rear park assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots be- fore backing up. You are responsible for safet...

  • Page 120

    Power sunroof — if equipped the power sunroof roof switch is located in the overhead console. Warning! • never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof s...

  • Page 121

    To open press and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Press the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open...

  • Page 122

    Emergency operation in case of electrical failure the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. I...

  • Page 123

    Electrical power outlets there is a standard 12 volt (13 amp) power outlet, located in the floor console, for added convenience. This power outlet can power mobile phones, electronics and other low power devices. Power is available when the ignition switch is in the on/run or start position. Insert ...

  • Page 124

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 125

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 126

    Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front cupholders rear cupholders 124 understanding the features of your v...

  • Page 127

    Storage glove box compartment the glove box is located on the right side of the instru- ment panel. Pull outward on the door latch to open the glove box. Push the glove box door upward to close it. Passenger seat storage — if equipped some models may be equipped with storage under the front passenge...

  • Page 128

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 129

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defr...

  • Page 130

    Caution! (continued) • do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • keep all objects a safe distance from the window. 128 understanding the features of your vehicle.

  • Page 131: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . . . . . . . 131 ! Instrument cluster . . . . . . . . . . . . . . . . . . . . 132 ! Instrument cluster descriptions . . . . . . . . . . . 133 ! Electronic vehicle information center (evic) . . 144 ▫ evic displa...

  • Page 132

    ▫ technical specifications . . . . . . . . . . . . . . . . 164 ▫ quick guide . . . . . . . . . . . . . . . . . . . . . . . 165 ▫ general information . . . . . . . . . . . . . . . . . . 167 ▫ functions and adjustments . . . . . . . . . . . . . 169 ▫ radio . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 133

    Instrument panel features 1 — side vent 7 — passenger air bag 13 — storage compartment 2 — multifunction lever – light control 8 — glove compartment 14 — shift lever 3 — instrument cluster and warning lights 9 — rear defrost button 15 — sport button 4 — windshield wiper, washer, trip computer 10 — h...

  • Page 134

    Instrument cluster 132 understanding your instrument panel.

  • Page 135

    Instrument cluster descriptions 1. Glow plug light — if equipped the glow plug light will flash during engine oil viscosity sensor measurement in cold weather. During this measurement (up to 10 seconds), the starter will be disabled. If the measured oil viscosity is ok, the light will turn off and t...

  • Page 136

    3. Front fog light indicator — if equipped this indicator will illuminate when the front fog lights are on. 4. Low fuel light when the fuel level reaches approximately 1.0 gal- lon (3.8l) this light will turn on, and remain on until fuel is added. 5. High beam indicator this light indicates that the...

  • Page 137

    9. Air bag warning light this light will turn on for four seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “o...

  • Page 138

    13. Power steering system warning this light is used to manage the electrical warning of the eps (power steering system). Refer to “power steering” in “starting and operating” for further information. 14. Electronic throttle control (etc) light this light informs you of a problem with the electronic...

  • Page 139

    Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fue...

  • Page 140

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 141

    Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the mil after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require to...

  • Page 142

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 143

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. 21. Electronic stability control off (esc off) indicator light this light ...

  • Page 144

    If the abs light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the brake warning light is not on. If the abs light is on, t...

  • Page 145

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “main- taining your vehicle.” follow the warni...

  • Page 146

    27. Fuel gauge / fuel door reminder the fuel door reminder indicates that the fuel filler door is located on the right side of the vehicle. When the ignition switch is in the on/run position, the digital scale will show the level of fuel remaining in the fuel tank. Note: the fuel gauge and range wil...

  • Page 147

    The evic consists of the following: • system status • vehicle information warning message displays • personal settings (customer-programmable features) • outside temperature display • trip computer functions 4 understanding your instrument panel 145.

  • Page 148

    Evic displays evic display manual transmission 1 — temperature indicator 6 — message display 2 — fuel level gauge 7 — coolant temperature gauge 3 — clock 8 — digital speedometer 4 — odometer 9 — ice warning indicator 5 — sport mode 10 — gear shift indicator (gsi) evic display automatic transmission ...

  • Page 149

    Evic control buttons press the menu esc button briefly to access the menu and/or go to next screen or to confirm the required menu option. Press and hold the menu esc button (approxi- mately one second) to return to the main screen. Press the + button to scroll upward through the dis- played menu an...

  • Page 150

    • set date • see radio • speed display • autoclose • units • language • buzzer volume • button volume • daylights (d.R.L.) • hill start • exit menu selecting an option of the main menu without submenu 1. Briefly press the menu esc button to select the main menu option to set. 2. Press the + or – but...

  • Page 151

    3. Briefly press the menu esc button to select the displayed submenu option and to open the relevant setup menu. 4. Press the + or – button (by single presses) to select the new setting for this submenu option. 5. Briefly press the menu esc button to store the new setting and go back to the previous...

  • Page 152

    Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as; trip information, range, fuel consumption, average speed and travel time). Trip button the trip button, located on the right steering column stalk, can be u...

  • Page 153

    Briefly press the menu esc button to go back to the menu screen or press and hold the menu esc (approxi- mately one second) to go back to the main screen without storing settings. Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figur...

  • Page 154

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance travelled this value shows the distance covered since the la...

  • Page 155

    2. Briefly press the menu esc button to go back to the menu screen or press and hold the menu esc (approxi- mately one second) to go back to the main screen without storing settings. Speed beep (speed limit) with this function it is possible to set the car speed limit (mph or km/h); when this limit ...

  • Page 156

    3. Briefly press the menu esc button to go back to the menu screen, or press and hold the menu esc button (approximately one second) to go back to the main screen without storing the settings. Trip b data (trip b on) through this option, it is possible to activate (on) or deactivate (off) the trip b...

  • Page 157

    Note: • the setting will increase or decrease by one unit each time the + or – button is pressed. Press and hold the button to increase/decrease the setting rapidly. Save the setting by briefly pressing the button when you approach the required setting. • briefly press the menu esc button to return ...

  • Page 158

    + or – button to increase/decrease the setting rapidly. Save the setting by briefly pressing the button when you approach the required setting. • briefly press the menu esc button to go back to the menu screen, or press and hold the menu esc button (approximately one second) to go back to the main s...

  • Page 159

    To activate (on) or to deactivate (off) the speed display feature, proceed as follows: 1. Briefly press the menu esc button. “mph”, “km/ h”, then “off” will flash on the display (according to previous setting). 2. Press the + or – button to select display deactivation “off”, “mph” or “km/h”. 3. Brie...

  • Page 160

    2. Press the + or – button to navigate the three sub- menus. 3. Select the required sub-menu and then briefly press the menu esc button. 4. When accessing the “distance” submenu: briefly press the menu esc button. Either “mi” or “km” will appear on the display (according to the previous setting). 5....

  • Page 161

    Language (selecting the language) the messages can be displayed in the following lan- guages: italian, english, german, portuguese, spanish, french, dutch, polish. To set the required language, proceed as follows: 1. Briefly press the menu esc button. The previously set “language” will flash on the ...

  • Page 162

    3. Briefly press the menu esc button to go back to the menu screen, or press and hold the menu esc button (approximately one second) to go back to the main screen without storing the settings. Belt buzzer (buzzer activation for s.B.R. Indication) this function will only be displayed after a fiat gro...

  • Page 163

    3. Briefly press the menu esc button to go back to the menu screen, or press and hold the button (approxi- mately one second) to go back to the main screen without storing the settings. Exit menu this function closes the initial menu screen. Briefly press the menu esc button to go back to the main s...

  • Page 164

    If the radio has blue&me™, refer to the appropriate “blue&me™ user’s manual” for further information. The instructions for use are given below and we recom- mend you to read them carefully. Suggestions road safety please, learn how to use all different radio functions (e.G. Store stations) before be...

  • Page 165

    • clean every cd thoroughly removing any finger marks or dust using a soft cloth. Hold cds by the outside and clean them from the middle outwards. • never use chemicals (e.G. Antistatics or thinners or sprays) for cleaning as they could damage the surface of the cds. • after listening to them place ...

  • Page 166

    • the cd player is capable of reading most compression systems currently in use, following the development of these systems, the reading of all compression for- mats is not guaranteed. Technical specifications the complete system consists of: • two 165 mm diameter midwoofer speakers, one speaker in ...

  • Page 167

    Quick guide radio controls button general functions mode on short button press off long button press tuner am, fm, sat (if equipped) source se- lection short repeated button press a-b-c cycles a, b, c presets for am, fm, sat (if equipped) short repeated button press media cd/aux/media player (if equ...

  • Page 168

    Button general functions mode (information button) song, artist, album, genre, playlist, folder information (if available) in cd, media player and satellite (if so equipped); toggles rbds information in fm menu advanced functions adjustment menu activation: short button press adjustment type selecti...

  • Page 169

    Button radio functions mode 1 2 3 4 5 current radio station storing long button press for memory preset 1 to 5 respectively stored station recall short button press for memory preset 1 to 5 respectively button cd functions mode cd ejection short button press previous/next track play short button pre...

  • Page 170

    • speed volume function: customer selectable auto- matic volume adjustment depending on the car speed • automatic stereo/mono selection cd section • track selection (forward/backward) • fast forward/rewind through tracks • cd display function: display of track number and on mp3 discs (song title, ar...

  • Page 171

    Audio section • mute/pause function • soft mute function • loudness function • graphic 7 band equalizer (if equipped) • separate bass/treble tone adjustment • right/left channel balancing • front/rear fader functions and adjustments turning the car radio on the car radio comes on when the (on/off) b...

  • Page 172

    Mute/pause function press the button briefly to activate the mute function. The volume will gradually decrease and the wording “tuner mute” will be shown on the display (in radio mode) or “cd pause” (in cd mode). Press the button again to deactivate the mute function. The volume will gradually incre...

  • Page 173

    • equalizer — if equipped (activation and selection of factory equalization adjustments) • user equalizer — if equipped (customized equal- ization adjustment) tone adjustment proceed as follows: 1. Press audio button. 2. Press the or button to select “bass” or “treble” in the audio menu. 3. Press th...

  • Page 174

    Fader adjustment proceed as follows: 1. Press audio button. 2. Press the or button to set “fader” in the audio menu. 3. Press the button to increase the sound coming from the rear speakers or the button to increase the sound coming from the front speakers. By pressing the or buttons briefly, the lev...

  • Page 175

    To activate the equalizer, use the audio button or to select one of the adjustments: • “eq user” (adjustment of 7 equalizer bands that can be changed by the user) • “classic” (equalizer preset for optimal classic music sound) • “rock” (equalizer preset for optimal rock and pop music sound) • “jazz” ...

  • Page 176

    The current status of the selected function appears on the display. The functions managed by the menu are: • speech volume • aux audio offset • radio off • sat id • sirius# telephone number • system reset • speed volume • on volume limit press the menu button again to exit the menu function. Speed v...

  • Page 177

    The display shows the function status: • “on volume limit: on” – when the radio is turned on the volume level will be: − if the volume level is equal to or higher than the maximum value, the radio will come on at the maxi- mum volume. − if the volume level is between the minimum and maximum values, ...

  • Page 178

    • “radio off: 20 min” — the radio turns off indepen- dently from the ignition key; the radio remains on for a maximum period of 20 minutes after the key has been turned to the stop position. System reset function this function is used to restore all settings to the factory values. The options are: •...

  • Page 179

    Each time the button is pressed the following bands are selected cyclically: • am, fm or sat (if equipped) each band is highlighted by the corresponding wordings on the display. The radio will be tuned to last station selected on the respective frequency band. Preset buttons the buttons numbered fro...

  • Page 180

    In the desired direction. If the or button is pressed longer, the fast search starts and then stops when the button is released. Stereophonic broadcasters if the incoming signal is weak, the reproduction is automatically switched from stereo to mono. Sirius$ satellite radio — if equipped satellite r...

  • Page 181

    Terms & conditions available at sirius.Com/service terms. Sirius radio u.S. Service only available to those at least 18 years of age in the 48 contiguous united states, d.C., and pr. Service available in canada; see www.Siriuscanada.Ca. Sirius# satellite radio program types program types can be sele...

  • Page 182

    When installed in the customer’s vehicle. To reactivate your service, either call the number listed on the display or visit the provider online. Caution! Neither sirius nor fiat is responsible for any errors in accuracies in the sirius data services or its use in vehicles. Sirius xm and all related ...

  • Page 183

    Cd player introduction this chapter describes the operation of the cd player only. To operate the radio, refer to the description in the “functions and adjustments” chapter. Cd player selection to activate the cd player built into the equipment, proceed as follows: • load a cd with the equipment swi...

  • Page 184

    Press the button with the radio turned on, to activate the motorized cd ejection system. After ejection, the last audio source listened to before playing the cd will be heard. If the cd is not removed from the radio, it will automati- cally be reloaded about 20 seconds later but will not resume play...

  • Page 185

    Beginning. In this case, if you want to play the previous track, press the button twice consecutively. Track fast forward/rewind keep the button pressed down to fast forward the selected track and keep the button pressed down to fast rewind the track. The fast forward/rewind will stop once the butto...

  • Page 186

    • the music files should have the extension “.Mp3” or “.Wma” files with a different extension will not be reproduced. • the sampling frequencies that can be reproduced are: 44.1 khz, stereo (from 96 to 320 kbit/s) – 22.05 khz, mono or stereo (from 32 to 80 kbit/s). • tracks with a variable bit-rate ...

  • Page 187

    Selection of next/previous folder press the button to select a next folder or the button to select the previous folder. The display will show the number of the folder. The folders are selected cyclically. The first folder is selected after the last folder and vice versa. If no other folder/track is ...

  • Page 188

    Cd player the cd does not play the cd is dirty. Clean the cd. The cd is scratched. Try using another cd. The cd can not be loaded a cd is already loaded. Press the button and remove the cd. Mp3 file reading track skips while playing mp3 files the cd is scratched or dirty. The duration of the mp3 tra...

  • Page 189

    Refer to the appropriate blue&me™ radio user’s manual for ipod# or external usb device support capability. Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. 1 — ipod# or external usb de...

  • Page 190

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button will ...

  • Page 191

    Operating instructions — hands-free phone (if equipped) refer to the appropriate blue&me™ user’s manual for further information. Cd/dvd disc maintenance to keep a cd/dvd in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is s...

  • Page 192

    Climate controls the air conditioning and heating system is designed to make you comfortable in all types of weather. Manual heating and air conditioning the manual climate controls consist of a series of rotary dials and one inner push knob. 1. Temperature control rotate this control to regulate th...

  • Page 193

    Note: • continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • the use of the recirculation mode in cold or damp weather could cause windows to fog on the inside, because of moisture buildup inside the veh...

  • Page 194

    The windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • defrost air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. Note: ...

  • Page 195

    Operating tips chart 4 understanding your instrument panel 193.

  • Page 196

    Automatic temperature control (atc) — if equipped • the automatic temperature control (atc) allows the driver to select individual comfort settings. • the system provides set-and-forget operation for op- timum comfort and convenience. • the system can be controlled manually, if desired. The atc syst...

  • Page 197

    2. A/c button press and release to change the current air conditioning (a/c) setting. Performing this function will cause the atc to switch into manual mode. 3. Temperature control up button provides temperature up control. Push the button for warmer temperature settings. 4. Blower control up button...

  • Page 198

    9. Blower control down button there are 12 blower speeds. The blower speed decreases as you press this button. Performing this function will cause the atc to switch into manual mode. 10. Temperature control down button provides temperature down control. Push the button for cooler temperature setting...

  • Page 199

    Note: • it is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • the temperature can be displayed in u.S. Or metric units by selecting the us/m customer-programmabl...

  • Page 200

    The operator can also select the direction of the airflow by selecting one of the following positions. Panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets...

  • Page 201

    Air conditioning (a/c) the air conditioning (a/c) button allows the operator to manually activate or deactivate the air conditioning system. When in a/c mode with the atc set to a cool temperature, dehumidified air flows through the air outlets. If economy mode is desired, press the a/c button to tu...

  • Page 202

    Operating tips window fogging windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning the air conditioning (pressing the a/c button) on will clear the fog. Adjust the temperature cont...

  • Page 203

    Vacation storage anytime you store your vehicle, or keep it out of service (i.E., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air using the high blower setting. This will ensure adequate system lubrication to minimize the possibility o...

  • Page 205: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . . . . . . 207 ▫ manual transmission – if equipped . . . . . . . 207 ▫ automatic transmission – if equipped . . . . . 207 ▫ normal starting . . . . . . . . . . . . . . . . . . . . . 207 ▫ cold weather operation . . . ...

  • Page 206

    ▫ general information . . . . . . . . . . . . . . . . . . 219 ! Driving on slippery surfaces . . . . . . . . . . . . . 220 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 ! Driving through water . . . . . . . . ....

  • Page 207

    ▫ tire loading and tire pressure . . . . . . . . . . 242 ! Tires — general information . . . . . . . . . . . . . 246 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . 246 ▫ tire inflation pressures . . . . . . . . . . . . . . . . 247 ▫ tire pressures for high speed operation . . . 248 ▫ ...

  • Page 208

    ▫ loose fuel filler cap message . . . . . . . . . . . 267 ! Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . 267 ! Recreational towing (behind motorhome, etc.) . . 268 ▫ towing this vehicle behind another vehicle . . 268 206 starting and operating.

  • Page 209

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! Never leave children in the vehicle alone. Leaving unattended children in a vehicle is dangerous for a number of reasons. The child or others could be seri...

  • Page 210

    Cold weather operation to prevent possible engine damage while starting at low temperatures, this vehicle will inhibit engine cranking when the ambient temperature is less than –22° f (–30° c) and the oil temperature sensor reading indicates an engine block heater has not been used. An externally- p...

  • Page 211

    Caution! (continued) • to prevent damage to the starter, do not continu- ously crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After starting the idle speed will automatically decrease as the engine warms up. Manual transmission — if equipped five-spee...

  • Page 212

    Use each gear in numerical order; do not skip a gear. Be sure the transmission is in first gear, not third, when starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears. For steady high...

  • Page 213

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip more than one gear while downshifting or downshift at too high a vehicle speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down t...

  • Page 214

    Warning! It is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or somethin...

  • Page 215

    Vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Shifting from drive to park or reverse should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake...

  • Page 216

    Never attempt to use park while the vehicle is in motion. Apply the parking brake when leaving vehicle in this range. When parking on a level surface, you may place the shift lever in the park position first, and then apply the parking brake. When parking on a hill, apply the parking brake before pl...

  • Page 217

    Warning! (continued) • it is dangerous to move the shift lever out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or som...

  • Page 218

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 219

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can result in severe transmission damage. Refer to “recre- ational towing” in “starting and operating” and “towing a disabled vehicle” in what to do in emergencies” for further information. Drive ...

  • Page 220

    Park, reverse, and neutral will continue to oper- ate. Limp home mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission. In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the following step...

  • Page 221

    Operation when the shift lever is in the autostick# position (to the left of the drive position), it can be moved forward and rearward. This allows the driver to manually select the transmission gear being used. Moving the shift lever forward (-) triggers a downshift, and moving it rearward (+) an u...

  • Page 222

    • if a downshift would cause the engine to over-speed, that shift will not occur until it is safe for the engine. An audible beep will sound if an inappropriate gear is selected. • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • mostly the transmission wi...

  • Page 223

    Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precau- tions shoul...

  • Page 224

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following caution and warning before doing so. Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the...

  • Page 225

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving thr...

  • Page 226

    Warning! Continued operation with reduced or no power steer- ing assist could pose a safety risk to yourself and others. Service should be obtained as soon as pos- sible. Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave manual tra...

  • Page 227

    From the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A...

  • Page 228

    Sport mode manual transmission – if equipped the sport mode increases steering feedback to the driver with slight increases in effort and throttle pedal-to-engine response. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited cornering. 1. To...

  • Page 229

    Automatic transmission – if equipped the sport mode increases steering feedback to the driver with slight increase in effort and changes the transmis- sion shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired...

  • Page 230

    Brake system in the event power assist is lost for any reason (for example; repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly more than that required with the power system operating. If either the front or...

  • Page 231

    Warning! • pumping the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physics f...

  • Page 232

    System (abs), brake assist system (bas), traction con- trol system (tcs), hill start assist (hsa), and electronic stability control (esc). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as esc. Anti-lock brake system (abs...

  • Page 233

    Warning! (continued) • the bas cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplan- ing. • the capabilities of a bas-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the u...

  • Page 234

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 2.5% (manual transmission) or 7% grade or greater (automatic transmission) hill. • gear selection matches vehicle uphill direction (i.E., vehicle in neutral (man...

  • Page 235

    Esc applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • understeer - when the vehicle is turning less than appropriate for the steering wheel po...

  • Page 236

    Warning! The electronic stability control (esc) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very s...

  • Page 237

    To turn esc on again, momentarily press the switch again. This will restore the normal esc on mode of operation. Note: to improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the partial off mode by pressing the ...

  • Page 238

    Malfunction indicator light begins to flash during accel- eration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. Note: • the esc activation/malfunction indicator light and the esc off indicator light co...

  • Page 239

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 240

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards & ....Blank....& = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215...

  • Page 241

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 242

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 243

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire pressure cold tire inflation pressure is defined as the tire pressure after ...

  • Page 244

    Tire loading and tire pressure tire placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar. Tire and loading information placard this placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total wei...

  • Page 245

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 246

    5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult th...

  • Page 247

    5 starting and operating 245.

  • Page 248

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 249

    Warning! (continued) • unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns...

  • Page 250

    Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pr...

  • Page 251

    Warning! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-ply tires warning! C...

  • Page 252

    Warning! (continued) • temporary use spare tires have limited tread life. When the tread is worn to the tread wear indica- tors, the temporary use spare tire needs to be replaced. • be sure to follow the warnings which apply to your spare. Failure to do so could result in spare tire failure and loss...

  • Page 253

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and d...

  • Page 254

    Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style • tire pressure • distance driven warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can resul...

  • Page 255

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 256

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • use security chain company (scc) scc z6 low profile or equivalent chains on 185/55r15 tires only. • because of restricted chain clearance between tires and other suspension components, it is important that only c...

  • Page 257

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns. These effects can be reduced by timely...

  • Page 258

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kpa) for every 12° f (6.5° c). This means that when the o...

  • Page 259

    For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68° f (20° c) and the measured tire pressure is 27 psi (186 kpa), a temperature drop to 20° f (-7° c) will decrease the tire pressure to approxima...

  • Page 260

    Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pressure. • driving on a significantly under-inflated tire causes the tire to overheat ...

  • Page 261

    • four tire pressure monitoring sensors • tire pressure monitoring telltale light tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, an audible chime will be activated, and the “check tire pressure” text message wil...

  • Page 262

    5. Using wheels/tires not equipped with tpm sensors. Note: your vehicle is equipped with a compact spare wheel and tire assembly. 1. The compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not monitor the tire pressure in the compact spare tire. 2. If you ins...

  • Page 263

    • this device must accept any interference received, including interference that may cause undesired operation. The tire pressure sensors are covered under one of the following licenses: united states . . . . . . . . . . . . . . . . . . . Mrxc4w4ma4 canada. . . . . . . . . . . . . . . . 2546a-c4w4ma...

  • Page 264

    The manufacturer supports the use of reformulated gaso- line. Properly blended reformulated gasoline will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, ...

  • Page 265

    To recover from a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank • change the engine oil • replace the fuel filter and oil filter • disconnect the battery to reset the engine controller long term adaptive memory more extensive repairs will be require...

  • Page 266

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emission control system. • an out-of-tune engine, or certain fuel or ignition malfu...

  • Page 267

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such ...

  • Page 268

    Adding fuel fuel filler cap (gas cap) the gas cap is located on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is the correct one for this vehicle. Caution! • damage to the fuel system or emission control system could result from using an improper f...

  • Page 269

    Warning! • never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • never add fuel when the engine is running. It may cause the mil to turn on and could cause a fire. • a fire may result if gasoline is pumped into a portable container tha...

  • Page 270

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission automatic transmission flat tow none transmission in neutral not allowed dolly tow front ok ok rear not allowed not allowed on trailer all ok ok note: ve...

  • Page 271: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . . . . . . . 271 ! If your engine overheats . . . . . . . . . . . . . . . . 271 ! Tirefit kit . . . . . . . . . . . . . . . . . . . . . . . . . 272 ▫ tirefit storage . . . . . . . . . . . . . . . . . . . . . 273 ▫ tirefi...

  • Page 272

    ! Towing a disabled vehicle . . . . . . . . . . . . . . . 299 ▫ with ignition key . . . . . . . . . . . . . . . . . . . . 299 ▫ without the ignition key . . . . . . . . . . . . . . 300 ! Enhanced accident response system . . . . . . . 301 270 what to do in emergencies.

  • Page 273

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 274

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 275

    Tirefit storage the tirefit kit is located under the front driver’s seat. Tirefit kit components and operation 1. Sealant bottle 2. Deflation button 3. Pressure gauge 4. Power button 5. Mode select knob 6. Sealant hose (clear) 7. Air pump hose (black) 8. Power plug using the mode select knob and hos...

  • Page 276

    Selecting sealant mode turn the mode select knob (5) to this position to inject the tirefit sealant and to inflate the tire. Use the sealant hose (clear hose) (6) when selecting this mode. Using the power button push and release the power button (4) once to turn on the tirefit kit. Push and release ...

  • Page 277

    • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tirefit kit. • you can use the tirefit air pump to inflate bicycle tires. The kit also comes with two needles, located in the accessory storage compartment (on the bottom of the air pump) for inf...

  • Page 278

    Warning! (continued) − if you are unsure of the condition of the tire or the wheel. • keep tirefit away from open flames or heat source. • a loose tirefit kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tirefit kit in the place provided. Fa...

  • Page 279

    Sealing a tire with tirefit (a) whenever you stop to use tirefit: 1. Pull over to a safe location and turn on the vehicle’s hazard warning flashers. 2. Verify that the valve stem (on the wheel with the deflated tire) is in a position that is near to the ground. This will allow the tirefit hoses (6) ...

  • Page 280

    (c) injecting tirefit sealant into the deflated tire: • always start the engine before turning on the tire- fit kit. Note: manual transmission vehicles must have the parking brake engaged and the shift lever in neutral. • after pressing the power button (4), the sealant (white fluid) will flow from ...

  • Page 281

    1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 sec- onds). As the sealant flows through the sealant hose (6), the pressure gauge (3) can read as high as 70 psi (5 bar). The pressure gauge (3) will decrease quickly from ap- proximately 70 psi ...

  • Page 282

    Caution! • the metal end fitting from power plug (8) may get hot after use, so it should be handled carefully. • failure to reinstall the cap on the fitting at the end of the sealant hose (6) can result in sealant con- tacting your skin, clothing, and the vehicle’s inte- rior. It can also result in ...

  • Page 283

    3. Uncoil the air pump hose (7) (black in color) and screw the fitting at the end of hose (7) onto the valve stem. 4. Check the pressure in the tire by reading the pressure gauge (3). If tire pressure is less than 19 psi (1.3 bar) , the tire is too badly damaged. Do not attempt to drive the vehicle ...

  • Page 284

    2. Locate the round sealant bottle release button in the recessed area under the sealant bottle. 3. Press the sealant bottle release button. The sealant bottle (1) will pop up. Remove the bottle and dispose of it accordingly. 4. Clean any remaining sealant from the tirefit housing. 5. Position the n...

  • Page 285

    Warning! (continued) • the jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack location the jack and jack-handle are stowed in...

  • Page 286

    Spare tire removal the spare tire is stowed to the underbody below the cargo area. 1. Remove the plug located in the rear cargo area. 2. Fit the wrench tool over the drive nut. Use the wrench to rotate the nut counterclockwise until the spare is on the ground with enough slack in the cable to allow ...

  • Page 287

    Caution! The winch mechanism is designed for use with the jack wrench tool only. Use of an air wrench or other power tools is not recommended and they can dam- age the winch. 3. Pull the spare tire out from under the vehicle. Spare tire 6 what to do in emergencies 285.

  • Page 288

    4. When the spare is clear, remove the knob or plastic molded nut by rotating it counter-clockwise. 5. Tilt the retainer at the end of the cable and pull it through the center of the wheel. Plastic molded nut retainer 286 what to do in emergencies.

  • Page 289

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 290

    Warning! (continued) • turn on the hazard warning flashers. • block the wheel diagonally opposite the wheel to be raised. • set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse. • never start or run the engine with the vehicle on a jack. • do not l...

  • Page 291

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the scissors jack and tool bag from under the driver’s seat. 2. Loosen, but do not remove, the wheel bolts by turning them to the left one turn whil...

  • Page 292

    Do not raise the vehicle until you are sure the jack is securely engaged. 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to th...

  • Page 293

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 4. Using the swivel wrench, raise the vehicle by turning the jack screw to the right. Raise the vehicle only unt...

  • Page 294

    Note: the wheel cover is held on the wheel by the wheel bolts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel bolts. 6. Install the spare wheel and wheel bolts with the cone shaped end of the bolt...

  • Page 295

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 11. Check the spare tire pressure as soon as possible. Correct the tire pressure as required. Spare tire stowage reverse instr...

  • Page 296

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Caution! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 volts or damage to the battery, starter motor, alternator or el...

  • Page 297

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be s...

  • Page 298

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper c...

  • Page 299

    8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. If frequent jump-starting is required to start your vehicle, you should have...

  • Page 300

    Note: if your vehicle is equipped with traction con- trol or electronic stability control (esc), turn the system off before attempting to “rock” the vehicle. Caution! • when “rocking” a stuck vehicle by moving be- tween drive (automatic transmission) or 1st gear (manual transmission) and reverse, do...

  • Page 301

    3. Turn the ignition switch to the on/run position without starting the engine. 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar tool, push and hold the override release lever in. 6. Move the shift lever into the neutral position. 7. The vehicle may the...

  • Page 302

    Manual transmission • vehicle can be flat towed (all four wheels on the ground) with the transmission in neutral. • vehicle can be towed with the front wheels elevated. • vehicle can be towed on a flatbed truck (all wheels off the ground). All transmissions if it is necessary to use the accessories ...

  • Page 303

    Override the system. The ignition key must be in the on/run position to use the override lever. Caution! Failure to follow these towing methods can cause severe transmission damage. Such damage is not covered by the new vehicle limited warranty. Enhanced accident response system in the event of an i...

  • Page 304

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 305: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 1.4l . . . . . . . . . . . . . 305 ! Onboard diagnostic system – obd ii . . . . . . . 306 ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306 ! Replacement parts . . . . . . . . . . . . ....

  • Page 306

    ▫ manual transmission – if equipped . . . . . . . 329 ▫ automatic transmission – if equipped . . . . . 329 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 330 ▫ convertible top care – if equipped . . . . . . . 336 ! Fuses . . . . . . . . . . . . . ...

  • Page 307

    Engine compartment — 1.4l 1 — engine coolant reservoir 5 — battery 2 — engine oil dipstick 6 — air cleaner filter 3 — brake fluid reservoir 7 — engine oil fill 4 — front distribution unit (fuses) 8 — washer fluid reservoir 7 maintaining your vehicle 305.

  • Page 308

    Onboard diagnostic system – obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 309

    For states that require an inspection and mainte- nance (i/m), this check verifies the “malfunction indicator light (mil)” is functioning and is not on when the engine is running, and that the obd ii system is ready for testing. Normally, the obd ii system will be ready. The obd ii system may not be...

  • Page 310

    If your obd ii system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your obd ii system to update. A rech...

  • Page 311

    Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. Maintenance procedures the pages tha...

  • Page 312

    Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Do ...

  • Page 313

    Engine oil selection for best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are api cer- tified and meet the requirements of chrysler material standard ms-6395. American petroleum institute (api) engine oil id...

  • Page 314

    Engine oil filler cap location, refer to “engine compart- ment” in “maintaining your vehicle” for further information. Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter c...

  • Page 315

    Warning! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compa...

  • Page 316

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 317

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 318

    Protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system sealers, stop leak products, s...

  • Page 319

    From a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Make sure that they are not frozen to the glass before turning them on to avoid damaging the blade. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: li...

  • Page 320

    3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade an...

  • Page 321

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 322

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • damage to the catalytic converter can r...

  • Page 323

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 324

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check...

  • Page 325

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use wi...

  • Page 326

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: mixing engine coolant (antifreeze) types is not recommended and can result in cooling system dama...

  • Page 327

    Rules for your community. To prevent ingestion by ani- mals or children do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills i...

  • Page 328

    • check the coolant freeze point in the radiator and in the coolant expansion bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant expansion bottle must also be protected against freez- ing. • if frequent engine coolant (antifreeze) additions are required, the cool...

  • Page 329

    Brake master cylinder the fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “brake warning light” is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to ...

  • Page 330

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 331

    Manual transmission – if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 332

    Fluid. No chemical flushes should be used in any trans- mission; only the approved lubricant may be used. Special additives automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the ...

  • Page 333

    The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes of corrosio...

  • Page 334

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. Special care • if you drive on salted or dusty...

  • Page 335

    Wheel and wheel trim care all wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use mopar# wheel cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel ...

  • Page 336

    Your leather upholstery can be best preserved by regular cleaning with a damp, soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar# total clean ...

  • Page 337

    Quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument panel cover the instrument p...

  • Page 338

    Seat belt maintenance do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the seat belts from the car to ...

  • Page 339

    Washing hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred. Caution! Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force wat...

  • Page 340

    Fuses interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Cavity vehicle fuse number mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 5 amp tan front and rear ceiling lights trunk and door court...

  • Page 341

    Cavity vehicle fuse number mini fuse description 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp brown left low beam, headlamp leveling 9 f50 7.5 amp brown airbag 10 f51 5 amp tan car radio switch, climate control system, stop light, clutch cavity vehicle fuse number mini fuse description 1...

  • Page 342

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Cav...

  • Page 343

    Cavity maxi fuse mini fuse description f08 30 amp green blower motor f09 10 amp red powertrain f10 10 amp red horn f11 15 amp blue powertrain f11 10 amp red powertrain (multi- air – if equipped) f14 5 amp tan high beam (shut- ter) f15 15 amp blue cigar lighter f16 7.5 amp brown transmission cavity m...

  • Page 344

    Cavity maxi fuse mini fuse description f24 7.5 amp brown stability control system f30 15 amp blue fog lamps f82 30 amp green sunroof/ convertible top f84 10 amp red transmission f85 15 amp blue rear defroster, heated mirrors f87 5 amp tan lights f90 5 amp tan heated mirrors vehicle storage if you ar...

  • Page 345

    Replacement bulbs interior lights bulb type overhead lamp . . . . . . . . . . . . . . . . . . . . . . . . C5w courtesy lamp . . . . . . . . . . . . . . . . . . . . . . . . W5w exterior lights bulb type front low and high beam headlamp. . . . . . . . . Hir2 front parking/daytime running lamps. . . . ...

  • Page 346

    Front turn signal, parking and daytime running lamps 1. Turn the steering wheel completely to the left or right. 2. Open the wheel housing access door. 3. Remove the plastic cap from the back of the lamp housing. 4. Rotate bulb/socket counter-clockwise. 5. Remove the bulb and replace as needed. 6. I...

  • Page 347

    Front/rear side marker lamps 1. Remove portion of the wheel liner to allow hand access to side marker lamp. 2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing. 3. Pull the bulb from the socket and insert the replace- ment bulb. 4. Install the bulb an...

  • Page 348

    3. Unsnap backplate and separate from the lamp hous- ing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted stop lamp (chm...

  • Page 349

    Fluid capacities u.S. Metric fuel (approximate) 10.5 gallons 40 liters engine oil with filter 1.4 liter engine 4 quarts 4 liters cooling system 1.4 liter engine (mopar# antifreeze/engine coolant 10 year/152,000 mile formula or equivalent) — with manual transmission 4.6 quarts 4.4 liters 1.4 liter en...

  • Page 350

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant mopar# antifreeze/coolant 10 year/152,000 mile formula oat (or- ganic additive technology) or equivalent meeting the requirements of chrysler material standard ms-12106. Engine oil use api certifi...

  • Page 351

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped mopar# c635 ddct/mtx transmission fluid automatic transmission – if equipped mopar# aw-1 transmission fluid brake master cylinder mopar# dot 3, sae j1703 should be used. If dot 3, sae j1703 brake fluid is not avail...

  • Page 353: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . . . . . . . 352 ▫ required maintenance intervals . . . . . . . . . . 353 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 354

    Maintenance schedule the scheduled maintenance services listed in this manual must be done at the times or mileages specified to protect your vehicle warranty and ensure the best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating condition...

  • Page 355

    At each stop for fuel • check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the add or min mark. • check the w...

  • Page 356

    8,000 miles (13,000 km) or 6 months maintenance service schedule included in the maintenance program ❏ change the engine oil and engine oil fil- ter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 8,000 miles (13 000 km). Odometer reading date repair order #...

  • Page 357

    24,000 miles (39,000 km) or 18 months maintenance service schedule included in the maintenance program ❏ change the engine oil and engine oil fil- ter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 24,000 miles (39 000 km). Odometer reading date repair orde...

  • Page 358

    32,000 miles (52,000 km) or 24 months maintenance service schedule included in the maintenance program ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 32,000 miles (52 000 km). ❏ inspect exhaust system. ❏ replace...

  • Page 359

    40,000 miles (65,000 km) or 30 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 40,000 miles (65 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 360

    56,000 miles (91,000 km) or 42 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 56,000 miles (91 000 km). Odometer reading date repair order # dealer code signature, authorized ...

  • Page 361

    72,000 miles (117,000 km) or 54 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 72,000 miles (117 000 km). Odometer reading date repair order # dealer code signature, authorize...

  • Page 362

    88,000 miles (143,000 km) or 66 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer reading date repair order # dealer code signature, authorize...

  • Page 363

    104,000 miles (169,000 km) or 78 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 104,000 miles (169 000 km). Odometer reading date repair order # dealer code signature, authori...

  • Page 364

    120,000 miles (195,000 km) or 90 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 120,000 miles (195 000 km). Odometer reading date repair order # dealer code signature, authori...

  • Page 365

    136,000 miles (221,000 km) or 102 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 136,000 miles (221 000 km). Odometer reading date repair order # dealer code signature, author...

  • Page 366

    152,000 miles (247,000 km) or 114 months maintenance service schedule ❏ change the engine oil and engine oil filter. ❏ rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). ❏ flush and replace engine coolant. ❏ replace the timing belt. Odo...

  • Page 367

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • failure to properly inspect and mai...

  • Page 369: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 ▫ prepare for the appointment . . . . . . . . . . . 369 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . 369 ▫ be reasonable with r...

  • Page 370

    ! Department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . . . . . . . . . 374 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 374 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . 375 ▫ temperature grades . . . . . . . . . . . . . . . . . . 37...

  • Page 371

    Suggestions for obtaining service for your vehicle prepare for the appointment if you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. ...

  • Page 372

    This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • if for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • if ...

  • Page 373

    Service contract you may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufactur...

  • Page 374

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 375

    West building, washington, d.C. 20590. You can also obtain other information about motor vehicle safety from http://www.Safercar.Gov. In canada if you believe that your vehicle has a safety defect, you should contact the customer service department immedi- ately. Canadian customers who wish to repor...

  • Page 376

    • owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific fiat group automobiles vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safe...

  • Page 377

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 379: Index

    Index 10

  • Page 380

    Adding engine coolant (antifreeze) . . . . . . . . . . 323 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 adding washer fluid . . . . . . . . . . . . . . . . . . . . . 318 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . 263 air cleaner, engine (engine air cle...

  • Page 381

    B-pillar location . . . . . . . . . . . . . . . . . . . . . . . . 242 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 jump starting . . . . . . . . . . . . . . . . . . . . . . . 293 keyless transmitter replacement (rke) . . . . . 20 belts, seat . . . . . . . . . . . . . . ....

  • Page 382

    Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . 261 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 climate control . . . . . . . . . . . . . . . . . . . . . . . . . 190 clutch . . ...

  • Page 383

    Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . 312 door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 door locks, automatic . . . . . . . . . . . . . . . . . . . . 24 downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 driving on slippery surface...

  • Page 384

    Oil selection . . . . . . . . . . . . . . . . . . . . . . . . 311 oil synthetic . . . . . . . . . . . . . . . . . . . . . . . . 312 overheating . . . . . . . . . . . . . . . . . . . . . . . . 271 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 temperature gauge . . . . . . . . . ....

  • Page 385

    Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 octane rating . . . . . . . . . . . . . . . . . . . . . . . 261 requirements . . . . . . . . . . . . . . . . . . . . . . . 261 tank capacity . . . . . . . . . . . . . . . . . . . . . . . 347 fuel system caution . . . . . . . . . . ....

  • Page 386

    Infant restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 57 information center, vehicle . . . . . . . . . . . . . . . . . 144 instrument cluster . . . . . . . . . . . . . . . . . . . . . . . 133 instrument panel and controls . . . . . . . . . . . . . . 131 instrument panel cover . . . . ...

  • Page 387

    High beam indicator . . . . . . . . . . . . . . . . . . 134 low fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 134 malfunction indicator (check engine) . . . . . . 138 oil pressure . . . . . . . . . . . . . . . . . . . . . . . . 138 park . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 388

    New vehicle break-in period . . . . . . . . . . . . . . . . 67 occupant restraints . . . . . . . . . . . . . . . . . . . . . 46,52 occupant restraints (sedan) . . . . . . . . . . . 27,44,46,50 octane rating, gasoline (fuel) . . . . . . . . . . . . . . 261 odometer . . . . . . . . . . . . . . . . . ....

  • Page 389

    Preparation for jacking . . . . . . . . . . . . . . . . . . . . 287 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . 249 radio (sound systems) . . . . . . . . . . . . . . . . . . . . 161 radio operati...

  • Page 390

    Seat belts (sedan) . . . . . . . . . . . . . . . . . . . . . . . . 27 seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 91 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 selection of oil . . . ...

  • Page 391

    Stuck, freeing . . . . . . . . . . . . . . . . . . . . . . . . . . 297 sun roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 supplemental restraint system - airbag . . . . . . . . 40 synthetic engine oil . . . . . . . . . . . . . . . . . . . . . . 312 tachometer . . . . . . . . . ...

  • Page 392

    Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 disabled vehicle . . . . . . . . . . . . . . . . . . . . . 299 recreational . . . . . . . . . . . . . . . . . . . . . . . . 268 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . 267 transaxle automatic . . . . ...

  • Page 393

    Water driving through . . . . . . . . . . . . . . . . . . . . . 221 wheel and wheel trim . . . . . . . . . . . . . . . . . . . . 333 wheel and wheel trim care . . . . . . . . . . . . . . . . 333 wind buffeting . . . . . . . . . . . . . . . . . . . . . . . 26,119 window fogging . . . . . . . . . . . ...

  • Page 394

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 395

    Fiat 500 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 2 2012 fia t 500 12ff500-126-af sixth edition rev 1 printed in u.S.A..