1. DL manuals
  2. Fiat
  3. Automobile
  4. 500e
  5. Owner's Manual

Fiat 500e Owner's Manual

Other manuals for 500e: User Manual

Summary of 500e

  • Page 1

    O w n e r ’ s m a n u a l 2 0 1 6 fiat ® 500e.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 䡵 vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new fiat 500e. Be assured that your 500e represents an elegant marriage of technology and italian styling that is as good for the environment as is fun to drive! This owner’s manual has been prepared with the assis- tance of service and engineering spec...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cautions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 important vehicle information . . . . . . .12 ▫ high voltage battery . . . . . . . . . . . . . . . . . . . .12 䡵 500e electric vehicle features . . . . . . . . .14 ▫ audible pedestrian warning system . . . . . . . . .14 ▫ single-speed transmissi...

  • Page 12

    ▫ vehicle charge indicators. . . . . . . . . . . . . . . . .27 䡵 a word about your keys . . . . . . . . . . . . .31 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .31 ▫ locking doors with a key. . . . . . . . . . . . . . . .33 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .33 ...

  • Page 13

    䡵 liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 䡵 occupant restraint systems . . . . . . . . . .44 ▫ important safety precautions . . . . . . . . . . . . . .44 ▫ seat belt systems . . . . . . . . . . . . . . . . . . . . . .46 ▫ supplemental restraint system (srs) . . . . . . . ....

  • Page 14

    Important vehicle information your 500e operates entirely on electricity stored in the high voltage battery. Unlike a conventional vehicle or hybrid there is no internal combustion engine. Battery electric vehicles have unique operating characteristics that you should become familiar with to ensure ...

  • Page 15

    Lithium-ion batteries provide the following benefits: • lithium-ion batteries are much lighter than other types of rechargeable batteries of the same size. • lithium-ion batteries hold their charge; they only lose approximately 3 percent of their charge per month. • lithium-ion batteries have no mem...

  • Page 16

    • maximize driving range • maximize the life expectancy of the high voltage battery note: • during vehicle start up and shut down a clicking noise may be heard from within the vehicle. When the ignition key is turned to the on position, the high voltage battery contactors inside the battery are clos...

  • Page 17

    The audible warning system uses an in-car sound syn- thesizer with a speaker located in the underhood com- partment. The warning system is automatically activated when selecting drive or reverse. In drive range, the system will remain active until the vehicle reaches a speed of approximately 22 mph ...

  • Page 18

    Note: the engagement of the e-park can be heard when there is no noise in the interior of the vehicle, this is a normal condition. Climate control (hvac system) your 500e is equipped with an automatic temperature control (atc) hvac system. This hvac system utilizes a humidity sensor, cabin sensor, a...

  • Page 19

    Charging from your phone. You can also turn on your vehicle’s climate control system remotely. The app pro- vides the following features: • monitor battery charge level • display available driving distance • check charging status • remotely activate vehicle climate control system • unlock and lock d...

  • Page 20

    Once in the registration website, you will need to enter your vehicle’s vin and connectivity id. The connectivity id is found in the vehicle’s instrument cluster. To locate the connectivity id follow the steps below: 1. Push the menu button on the instrument cluster. 2. Choose “settings” and scroll ...

  • Page 21

    Electric system operation level 1 charging (120v — requires nema 5–15 outlet) level 1 charging is done by using a conventional 120 volt ac grounded receptacle along with the nema 5–15 electric vehicle supply equipment (evse) that comes standard with your vehicle. Refer to “vehicle charging cord” for...

  • Page 22

    Charge times the following factors determine the time it takes to charge the high voltage battery: • the high voltage battery’s current state of charge • what level evse is being used (level 1 – 120v or level 2 – 240v) • ambient temperature note: • the charging times are estimates based on a com- pl...

  • Page 23

    Note: the evse charge cord is used for level 1 charging only. Sae j1772 charge receptacle your vehicle uses an industry standard sae j1772 charge receptacle (vehicle’s inlet) for both ac level 1 (120v) and ac level 2 (240v) charging. Note: the charge receptacle door locks and unlocks with the vehicl...

  • Page 24

    Evse operation and status information indicator description 1 — ac indicator led green indicates ready red indicates a fault indicator description 2 — fault indicator led green indicates ready red indicates a fault 3 — charge level indicator led’s all on indicates system ready and not charging led’s...

  • Page 25

    Ac led fault indica- tor led charge level indicator led’s time • • • o o o 1.5 sec • • • • o o 3.0 sec • • • • • o 4.5 sec • • • • • • 6.0 sec if the self test is successful the ac led, the fault indicator led and the four charge level led’s will turn solid green. The evse led’s will be used to indi...

  • Page 26

    Ac led fault indica- tor led charge level indicator led’s time • • • o o o 1.0 sec • • • • o o 2.0 sec • • • • • o 3.0 sec • • • • • • 4.0 sec refer to the level 1 user manual for any additional information on its use or operation. Charging the high voltage battery 1. Put the vehicle in park. 2. Tur...

  • Page 27

    4. Uncoil the entire length of the evse (charge cord). 5. Plug the evse into a standard 120v ac outlet that is properly grounded. It is recommended that the evse is connected to an ac outlet on a circuit which is not electrically loaded by other devices. Extension cords may not be used. Note: all of...

  • Page 28

    8. When charging is complete, or the vehicle needs to be unplugged, remove the evse by pushing the button on the charge connector and pull firmly to remove it from the charge receptacle. 9. Close the charge receptacle door. Note: • in the event of an error in the charging process, the ac power to th...

  • Page 29

    • keep the door for the charge receptacle closed when not in use. Vehicle charge indicators instrument cluster high voltage battery gauge there is a battery gauge indicator located on the instru- ment cluster. The battery gauge will display, with pro- gressive color indication, the current state of ...

  • Page 30

    Charge low and limited power messages the state of charge is monitored during normal opera- tion. If the state of charge reaches certain thresholds the following messages will also be displayed on the cluster: • charge low — displayed at 17% (warning displayed for six seconds). • charge low — displa...

  • Page 31

    Note: the limited power mode can also be activated if the high voltage battery temperature is too high or too low. Note: at 0% state of charge or below the following features will be disabled if in use: • heated seats • electronic speed control • climate controls instrument panel state of charge ind...

  • Page 32

    The state of charge indicator represents the current state of charge for the high voltage battery. The state of charge indicator lights quickly to identify the battery state of charge while the vehicle is being charged. Each light represents the battery’s current percentage of charge. Note: in the e...

  • Page 33

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key, simply push the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 34

    Warning! • before exiting a vehicle, always apply the parking brake, place the transmission into park, and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children...

  • Page 35

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle u...

  • Page 36

    Note: a key which has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. If the vehicle security light is on after the key is turned to the on/run position, it indicates that there is a problem with the electronics. Cau...

  • Page 37

    1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired op- eration. Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to o...

  • Page 38

    If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle security alarm will remain armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the vehicle security alarm. Remote keyless entry (rke) — if equip...

  • Page 39

    Within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote key unlock, driver door/all doors 1st press this feature lets you program the system to unlock either the driver’s doo...

  • Page 40

    3. Take out the battery case. Remove and replace the battery observing its polarity. 4. Refit the battery case inside the key fob and turn the screw to lock it into place. Key fob screw location battery case removed 38 things to know before starting your vehicle.

  • Page 41

    General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This devic...

  • Page 42

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of an collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before e...

  • Page 43

    Power door locks — if equipped a power door lock switch is incorporated into the driver door handle. Push or pull the handle to lock or unlock the doors and liftgate. If the driver’s door handle is pushed a red lock indicator will show on the driver’s door handle (indicating locked) when the door is...

  • Page 44

    To change the setting proceed as follows: 1. Briefly push the menu button to enter the menu screen. 2. Push the up or down button to highlight “auto door locks”. Push the menu button, use the up or down buttons to turn setting on or off. 3. Briefly push the menu button to go back to the menu screen,...

  • Page 45

    Auto-down the driver’s door window switch has an auto-down fea- ture. Push the window switch for approximately one second, release, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Wind buffetin...

  • Page 46

    Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. Occupant restraint systems some of the most important safety features in your vehicle are the restraint ...

  • Page 47

    2. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. (refer to “child restraints”) 3. Children that are not big enough to wear the vehicle seat belt properly (refer...

  • Page 48

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 49

    The seat belt reminder light will turn on and remain on until both outboard front seat belts are buckled. The outboard front passenger seat beltalert is not active when an outboard front passenger seat is unoccupied. Beltalert warning sequence the beltalert warning sequence is activated when the veh...

  • Page 50

    Note: if beltalert has been deactivated and the driver or outboard front seat passenger (if equipped with out- board front passenger seat beltalert) is unbuckled the seat belt reminder light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled. Lap/sho...

  • Page 51

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 52

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces o...

  • Page 53

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 54

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 55

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Seat belt extender if a seat belt is not long enough to fi...

  • Page 56

    Seat belts and pregnant women seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong b...

  • Page 57

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Energy management feature this vehicle has a seat belt system with an energy manageme...

  • Page 58

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 59

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 60

    • supplemental side air bags • supplemental knee air bags • front and side impact sensors • seat belt pretensioners • seat belt buckle switch • seat track position sensors advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to the ...

  • Page 61

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 62

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 63

    Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away from an inflating air bag. When the orc detects a collision requiring the ad- vanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is generated ...

  • Page 64

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioner...

  • Page 65

    When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not se...

  • Page 66

    The sabic deploys downward, covering the side win- dows. An inflating sabic pushes the outside edge of the headliner out of the way and covers the window. The sabics inflate with enough force to injure occu- pants if they are not belted and seated properly, or if items are positioned in the area whe...

  • Page 67

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts. The occupant restraint controller (“orc”) determines whether the deployment of the side air bags in a particular impact event is appropriate, based on the severity and type of collision. The side impact sensors a...

  • Page 68

    Be properly restrained in a child restraint or booster seat that is appropriate for the size of the child. Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deploy- ment could ca...

  • Page 69

    • as the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the are...

  • Page 70

    • cut off battery power to the motor. • flash hazard lights as long as the battery has power or until the hazard light button is pressed. The hazard lights can be deactivated by pressing the hazard light button. • turn on the interior lights, which remain on as long as the battery has power. • unloc...

  • Page 71

    The mar position. After the self-check, the air bag warning light will turn off. If the orc detects a mal- function in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after initial s...

  • Page 72

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 73

    Assist in understanding how a vehicle’s systems per- formed. The edr is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle w...

  • Page 74

    Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash st...

  • Page 75

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 76

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 77

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 78

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 79

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 80

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 81

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 79.

  • Page 82

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 83

    Can the rear-facing child restraint touch the back of the front passenger seat? Yes the child seat may touch the back of the front passenger seat if the child restraint manufac- turer also allows contact. See your child re- straint owner’s manual for more information. Can the head restraints be remo...

  • Page 84

    Locating tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower ancho...

  • Page 85

    Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. To install a latch-compatible child restraint if the selected seating position has a switchable auto- matic locking retractor ...

  • Page 86

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused alr seat belt: when using the latch attaching system to install a child restraint, stow all alr se...

  • Page 87

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a l...

  • Page 88

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 89

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 90

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 91

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 92

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 93

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Safety checks you should make inside the vehicle seat belts inspect the seat belt system peri...

  • Page 94

    Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Floor mat safety information always use floor mats designed ...

  • Page 95

    Warning! (continued) • check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects can become trapped under the brake pedal an...

  • Page 97: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ inside day/night mirror . . . . . . . . . . . . . . . . .98 ▫ automatic dimming mirror — if equipped . . .98 ▫ power mirrors . . . . . . . . . . . . . . . . . . . . . . . .99 ▫...

  • Page 98

    ▫ parking lights. . . . . . . . . . . . . . . . . . . . . . . .110 ▫ daytime running lights. . . . . . . . . . . . . . . . .110 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ lane change assist . . . . . . . . . . . . . . . . . . . .111 ▫ follow me home/headlight delay . . . ....

  • Page 99

    ▫ to open . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ▫ to close . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ▫ pinch protect feature . . . . . . . . . . . . . . . . . . .128 ▫ wind buffeting . . . . . . . . . . . . . . . . . . . . . . .128 ▫ emergency operation. . . . ....

  • Page 100

    Mirrors inside day/night mirror the mirror can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night pos...

  • Page 101

    Note: this feature is disabled when the vehicle is moving in reverse. Caution! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Power mirrors the power mirror controls are locat...

  • Page 102

    The power mirror controls consist of a mirror select switch and a four-way mirror control switch. To adjust a mirror, push the mirror select switch to either the l (left) or r (right) to select the mirror you need to adjust. Using the mirror control switch, push on any of the four arrows for the dir...

  • Page 103

    Spotter mirror — if equipped some models are equipped with a driver’s side spotter mirror. The spotter mirror allows for a greater range of visibility on the driver’s side of the vehicle. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid d...

  • Page 104

    Sun visors the driver and passenger sun visors are located on the headliner, near the front windshield. The sun visor can be rotated downward or up against the door glass. Both sun visors are equipped with courtesy mirrors. Seats seats are a part of the occupant restraint system of the vehicle. Warn...

  • Page 105

    Forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearward on the s...

  • Page 106

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Seat height adjustment the driver’s seat height can be raised or lowered by using a le...

  • Page 107

    Ez entry feature the driver and front passenger seats have an ez entry feature for rear seat passengers. Pull forward on the release lever, located on the outboard side of the seatback, dump the seatback forward, then slide the seat forward to allow access in and out of the rear seat. Lift the seatb...

  • Page 108

    Fore/aft (memory) position on the tracks. This results in the seat back memory being set only – the track will then be locked forward of its last set fore/aft memory posi- tion. To then reset the fore/aft track memory feature (to reestablish memory function option 1), the seat has to be returned ful...

  • Page 109

    1. Pull the bottom of the red hood release lever, located on the left kick panel, rearward. 2. Rotate the safety catch under the front edge of the hood, near the center, and raise the hood. 3. Lift the hood prop rod that clips to the right side (left side when standing in front of the hood) of the e...

  • Page 110

    In hot climates, the prop rod may be hot. Pick up the prop rod at the foam on the end of the prop rod. Caution! To prevent possible damage, do not slam the hood to close it. Lower hood to approximately 12 in (30 cm) and drop the hood to close. Make sure hood is fully closed for both latches. Never d...

  • Page 111

    Lights multifunction lever the multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight beam selection, passing light and turn signals. Note: the headlights can only be turned on with the ignition in the on/run position. Headlights rota...

  • Page 112

    High beams with the low beams activated, push the multi- function lever towards the instrument panel to turn on the high beams. Pull the multifunction lever toward the steering wheel to turn off the high beams. Flash-to-pass you can signal another vehicle with your headlights by partially pulling th...

  • Page 113

    Note: the indicators will automatically turn off when the turn has been completed and the steering wheel is returned to a straight position. Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatical...

  • Page 114

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Interior lights the interior light switches are located in the overhead console. The interior lights can be set to three different positions (off/left position, center position, on/right positi...

  • Page 115

    • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is moved into the on/run position. Ambient light the vehicle is equipped with ambie...

  • Page 116

    Windshield wipers and washers the windshield wiper/washer lever is located on the right side of the steering column. Note: the windshield wipers/washers will only oper- ate with the ignition in the on/run position. Front windshield wiper operation there are five different modes of operation for the ...

  • Page 117

    Note: the intermittent function only has one detent but wiper delay will vary with changes in vehicle speed. As vehicle speed increases the delay time will decrease. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to th...

  • Page 118

    Caution! (continued) • always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Rear windshield wiper rotate the...

  • Page 119

    Hold the lever for more than a half second and the wipers will activate automatically for three cycles after the lever is released. Tilt steering column — if equipped this feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the left-side of the ste...

  • Page 120

    Warning! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Electronic speed control ...

  • Page 121

    To activate push the on/off button. The cruise indicator light in the instrument cluster will illuminate. To turn the system off, push the on/off button a second time. The cruise indicator light will turn off. The system should be turned off when not in use. Warning! Leaving the electronic speed con...

  • Page 122

    To vary the speed setting to increase speed when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more infor...

  • Page 123

    U.S. Speed (mph) • pushing the set (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph. • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed will ...

  • Page 124

    Rear park assist the rear park assist system provides audible indications of the distance between the rear fascia/bumper and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to the “park assist system usage pre- cautions” for the limitations of this system and recom- mendat...

  • Page 125

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 126

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 127

    Cm) from the sensors. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park ass...

  • Page 128

    Caution! (continued) • the vehicle must be driven slowly when using rear park assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using rear park assist. Warning! • drivers must be careful when backing up even wh...

  • Page 129

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key (continued) warning! (continued) fob in or near the vehicle, or in a location acces- sible to children. Occupants, particularly unat- tended children, can become entrapped by the power sunr...

  • Page 130

    To open push and hold the power sunroof switch rearward for approximately one second and the sunroof will stop at the vented position. Push the switch a second time and hold for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open”....

  • Page 131

    Emergency operation in case of electrical failure, the sunroof can be operated with the hex wrench that is located in the glove box. There is a plug located in the rear of the sunroof opening at the center of the vehicle. Removing the plug reveals a hex opening in the motor assembly of the sunroof. ...

  • Page 132

    Power is available when the ignition switch is in the on/run or start position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, do not hold the lighter in the heating position. Caution! • do not exceed the maximum power of 160 watts (13 amps) at 1...

  • Page 133

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 134

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 135

    Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. For rear passengers, there are cupholders located on the floor between the front driver and passenger seats. Front cupholders rear cupholders 3 understanding the features of your veh...

  • Page 136

    Storage glove compartment the glove compartment is located on the right side of the instrument panel. Pull outward on the glove compart- ment latch to open the glove compartment. Push the glove compartment door upward to close it. Cargo area features the rear seatbacks have a fold down feature to al...

  • Page 137

    Rear seat release buttons folded rear seats 3 understanding the features of your vehicle 135.

  • Page 138

    Rear window features rear window defroster the rear window defroster button is located in the center of the instrument panel, below the radio. Push this button to turn on the rear window defroster. An indicator in the instrument panel cluster will illuminate when the rear window defroster is on. The...

  • Page 139: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .139 䡵 instrument cluster . . . . . . . . . . . . . . . . .141 䡵 warning and indicator lights . . . . . . .142 ▫ red telltale indicator lights . . . . . . . . . . . . . .143 ▫ yellow telltale indicator lights ...

  • Page 140

    ▫ customer programmable features — uconnect 5.0 settings . . . . . . . . . . . . . . . . . . . . . . . . .172 䡵 uconnect 5.0 voice recognition quick tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 ▫ introducing uconnect. . . . . . . . . . . . . . . . . . .180 ▫ get started . ...

  • Page 141

    Instrument panel features 4 understanding your instrument panel 139.

  • Page 142

    1 — side vent 6 — storage compartment 11 — power window controls 2 — multifunction lever – light control (behind steering wheel) 7 — passenger air bag 12 — heated seat controls/front fog light control 3 — instrument cluster and elec- tronic vehicle information center 8 — rear defrost button 13 — esc...

  • Page 143

    Instrument cluster instrument cluster 4 understanding your instrument panel 141.

  • Page 144

    1. Battery charge gauge • this gauge indicates the charge level of the battery. 2. Speedometer • indicates vehicle speed. 3. Electronic vehicle information center (evic) • when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “e...

  • Page 145

    Red telltale indicator lights seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is ...

  • Page 146

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspe...

  • Page 147

    Brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid le...

  • Page 148

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 149

    Electric power steering fail warning — if equipped red telltale light what it means electric power steering fail warning this light is used to manage the electrical warning of the eps (power steering system). Re- fer to “power steering” in “starting and operating” for further information. Plugged in...

  • Page 150

    Door open warning light red telltale light what it means door open warning light this indicator will illuminate when a door is ajar/open and not fully closed. . • driver’s door open • passenger door open • driver and passenger door open 148 understanding your instrument panel.

  • Page 151

    Service propulsion system warning light red telltale light what it means service propulsion system warning light the service propulsion system warning light will illuminate if there is a malfunction de- tected with the propulsion system. If the light comes on or remains on while driving see your aut...

  • Page 152

    Liftgate open warning light red telltale light what it means liftgate open warning light this indicator will turn when the liftgate is open. Yellow telltale indicator lights ev system malfunction indicator light yellow telltale light what it means ev system malfunction indicator light this indicator...

  • Page 153

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the avv/start position. If the “esc indicator...

  • Page 154

    Electronic stability control (esc) off indicator light — if equipped yellow telltale light what it means electronic stability control (esc) off indicator light this light indicates the electronic stability control (esc) is off. 152 understanding your instrument panel.

  • Page 155

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 156

    On the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of...

  • Page 157

    When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the tpms from functi...

  • Page 158

    Vehicle security indicator light yellow telltale light what it means vehicle security indicator light this indicator will illuminate when the vehicle theft alarm system has detected an attempt was made to break into the vehicle. Regenerative brake system (rbs) indicator light yellow telltale light w...

  • Page 159

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light this light monitors the anti-lock brake system (abs). The light will turn on when the igni- tion switch is placed in the on/run position and may stay on for as long as four seconds. If the...

  • Page 160

    Rear defrost light yellow telltale light what it means rear defrost light this indicator will illuminate when the rear window defroster is on. The rear window de- froster automatically turns off after 20 minutes.. Caution! Failure to follow these cautions can cause damage to the heating elements: • ...

  • Page 161

    Icy road condition indicator light yellow telltale light what it means icy road condition indicator light this light will illuminate during an icy road condition. Exterior bulb failure indicator light yellow telltale light what it means exterior bulb failure indicator light this light will illuminat...

  • Page 162

    Green telltale indicator lights park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. Front fog indicator light — if equipped green telltale light what it means front fog...

  • Page 163

    Turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster arrow will flash independently for the left or right turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function leve...

  • Page 164

    Plugged in indicator light green telltale light what it means plugged in indicator light this green indicator will illuminate when the vehicle is plugged in. White telltale indicator light electronic speed control on indicator light white telltale light what it means electronic speed control on indi...

  • Page 165

    Blue telltale indicator light high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch...

  • Page 166

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • outside temperature di...

  • Page 167

    Push and release the menu esc button briefly to access the menu and/or go to next screen or to confirm the required menu option. Push and hold the menu esc button (approximately one second) to return to the main screen. Push and release the + button to scroll upward through the displayed menu and th...

  • Page 168

    The setup menu can be activated by pushing the menu esc button. Single pushes on the + or – buttons will scroll through the setup menu options. The menu in- cludes the following functions: • battery % display • button volume • stored warnings • tutorial • connectivity id • restore factory settings •...

  • Page 169

    5. Briefly push and release the menu esc button to store the new setting and go back to the previously selected submenu option. 6. Push and hold the menu esc button to return to the main menu (short hold) or the main screen (longer hold). Trip computer the trip computer is located in the instrument ...

  • Page 170

    The user-selectable options are: • motor power (kilowatts) • trip a • trip b • tire pressure new trip to reset: • push and hold the trip button manually. • when the “trip distance” reaches 9999.9 miles/ kilometers or when the “elapsed time” reaches 29.59 (29 hours and 59 minutes) the system will res...

  • Page 171

    Values displayed range this indicates the distance which may be travelled with the remaining battery charge, assuming that driving conditions will not change. The message “----” will appear when the system is initializing. Note: the range depends on several factors: driving style, type of route (fre...

  • Page 172

    Ipod/usb/media player control — if equipped this feature allows an ipod or external usb device to be plugged into the usb or aux port, located in the center console. Usb/aux port 1 — auxiliary cable jack 2 — usb connector 170 understanding your instrument panel.

  • Page 173

    Uconnect settings the uconnect system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many features can vary by vehicle. Uconnect 5.0 buttons on the tou...

  • Page 174

    Buttons on the faceplate buttons on the faceplate are located below, and beside the uconnect system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90)...

  • Page 175

    Press the “x” button on the touchscreen to close out of the settings screen. Pressing the up or down arrow buttons on the right side of the screen will allow you to toggle up or down through the available settings. Note: all settings should be changed with the ignition in the “ avv/acc ” position. C...

  • Page 176

    Brightness with the “+” and “–” setting buttons on the touchscreen or by selecting any point on the scale be- tween the “+” and “–” buttons on the touchscreen. • language when in this display, you may select one of multiple languages (english/español/français) for all display no- menclature, includi...

  • Page 177

    Voice after pressing the “voice” button on the touchscreen the following settings will be available: • voice response length when in this display, you may change the voice re- sponse length settings. To change the voice response length, press the “voice response length” button on the touchscreen and...

  • Page 178

    • set date when in this display, you may set the date manually. Press the “set date” button on the touchscreen then press the corresponding arrows above and below the current date to adjust. • sync time — if equipped when in this display, you may sync the time with gps. Press the “sync time” button ...

  • Page 179

    • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 12 mph (20 km/h). To make your selection, press the “auto door locks” button on the touchscreen and select from “on” or “off.” • remote door unlock/door unlock when “driver” is se...

  • Page 180

    Setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the touchscreen. Note: bass/mid/treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. • balance when in this display ...

  • Page 181

    During that current song. Tune start works in the back- ground, so you will not even realize it’s on, except that you will miss the experience of joining your favorite song with only a few seconds left to play. To make your selection, press the “tune start” button on the touch- screen, select “on” o...

  • Page 182

    To restore the settings to their default setting, press the restore settings button. A pop-up will appear asking ⬙are you sure you want to reset your settings to default?” select “yes” to restore, or “no” to exit. Once the settings are restored, a pop up appears stating ⬙settings reset to default. ⬙...

  • Page 183

    Get started 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing in- structions. 2. Reduce background noise. Wind and passenger con- versations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facin...

  • Page 184

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice ...

  • Page 185

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say ѧ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 uconn...

  • Page 186

    Tip: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say “help.” the system will provide you with a list of commands. Media uconnect offers connections via usb, bluetooth and auxiliary ports (if equipped). Voice operation is only available for...

  • Page 187

    Tip: press the “browse” button on the touchscreen to see all of the music on your ipod or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Voice text reply uconnect will announce incoming text messages. Push the phone button and say li...

  • Page 188

    Pre-defined voice text reply responses okay. Where are you? I will be ber> minutes late. Call me. Are you there yet? I’ll call you later. I need direc- tions. See you in of minutes. I’m on my way. Can’t talk right now. I’m lost. Thanks. Tip: your mobile phone must have the full implementa- tion of t...

  • Page 189

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Uconnect system suppo...

  • Page 190

    The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing the top of the rocker switch will increase the volume, and pushing the bottom of the rocker switch will decrease the volume. Pushing the center button will mak...

  • Page 191

    Telematics modem your vehicle is equipped with a 3g cdma cellular modem to connect the vehicle with your device to provide the following features: • range and state of charge information • configure scheduled charging profile • average and total energy used • charge station location and availability...

  • Page 192

    Automatic temperature control (atc) • the automatic temperature control (atc) allows the occupant to select a comfort settings. • the system provides set-and-forget operation for op- timum comfort and convenience. • the system can be controlled manually, if desired. The atc system automatically main...

  • Page 193

    2. A/c button push and release to change the current air conditioning (a/c) setting. Performing this function will cause the atc to switch into manual mode. 3. Temperature control up button provides temperature up control. Push the button for warmer temperature settings. 4. Blower control up/down bu...

  • Page 194

    And side window demist outlets. When the defrost but- ton is selected, the blower level will increase. Use defrost mode with maximum temperature settings for best wind- shield and side window defrosting and defogging. Per- forming this function will cause the atc to switch into manual mode. If the f...

  • Page 195

    11. Climate control on/off button push and release to turn the climate control on or off. 12. Recirculation control button push and release to change the current setting. The indicator illuminates when on. Note: when in defrost mode, the recirculation button will flash if pushed. This indicates that...

  • Page 196

    This button is selected. Push the button a second time to turn off the recirculation mode led and allow outside air into the vehicle. Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (indicator light shall blink) if c...

  • Page 197

    Feature. Refer to the “electronic vehicle information center (evic) — customer-programmable features” in this section of the manual. Manual operation the system allows for manual selection of blower speed, air distribution mode, a/c status and recirculation con- trol. The blower fan speed can be set...

  • Page 198

    Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Note: automatic temperature controls...

  • Page 199

    Operating tips chart 4 understanding your instrument panel 197.

  • Page 201: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .202 ▫ single-speed transmission . . . . . . . . . . . . . . .202 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .202 䡵 single–speed transmission . . . . . . . . . . .203 ▫ key ignition park interlock. ...

  • Page 202

    ▫ electronic stability control (esc) . . . . . . . . . .219 ▫ esc activation/malfunction indicator light and esc off indicator light . . . . . . . . . . . .221 ▫ regenerative braking system (rbs) . . . . . . . . .222 䡵 tire safety information . . . . . . . . . . . . .223 ▫ tire markings . . . . . . ...

  • Page 203

    ▫ tire pressure monitoring low pressure warnings . . . . . . . . . . . . . . . . . . . . . . . . . . .252 ▫ tpms warning . . . . . . . . . . . . . . . . . . . . . . .253 ▫ general information . . . . . . . . . . . . . . . . . . .255 䡵 trailer towing . . . . . . . . . . . . . . . . . . . . .255 䡵 rec...

  • Page 204

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 205

    Note: • if the key is held in the start position for more than 10 seconds “ready” mode will not be achieved. Return the key to off position, and then back to the start position and hold for less than 10 seconds to achieve “ready”. • if the “ready” indicator fails to illuminate after you have followe...

  • Page 206

    The push-buttons are located on the lower instrument panel. Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • place the transmission into park only after the vehicle has come to a complete stop. • place the transmission into or out of reverse only after...

  • Page 207

    Warning! • only place the transmission into gear when your foot is firmly pressing the brake pedal. • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the vehicle is in “ready” mode. Before exiting a vehicle, alwa...

  • Page 208

    Gear ranges push the desired push button to shift into gear. Note: • the brake pedal must be depressed to select a trans- mission gear. • after selecting any gear, wait a moment to allow the selected gear to engage before accelerating. Park (p) the park selection supplements the parking brake by loc...

  • Page 209

    Warning! (continued) • it is dangerous to shift out of park or neutral if your foot is not firmly pressing the brake pedal. The vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift the transmis- sion into gear when you...

  • Page 210

    Reverse (r) this gear is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) the vehicle may be started in this gear. Apply the parking brake and place the transmission into park if you must leave the vehicle. Warning! Do not coast in n...

  • Page 211

    Auto park is enabled under the following conditions: • key on (12 volt on and high voltage off) or ready mode (12 volt on and high voltage on). • vehicle speed is below 2 mph (3 km/h). Note: • auto park is enabled (only once) at the beginning of each key cycle and is re-enabled each time the vehicle...

  • Page 212

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 213

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 214

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., transmission, coolant, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through standing water....

  • Page 215

    Prevents it from providing assist, you will still have the ability to steer the vehicle manually. Warning! Continued operation with reduced or no power steer- ing assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. If the steering icon is flashing,...

  • Page 216

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To release the parking brake, pull the lever up slightly, push the center button...

  • Page 217

    Should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injur...

  • Page 218

    Brake system in the event regenerative braking or power assist is lost for any reason the brakes will still function. The effort required to brake the vehicle will be significantly more than that required with the power system operating. If either the front or rear hydraulic system loses normal capa...

  • Page 219

    The ignition off and on again may reset the abs if the fault detected was only momentary. Warning! • pumping the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow dow...

  • Page 220

    System detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The bas complements the anti-lock brake system (abs). Applying the brakes very quickly results in the best bas ...

  • Page 221

    The other, the system will apply the brake of the spinning wheel. This will allow more torque to be applied to the wheel that is not spinning. This feature remains active even if tcs and esc are in the partial off mode. Refer to “electronic stability control (esc)” in this section for further inform...

  • Page 222

    Warning! (continued) hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inap- propriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent acci- dents. The capabilities of an esc equipped vehicle must never be exploite...

  • Page 223

    Partial off this mode is entered by momentarily pushing the esc off switch. This mode is intended to be used if the vehicle is in deep snow, sand or gravel conditions and more wheel spin than esc would normally allow is required to gain traction. To turn esc on again, momentarily pushing the switch ...

  • Page 224

    On continuously with the vehicle operating running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as p...

  • Page 225

    Which propel the vehicle forward can operate as genera- tors when braking. The rbs recharges the high voltage battery under certain braking conditions by recapturing energy that would otherwise be lost while braking. The electric power that is generated goes back into the high voltage battery for la...

  • Page 226

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 227

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 228

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 229

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 230

    Example: dot ma l9 abcd 0301 03 = number representing the week in which the tire was manufactured (two digits) – 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only require...

  • Page 231

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the ve- hicle has not been driven for at least three ho...

  • Page 232

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 230 starting an...

  • Page 233

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 234

    Occupants and cargo should never exceed xxx lbs or xxx kg” on the tire and loading information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for determining correct load limit 1. Locate the sta...

  • Page 235

    5 starting and operating 233.

  • Page 236

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 237

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 238

    At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Cau...

  • Page 239

    Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too low. Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits ...

  • Page 240

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 241

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 242

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 243

    Equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spa...

  • Page 244

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 245

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 246

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (1.6 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information....

  • Page 247

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 248

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 249

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer • install on front tires • due to limited ...

  • Page 250

    Caution! (continued) • do not drive for prolonged period on dry pave- ment. • observe the tire chain manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the lower suggested operating speed of the chain manufacturer if dif- ferent from the sp...

  • Page 251

    Premium tire pressure monitor system the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1psi (7 kpa) for every 12°f (6.5°c). This means that when the outsi...

  • Page 252

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring telltale light) illuminates, you must inc...

  • Page 253

    Caution! (continued) sensor damage. Using aftermarket tire sealants may cause the tire pressure monitoring system (tpms) sensor to become inoperable. After using an after- market tire sealant it is recommended that you take your vehicle to an authorized dealership to have your sensor function checke...

  • Page 254

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Premium tpm system the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to...

  • Page 255

    Should this occur, you should stop as soon as possible and inflate the tires with low pressure to the vehicle’s recom- mended cold placard pressure value. Once the system receives the updated tire pressures, the system will auto- matically update and the “tire pressure monitoring tell- tale light” w...

  • Page 256

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the “service tpm sys- tem” message will no longer display. A system fault can occur due ...

  • Page 257

    A chime will sound. In addition, the highlighted graphic in the evic will still display a low pressure text message and a pressure value in a different color. • after driving the vehicle for up to 20 minutes above 15 mph (24 km/h), the “tire pressure monitoring telltale light” will flash on and off ...

  • Page 258

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground single-speed transmission flat tow none not allowed dolly tow front ok rear not allowed on trailer all ok note: • when recreationally towing your vehicle, always fol- low ap...

  • Page 259

    Extending your driving range per charge the drive system and cabin temperature management features use the most energy from the high voltage battery. Reducing energy draw from these features are the easiest and most effective way to extend driving range. The 500e uses high voltage components to heat...

  • Page 260

    Behavior gauge. The driver behavior gauge is located on the right side of the instrument cluster and contains three driving ranges: • power the needle will move into the power range when under acceleration. • eco the needle will move into the eco range when you are maximizing the driving range of th...

  • Page 261

    Range projection this area of the cluster is used to display the projected range considering current battery charge and previous energy use. The two arrows to the left of the mileage are used to forecast the effect of recent driving. • when both arrows are grey, expect the range to drop approximatel...

  • Page 263: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .262 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .262 ▫ torque specifications . . . . . . . . . . . . . . . . . . .262 䡵 tire service kit — if equipped . . . . . . . . .264 ▫ tire se...

  • Page 264

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Push the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 265

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are proper...

  • Page 266

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tire service kit — if equipped small punctures up to 1/4 inch (6 mm) in the tire tread can be sealed wit...

  • Page 267

    Tire service kit components and operation using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black ai...

  • Page 268

    Using the deflation button push the deflation button (2) to reduce the air pressure in the tire if it becomes over-inflated. Tire service kit usage precautions • replace the tire service kit sealant bottle (1) and sealant hose (6) prior to the expiration date (printed at the lower right hand corner ...

  • Page 269

    From the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tire service kit. • you can use the tire service kit air pump to inflate...

  • Page 270

    Warning! (continued) • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warn- ings can result ...

  • Page 271

    On the ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceeding. 3. Place the transmission in park (auto transmission) or in gear (man...

  • Page 272

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Push the power button (4) to turn off the tire service kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is ...

  • Page 273

    Latch pillar (recommended pressure). Check the tire pressure by looking at the pressure gauge (3). If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tir...

  • Page 274

    (d) drive vehicle: immediately after injecting sealant and inflating the tire, drive the vehicle 5 miles (8 km) or 10 minutes to ensure distribution of the tire service kit sealant within the tire. Do not exceed 55 mph (90 km/h). Warning! Tire service kit is not a permanent flat tire repair. Have th...

  • Page 275

    If the tire pressure is 19 psi (1.3 bar) or higher: 1. Push the power button (4) to turn on tire service kit and inflate the tire to the pressure indicated on the tire and loading information label on the driver-side door opening. Note: if the tire becomes over-inflated, push the defla- tion button ...

  • Page 276

    4. Clean any remaining sealant from the tire service kit housing. 5. Position the new sealant bottle (1) in the housing so that the sealant hose (6) aligns with the hose slot in the front of the housing. Push the bottle into the housing. An audible click will be heard indicating the bottle is locked...

  • Page 277

    Preparations for jump-start the battery in your vehicle is located in the underhood compartment under the beauty cover. To access the battery pull upward on the cover. Battery posts 1 — positive (+) post (covered with protective cap) 2 — negative (-) post 6 what to do in emergencies 275.

  • Page 278

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 279

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end...

  • Page 280

    6. Once the vehicle is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) jumper cable from the engine ground (-) of the vehicle with the discharged battery. 2. Disconnect the negative end (-) of the jumper cable from the negativ...

  • Page 281

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • spinning the wheels too fast may lead to transmis- sion overheating and failure. It can also damage the tires. Do not spin the wh...

  • Page 282

    In order to move the vehicle in cases where the transmis- sion will not shift out of park (such as a dead battery), a manual park release is available. If a dead 12 volt battery is the cause of the condition refer to “jump start procedure — 12 volt battery” before performing the manual park release....

  • Page 283

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheels off the ground single-speed transmission flat tow none not allowed wheel lift rear not allowed front ok flatbed all ok this vehicle must be towed with ...

  • Page 285: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 underhood compartment . . . . . . . . . . .285 䡵 replacement parts . . . . . . . . . . . . . . . . . .286 䡵 dealer service . . . . . . . . . . . . . . . . . . . . . .286 䡵 maintenance procedures . . . . . . . . . . .286 ▫ power electronics and battery thermal mana...

  • Page 286

    ▫ wiper blades . . . . . . . . . . . . . . . . . . . . . . . .297 ▫ adding washer fluid . . . . . . . . . . . . . . . . . .299 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .300 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .302 䡵 ...

  • Page 287

    Underhood compartment 1 — battery thermal coolant reservoir 4 — fuses 2 — power electronics coolant reservoir 5 — 12v battery 3 — brake fluid reservoir 7 maintaining your vehicle 285.

  • Page 288

    Replacement parts use of genuine parts for normal/scheduled maintenance and repairs is highly recommended to ensure the de- signed performance. Damage or failures caused by the use of parts which are not quality-equivalent to genuine parts for maintenance and repairs will not be covered by the manuf...

  • Page 289

    Warning! (continued) voltage are both extremely dangerous and can cause severe burns, electric shock, serious injury or even death. In order to avoid personal injuries: • do not touch the high voltage cables (orange colored) and/or the connec- tors. • follow all caution and warning labels attached t...

  • Page 290

    Caution! (continued) damage is not covered by the new vehicle limited warranty. If a flush is needed because of compo- nent malfunction, use only the specified fluid for the flushing procedure. Power electronics and battery thermal management systems the power electronics and battery thermal managem...

  • Page 291

    When additional coolant (antifreeze) is needed to main- tain the proper level, it should be added to the coolant bottles. Do not overfill. Check the power electronics and battery thermal man- agement systems coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where...

  • Page 292

    Warning! You or others can be badly burned by hot coolant (antifreeze) or steam from your radiator. If you see or (continued) warning! (continued) hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when...

  • Page 293

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add coolant (antifreeze) when the cooling system is overheated. Do not loosen or remove the cap to cool an overheated cooling system. Heat causes pressure to build up in the cooling syste...

  • Page 294

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based coolant (antifreeze). Use of propylene glycol-based coolant (antifreeze) is not recommended. Adding coolant your vehicle has been built with cooling systems that allow extended maintenance intervals. This c...

  • Page 295

    Note: mixing coolant (antifreeze) types will decrease the life of the power electronics and battery thermal management systems coolant (antifreeze) and will re- quire more frequent coolant (antifreeze) changes. Power electronics and battery thermal management systems — drain, flush and refill refer ...

  • Page 296

    Points to remember if an examination of your underhood compartment shows no evidence of cooler or hose leaks, the vehicle may be safely driven. • do not overfill the coolant recovery bottles. • check coolant (antifreeze) freeze point in the coolant recovery bottles. If coolant (antifreeze) needs to ...

  • Page 297

    Warning! (continued) splashes in eyes or on skin, flush the area imme- diately with large amounts of water. Refer to “jump-starting procedures” in “what to do in emergencies” for further information. • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a b...

  • Page 298

    Include cleaning of the condenser fins and air condition- ing performance tests. Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Warning! • use only re...

  • Page 299

    Lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mecha- nism and safety catch should be cleaned and lubricated. The external lock cyl...

  • Page 300

    Rear wiper blade removal/installation 1. Lift the pivot cap on the rear wiper arm upward, this will allow the rear wiper blade to be raised off of the liftgate glass. Note: the rear wiper arm cannot be raised fully up- ward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to r...

  • Page 301

    4. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly press the wiper blade until it snaps into place. 5. Lower the wiper blade and snap the pivot cap into place. Adding washer fluid the windshield washer fluid reservoir is located in the underhood ...

  • Page 302

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 303

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 304

    Caution! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Appearance care and protection from corrosion protection of body and paint from co...

  • Page 305

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar super kleen bug and tar remover t...

  • Page 306

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 307

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar wheel...

  • Page 308

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar total clean. C...

  • Page 309

    Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses ...

  • Page 310

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 311

    Warning! (continued) damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assem- blies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn webbing, etc.). Fuses warning! • when replacing a blown fuse, always use an appro-...

  • Page 312

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Cavity vehicle fuse number mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 5 amp tan front and rear ceil- ing lights trunk and door courtesy ...

  • Page 313

    Cavity vehicle fuse number mini fuse description 6 f43 20 amp yellow bi-directional washer 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp brown left low beam 9 f50 7.5 amp brown airbag 10 f51 5 amp tan climate control sys- tem, stop light, exte- rior mirrors, sunroof switch cavity vehicle ...

  • Page 314

    1 — heated mirror fuse 2 — access panel cavity mini fuse description f90 5 amp tan heated mirrors power distribution center #1 the power distribution center #1 is located on the right side of the underhood compartment. To access the fuses, remove locking screw and slide cover off. F90 fuse location ...

  • Page 315

    The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Cavity maxi fuse mini fuse description f01 60 amp blue – body control module (bcm) f02 20 amp yellow – audio amplifier f03 20 amp yellow – ignition switch f04 40 amp orange – brake system mo...

  • Page 316

    Cavity maxi fuse mini fuse description f16 – 10 amp red humidity sensor vpam ac compressor f18 – 5 amp tan electronic vehicle control unit (evcu) f19 – 10 amp red hvac f20 – 15 amp blue heated seats – if equipped f21 – 20 amp yellow radio f23 – 25 amp clear anti-lock brake valves cavity maxi fuse mi...

  • Page 317

    Power distribution center (pdc) #2 the power distribution center #2 is located next to the battery in the underhood compartment. To access the fuses, pull the release tabs and remove the cover. Cavity maxi fuse mini fuse description fpt9 – 15 amp blue battery pack con- trol module (bpcm) power inver...

  • Page 318

    Cavity cartridge fuse description fpt3 25 amp white battery coolant pump fpt5 20 amp lt. Blue inverter coolant pump fpt6 40 amp green supply for fuses f9, f13, f16, f17 and f20 vehicle storage the preferred way of storing your vehicle for a long period of time is to leave it attached to a level 1 or...

  • Page 319

    Exterior bulbs bulb number front low and high beam headlamp hir2ll front parking/daytime running lamps w21/5w front fog lamps h11ll front side marker lamps w3w front turn signal lamps wy21w side direction lamps wy5w rear turn signal lamps py21w rear side marker lamps w3w rear tail and stop lamps p21...

  • Page 320

    Headlamps low beam and high beam 1. Remove the plastic cap from the back of the headlamp housing. 2. Rotate the bulb counter-clockwise. 3. Remove the bulb and replace as needed. 4. Install the bulb and rotate clockwise to lock in place. 5. Reinstall the plastic cap. Front turn signal, parking and da...

  • Page 321

    6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. 7. Reinstall the plastic cap. Front fog lamps to replace the front fog lights, see your authorized dealer. Front/rear side marker lamps 1. Remove portion of the wheel liner to allow hand access to side m...

  • Page 322

    3. Remove four screws and separate the backplate from the lamp housing. 4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 5. Remove the backup lamp bulb by pulling straight out. 6. Replace lamps as required and reinstall lamp. Center high mounted ...

  • Page 323

    Fluids, lubes, and genuine parts component fluid, lubricant, or genuine part coolant mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms.90032. Brake master cylinder mopar dot 3, sae j1703 should b...

  • Page 324

    Caution! • mixing of coolant (antifreeze) other than specified organic additive technology (oat) coolant (anti- freeze), may result in cooling system damage and may decrease corrosion protection. Organic addi- tive technology (oat) coolant is different and should not be mixed with hybrid organic add...

  • Page 325: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .324 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .324 8.

  • Page 326

    Maintenance schedule once a month or before a trip: • check windshield washer fluid level • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoirs and brake master cylinder • check function of all interior and exterior lights require...

  • Page 327

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 328

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 329

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 331: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .331 ▫ prepare for the appointment. . . . . . . . . . . . .331 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .331 ▫ be reasonable with requests ....

  • Page 332

    ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .337 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .337 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .338 330 if you need consumer assistance.

  • Page 333

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 334

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 335

    Puerto rico and u.S. Virgin islands customer service chrysler international services llc p.O. Box 191857 san juan 00919-1857 tel.: (787) 782-5757 fax: (787) 782-3345 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer h...

  • Page 336

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 337

    Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying the manufacturer. I...

  • Page 338

    Service manuals these comprehensive service manuals provide the infor- mation that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing fca usa llc vehicles. A complete working knowledge of the vehicle, system, and/or comp...

  • Page 339

    Department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle....

  • Page 340

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 341: Index

    Index 10

  • Page 342

    Adding washer fluid . . . . . . . . . . . . . . . . . . . . . .299 air bag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57, 58 advance front air bag . . . . . . . . . . . . . . . . .58, 59 air bag operation . . . . . . . . . . . . . . . . . . . . . . .60 air bag warning light . . . . ...

  • Page 343

    Body mechanism lubrication . . . . . . . . . . . . . . . . .296 b-pillar location . . . . . . . . . . . . . . . . . . . . . . . . . .230 brake assist system . . . . . . . . . . . . . . . . . . . . . . .217 brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321 brake, parking . . . ...

  • Page 344

    Clutch fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 compact spare tire . . . . . . . . . . . . . . . . . . . . . . . .241 connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 universal consumer interface (uci) . . . . . . . . . .170 contract, servi...

  • Page 345

    Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . .285 starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 enhanced accident response feature . . . . . . . . . . . .67 event data recorder . . . . . . . . . . . . . . . . . . . . . . . .70 exterior lights . . . ....

  • Page 346

    Instrument panel cover . . . . . . . . . . . . . . . . . . . . .307 instrument panel lens cleaning . . . . . . . . . . . . . . .308 interior appearance care . . . . . . . . . . . . . . . . . . . .305 interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . .112 key fob disarm the alarm . ...

  • Page 347

    Locks automatic door . . . . . . . . . . . . . . . . . . . . . . . . .41 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 power door . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .296 lug nuts . . ....

  • Page 348

    Pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .237 radio frequency general information . . . . . . . . . . . . . . . . . . .34, 39 radio operation . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 349

    Seat belt pretensioner . . . . . . . . . . . . . . . . . . . . .54 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .46 seat belt system . . . . . . . . . . . . . . . . . . . . . . . . .44 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .308 seat belt reminder . . . . ....

  • Page 350

    Tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .117 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 steering wheel audio controls . . . . . . . . . . . . . . .187 steering wheel mounted sound system controls . . .187 storage, vehicle. . . . . . . . . . . . . ....

  • Page 351

    Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .256 towing vehicle behind a motorhome . . . . . . . . . . .256 traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210 traction control . . . . . . . . . . . . . . . . . . . . . . . . . .218 trailer towing . . . . ...

  • Page 352

    Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 windshield defroster . . . . . . . . . . . . . . . . . . . . . . .92 windshield washers . . . . . . . . . . . . . . . . . . . .114, 116 windshield wiper b...

  • Page 353

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 354

    First edition printed in u.S.A. ©2015 fca us llc. All rights reserved. Fiat is a registered trademark of fiat group marketing & corporate communication s.P.A., used under license by fca us llc. 16bev24-126-aa 16bev24-126-ab second edition.