1. DL manuals
  2. Fiat
  3. Automobile
  4. 500L 2014
  5. Owner's Manual

Fiat 500L 2014 Owner's Manual

Other manuals for 500L 2014: Owner's Manual, User Manual

Summary of 500L 2014

  • Page 1

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 fia t 500l 14bf-126-ac third edition printed in u.S.A. Fiat 500l.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 䡵 vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition switch . . . . . . . . . . . . . . . . . . . . . . . .12 䡵 sentry key® . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ replacement keys . . . . . . . . . . . . . . . . . . . . ....

  • Page 12

    䡵 door locks . . . . . . . . . . . . . . . . . . . . . . . . .20 ▫ doors lock with one or more doors open . . .23 ▫ auto — relocking (only for rear doors) . . . . .23 ▫ child-protection door lock system — rear doors . . . . . . . . . . . . . . . . . . . . . . . . . .23 䡵 power windows . . . . . . . ...

  • Page 13

    䡵 engine break-in recommendations . . . .79 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ transporting passengers. . . . . . . . . . . . . . . . . .80 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ safety checks you should make inside the vehicle . . . ...

  • Page 14

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 15

    The ignition switch is fitted with a safety system that requires the ignition key to be turned back to stop if the engine does not start, before the starting operation can be repeated. Sentry key® the sentry key® immobilizer system prevents unau- thorized vehicle operation by disabling the engine. T...

  • Page 16

    Caution! • always remove the sentry key® from the vehicle and lock all doors when leaving the vehicle unat- tended. • the sentry key® immobilizer system is not com- patible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of secur...

  • Page 17

    Vehicle security alarm — if equipped the vehicle security alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If something triggers...

  • Page 18

    If the vehicle security alarm sounds the horn a second time even when all doors, hood and liftgate are correctly closed, a fault has occurred in the operation of the system. Contact your authorized studio. To disarm the system press unlock on the rke transmitter, or insert the key into the ignition ...

  • Page 19

    Activating the safe lock device the safe lock device is enabled on all the doors by quickly double-pressing the lock button on the rke transmitter. The direction indicators flash three times and the led above the button flashes to indicate that the safe lock device has been activated. If one or more...

  • Page 20

    Remote keyless entry (rke) this system allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmit- ter. The rke transmitter does not need to be pointed at the vehicle to activate the system. Note: the line...

  • Page 21

    Replacing the battery in the key with remote control to replace the battery, proceed as follows: • press button a fig. 16 and open the metal insert b; • turn the screw c to unlock using a fine bit screw- driver; • take out the battery case d and replace the battery e making sure that polarities are ...

  • Page 22

    Request for additional remote controls the system can recognize up to 8 remote controls. Should a new remote control be necessary, go to an authorized studio, taking an id document and the car ownership documents. General information this device complies with part 15 of fcc rules and with rs-210 of ...

  • Page 23

    • led off: doors unlocked. Pressing the central lock/unlock button once will lock all doors. The led will switch on once the doors are locked. Once the doors have been locked with the rke transmit- ter, it will no longer be possible to unlock them by pressing central lock/unlock button. Note: with c...

  • Page 24

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before ex...

  • Page 25

    Doors lock with one or more doors open it is possible locking the vehicle through the rke, internal button or external key pawl, also if one or more doors are open. At lock command request, led is switched on. At closing of the last door, the vehicle maintains the central locking status if key is no...

  • Page 26

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, unlock the doors usin...

  • Page 27

    Note: the power window switches will remain active for up to three minutes after the ignition switch is cycled to the off position. Opening either front door will cancel this feature. Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave...

  • Page 28

    Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- closu...

  • Page 29

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 30

    Liftgate emergency release as a security measure, a liftgate emergency release is built into the liftgate latching mechanism. To access the liftgate emergency release proceed as follows: 1. Remove the rear headrests and fold down the seats completely 2. Take the screwdriver from the tool box supplie...

  • Page 31

    Occupant restraints some of the most important safety features in your vehicle are the restraint systems: • three-point lap and shoulder belts for all seating positions • advanced front air bags for driver and front passen- ger • supplemental driver side knee air bag • supplemental side air bag infl...

  • Page 32

    Please pay close attention to the information in this section. It tells you how to use your restraint system properly, to keep you and your passengers as safe as possible. If you will be carrying children too small for adult-sized seat belts, the seat belts or the lower anchors and tether for childr...

  • Page 33

    You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should always wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air...

  • Page 34

    Warning! (continued) • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up...

  • Page 35

    3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 2 things to know before starting your vehicle 33.

  • Page 36

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 37

    4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. War...

  • Page 38

    6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed posi- tion. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Warning! A frayed or torn belt could rip apart in a collision and leave you with no protec...

  • Page 39

    Additional information, refer to “installing child re- straints using the vehicle seat belt” under the “child restraints” section. The chart below defines the type of feature for each seating position. Driver center passenger first row n/a n/a alr second row alr alr alr • n/a — not applicable • alr ...

  • Page 40

    2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode unbuckle the combin...

  • Page 41

    Seat belt pretensioners the seat belts for both front seating positions are equipped with dual pretensioning devices that are de- signed to remove slack from the seat belt in the event of a collision. The dual pretensioning devices are located on the lower b-pillars and in the kick plate area. These...

  • Page 42

    Unbuckled while traveling at speeds greater than 6 mph (10 km/h), beltalert® will provide both audio and visual notification. The front passenger seat beltalert® is not active when the front passenger seat is unoccupied. Beltalert® may be triggered when an animal or heavy object is on the front pass...

  • Page 43

    Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Supplemental restraint system (srs) — air b...

  • Page 44

    This vehicle is equipped with supplemental seat- mounted side air bags (sab). The sab are marked with an air bag label sewn into the outboard side of the front seats. Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Advanced driver air bag...

  • Page 45

    • after any collision, the vehicle should be taken to an authorized studio immediately. Air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • ...

  • Page 46

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 47

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental seat-mounted side air bags (sab) label 2 things t...

  • Page 48

    Supplemental side air bag inflatable curtain (sabic) supplemental side air bag inflatable curtains (sabic) may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers, placed adjacent to the he...

  • Page 49

    Warning! • your vehicle is equipped with left and right sabic, do not stack luggage or other cargo up high enough to block the location of the sabic. The area where the side curtain air bag is located should remain free from any obstructions. • do not use accessory seat covers or place objects betwe...

  • Page 50

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for the best interaction with the advanced front air bags. Along with seat belts and pretensioners, advanced front air bags and the supplemental driver side knee...

  • Page 51

    Hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. The side air bags will not deploy in all side collisions. Side air bag deployment will depend on the severity and typ...

  • Page 52

    Noted that could affect the air bag system. The diagnos- tics also record the nature of the malfunction. Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the...

  • Page 53

    Requiring the advanced front air bags, it signals the inflator units. A large quantity of non-toxic gas is gener- ated to inflate the supplemental driver side knee air bag. The trim cover separates and folds out of the way allowing the air bag to inflate to the full size. The air bag fully inflates ...

  • Page 54

    The outside edge of the headliner out of the way and covers the window. The air bag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area whe...

  • Page 55

    Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine com- partment and fuel tank before resetting the system and starting the engine. System reset procedure after an impact causing air bag deployment, the left and right turn signal lights, located in...

  • Page 56

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 57

    If a reset procedure step is not completed within 45 seconds, then the turn signal lights will turn off and the reset procedure must be performed again in order to be successful. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/...

  • Page 58

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized studio immediately. Also, have the occupant restraint con- troller (orc) system service...

  • Page 59

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized studio for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 60

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the body control module (bcm) fuse block inside the vehicle for blown fuses. ...

  • Page 61

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Ev...

  • Page 62

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 63

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and tod- dlers children who are two years old or younger and who have not reached the height or weight limits of their child re- straint either an infant carr...

  • Page 64

    Infants and child restraints safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carrie...

  • Page 65

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 66

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 67

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 68

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 69

    Latch positions for installing child restraints in this vehicle what is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the...

  • Page 70

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 71

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 72

    Locating the latch anchorages in addition, there are tether strap anchors lo- cated behind each rear seatback, near to the floor. Latch anchorages 70 things to know before starting your vehicle.

  • Page 73

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 74

    To install a latch-compatible child restraint 1. If the selected seating position has a switchable auto- matic locking retractor (alr) seat belt, stow the seat belt following the instructions below. See the section “installing child restraints using the vehicle seat belt” to check what type of seat ...

  • Page 75

    7. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. How to stow an unused alr seatbelt when using the latch attaching system to install a child restraint, stow all alr seat...

  • Page 76

    Installing child restraints using the vehicle seat belt the seat belts in the passenger seating positions are equipped with either a switchable automatic locking retractor (alr) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight ar...

  • Page 77

    3. Slide the latch plate into the buckle until you hear a “click.” 4. Pull on the webbing to make the lap portion tight against the child seat. 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the w...

  • Page 78

    Better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the car seat. 2. Next, pull enough of the seat belt webbing from the retra...

  • Page 79

    Facing out, away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate...

  • Page 80

    3. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possib...

  • Page 81

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 82

    Safety tips transporting passengers never transport passengers in the cargo area. Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a v...

  • Page 83

    Warning! (continued) • if it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained ...

  • Page 84

    Studio. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized studio. Defroster check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your author...

  • Page 85

    Warning! (continued) • check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal ...

  • Page 86

    Lights have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door latches check for positive closing, latching, and locking. Fluid leaks check area under vehicle after overnight pa...

  • Page 87

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 ▫ inside day/night mirror . . . . . . . . . . . . . . . .89 ▫ automatic dimming mirror — if equipped . . .90 ▫ conversation mirror — if equipped . . . . . . . . .91 ▫ power mirro...

  • Page 88

    ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . .110 ▫ lane change assist . . . . . . . . . . . . . . . . . . . .111 ▫ follow me home/headlight delay . . . . . . . . .111 ▫ front fog lights — if equipped . . . . . . . . . . .111 ▫ interior lights . . . . . . . . . . . . . . . . . . . ...

  • Page 89

    ▫ turning parkview® on or off — with uconnect® 6.5/6.5n . . . . . . . . . . . . . . . . . . .131 ▫ turning camera delay on or off . . . . . . . . . .131 䡵 garage door opener — if equipped . . .132 ▫ before you begin programming homelink® . .133 ▫ programming a rolling code . . . . . . . . . . . . .1...

  • Page 90

    䡵 cargo area features . . . . . . . . . . . . . . . .149 ▫ rear cargo storage features . . . . . .150 䡵 rear window features . . . . . . . . . . . . . .151 ▫ rear window defroster . . . . . . . . . . . . . . . . .151 䡵 roof luggage rack-if equipped . . . . . . .152 88 understanding the features of y...

  • Page 91

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 92

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activa...

  • Page 93

    Conversation mirror — if equipped there is a conversation mirror located at the top of the overhead console. To gain access to the conversation mirror, pull downward on the mirror to the open position. Power mirrors the power mirror controls are located on the driver’s door trim panel. To adjust a m...

  • Page 94

    Move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forwar...

  • Page 95

    Sun visor “slide-on-rod” feature the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is ...

  • Page 96

    Seats front seats front seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move...

  • Page 97

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 98

    Recliner adjustment the recline lever is located on the outboard side of the seat. To recline the seat, lean forward slightly, lift the lever, lean back to the desired position and release the lever. To return the seatback to its normal upright posi- tion, lean forward and lift the lever. Release th...

  • Page 99

    Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • do not ride with the seatback reclined so ...

  • Page 100

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the outer side of the seat. Note: once a heat setting is selected, heat will be felt within two...

  • Page 101

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 102

    While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving may b...

  • Page 103

    Warning! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Fold and tumble rear seat note: • prior to folding the rear seat, it may be necessary ...

  • Page 104

    2. Fold the seatback forward. 3. Locate the seatback recline lever on the outboard side of the seat and lift upward on the lever. 4. Slowly flip the entire seat forward. Seatback folded seatback recline lever 102 understanding the features of your vehicle.

  • Page 105

    5. Slowly flip the entire seat rearward and firmly lock the seat into position. 6. Raise the rear seatback and firmly lock the seatback into position. Rear armrest — if equipped to use the armrest, lower it downward. Folding rear seat folding rear seat armrest 3 understanding the features of your ve...

  • Page 106

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be...

  • Page 107

    Rear head restraints — if equipped the rear seats are equipped with adjustable head re- straints, the outboard head restraints have two adjustable positions and the center head restraint can be stowed when the seat is not in use. When the center seat is being occupied the head restraint should be in...

  • Page 108

    To raise the head restraints, pull upward on the head restraint. To lower the head restraints, press the push button, located at the base of the head restraint, and push downward on the head restraint. Warning! The head restraints for all occupants must be prop- erly adjusted before operating the ve...

  • Page 109

    2. Move to the outside of the vehicle and push the red safety catch lever to the left and raise the hood. The safety catch lever is located under the center front edge of the hood. Hood release lever safety catch lever 3 understanding the features of your vehicle 107.

  • Page 110

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fu...

  • Page 111

    Headlights rotate the end of the multifunction lever up- ward to the first detent for headlight operation. Note: when the headlights are turned on, the daytime running lights will be deactivated. Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the...

  • Page 112

    Note: the low beams and side/tail lights will not be on with drl. The drl function can be turned on or off using the display menus. Refer to “electronic vehicle information center (evic)” in “understanding your instrument panel” for further information. High beams with the low beams activated, pull ...

  • Page 113

    Lane change assist tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash five times then automatically turn off. Follow me home/headlight delay when this feature is selected the driver can choose to have the headlights remain on for a preset ...

  • Page 114

    Using the switch on the bottom of the overhead console, press the switch to the on/right position from its center position and the lights are always on. Press the switch to the off/left position from its center position and the lights are always off. Leave the switch in the center position, and the ...

  • Page 115

    The switches on the left and right sides of the overhead console controls the map or reading function of the lights. Press the switch to the right to turn on the right light and press the switch to the left to turn on the left light. Caution! Before getting out of the vehicle be sure that the switch...

  • Page 116

    Interior light timing (center position) there are four different modes of operation that can be activated in this position: • when one door is opened a three minute timer is activated. • when the key is removed from the ignition (within two minutes of the ignition being turned off), a 10 second time...

  • Page 117

    Windshield wiper off this is the normal position of the wiper lever. Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to the third detent. The wipers will operate at high speed. Manual high speed/mist push the lever upwa...

  • Page 118

    Front windshield washer operation pull the windshield wiper/washer lever toward the steering wheel to activate the washers. The wipers will activate automatically for three cycles after the lever is released. Caution! • turn the windshield wipers off when driving through an automatic car wash. Damag...

  • Page 119

    Rear window wiper/washer activation rotate the windshield wiper lever center ring upwards to operate the rear window wiper as follows: • in intermittent mode when the rear window wiper is not operating. • in synchronous mode (at half the speed of the rear window wiper) when the rear window wiper is ...

  • Page 120

    Pushing the windshield wiper lever forward activates the rear window washer. Keep the windshield wiper lever pushed for more than half a second to activate the rear window wiper as well. Releasing the windshield wiper lever will activate the smart washing function, as de- scribed for the windscreen ...

  • Page 121

    To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the...

  • Page 122

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 123

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 124

    The speed denomination shown is dependant on the speed of english or metric: english speed (mph) • pressing the res (+) button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph. • if the button is continually pressed, the set speed w...

  • Page 125

    • if the button is continually pressed, the set speed will continue to decrease until the button is released, then the new set speed will be established. To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using...

  • Page 126

    Rear park assist is automatically activated when the transmission is placed into reverse. As the distance from an obstacle behind the vehicle decreases, the au- dible alert becomes more frequent. Interaction with trailer towing the rear park assist system is automatically deactivated when a trailer ...

  • Page 127

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 128

    Failure indications a malfunction of the rear park assist sensors or system is indicated, during reverse gear engagement, by the instrument panel warning icon. The warning icon is illuminated and a message is displayed on the multifunction display (if equipped). Refer to “instrument cluster de- scri...

  • Page 129

    • clean the rear park assist sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The rear park assist system might not detect an obstacle behind the f...

  • Page 130

    Warning! • drivers must be careful when backing up even when using parksense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue...

  • Page 131

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the touchscreen display alon...

  • Page 132

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 133

    Turning parkview® on or off — with uconnect® 5.0 1. Turn the radio on. 2. Press the “settings” button. 3. Press the “safety & assistance” soft-key. 4. Press the check box soft key next to “parkview® backup camera” to enable/disable. Note: a check mark will appear in the selection box to indicate the...

  • Page 134

    Taken back to their last radio state. If camera delay is off, the user will be taken directly to their last radio state once in drive. When the vehicle is in drive and the vehicle speed reaches between 9 mph (15 km/h) to 11 mph (18 km/h) the camera images will remain on the screen overlapping the te...

  • Page 135

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 136

    Programming a rolling code for programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “learn” or “train” button located where the hanging antenna is attached to the garage door opener. It is not the button that is normally used to open...

  • Page 137

    2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the homelink® button you wish to pro- gram while keeping the homelink® indicator light in view. 3. Simultaneously press and hold both the homelink® button you want to program and the hand-held trans- mitter button. 4. Continue to hol...

  • Page 138

    Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hold the desired homelink® button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. ...

  • Page 139

    • to program the remaining two homelink® buttons, repeat each step for each remaining button. Do not erase the channels. Reprogramming a single homelink® button to reprogram a channel that has been previously trained, follow these steps: 1. Cycle the ignition to the on/run position. 2. Press and hol...

  • Page 140

    3. Continue to press and hold the homelink® button, while you press and release (“cycle”), your hand-held transmitter every two seconds until homelink® has successfully accepted the frequency signal. The indi- cator light will flash slowly and then rapidly when fully trained. 4. Watch for the homeli...

  • Page 141

    Using homelink® to operate, switch the ignition to the on/run position and the press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-hel...

  • Page 142

    • did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1-800-355-3515 or, on the internet at www.Homelink.Com for information or assistance. Warning! Vehicle exhaust contains carbon monoxide, a danger- ous g...

  • Page 143

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 144

    The power sunroof and power sun blind switches are located in the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle or in a location accessible to children. Occupants, particularly unattended ch...

  • Page 145

    To open pull the power sunroof switch for approximately one second and the sunroof will stop at the vented position. Pull the power sunroof switch a second time for approxi- mately one second and release, the sunroof will open fully, then stop automatically. This is called “express open”. During exp...

  • Page 146

    Power outlets passenger compartment power socket the power outlet is located on the central tunnel, in front of the shift lever, between the two cupholders. It only operates with the ignition key at mar/on. On models with optional ⬙smoker’s kit⬙, the cigar lighter takes the place of the power socket...

  • Page 147

    Note: do not connect devices with power higher than 180 w to the socket. Do not damage the socket by using unsuitable adaptors. Cigar lighter — if equipped this is located on the central tunnel, next to the hand- brake lever. To activate the cigar lighter, press button a. After a few seconds the but...

  • Page 148

    Note: • always check that the cigar lighter is switched off. • do not connect devices with power higher than 180 w to the socket. Do not damage the socket by using unsuitable adaptors. Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seat...

  • Page 149

    Storage glove compartment your vehicle is equipped with a upper and lower glove compartment which is located on the right side of the instrument panel. Pull outward on the glove compart- ment door latch to open either glove compartment. Push the upper glove compartment door down to close it and the ...

  • Page 150

    Front center armrest storage — if equipped the front center armrest contains a storage compartment. To open the storage compartment push in the upper release latch on the front of the armrest. Lift upward on the armrest to gain access to the storage area. The front center armrest can also be lifted ...

  • Page 151

    Cargo area features the rear seatbacks have a fold down feature to allow increased cargo capacity. Push down the release button, located at the outboard top of the seatback and move the seatback to its folded- down position to provide a flat load floor cargo area. When returning the seatback to its ...

  • Page 152

    Rear cargo storage features the rear cargo area has a upper shelf which allows for additional storage below the cargo floor. To raise the cargo floor lift it up by the handle and place it in the rear housing which is located behind the rear seat back. The rear cargo area is equipped with two storage...

  • Page 153

    Rear window features rear window defroster the rear window defroster button is located with the climate controls on the instrument panel. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster...

  • Page 154

    Roof luggage rack-if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 110 lbs (50 kg), and should be uniformly distributed over the luggage rack crossbars. Their are two attachment points inside the door jambs th...

  • Page 155

    Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. Warning! Cargo must be secu...

  • Page 157

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .157 䡵 instrument cluster . . . . . . . . . . . . . . . . .158 䡵 instrument cluster descriptions . . . . .159 䡵 electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . .170 ▫ e...

  • Page 158

    䡵 steering wheel audio controls . . . . . .186 ▫ radio operation . . . . . . . . . . . . . . . . . . . . . .187 ▫ player operation . . . . . . . . . . . . . . . . . . . . . .187 䡵 cd/dvd disc maintenance . . . . . . . . . . .187 䡵 radio operation and mobile phones . .188 䡵 climate controls . . . . ....

  • Page 159

    Instrument panel features 1 — side vent 7 — fixed upper air vent 13 — climate controls 2 — radio controls behind the steering wheel 8 — passenger advanced front air bag 14 — usb port/sd card/aux socket 3 — multifunction lever – light control 9 — upper glove compartment 15 — uconnect® audio system 4 ...

  • Page 160

    Instrument cluster 158 understanding your instrument panel.

  • Page 161

    Instrument cluster descriptions 1. Speedometer the speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h). 2. Cruise on indicator — if equipped this light will turn on when the electronic speed control is on. For further information, refer to “electronic speed ...

  • Page 162

    The esc activation/malfunction indicator light starts to flash as soon as the esc system or tcs system become active. Note: • the esc off indicator light and the esc activation/ malfunction indicator light come on momentarily each time the ignition switch is turned to on/run. • each time the ignitio...

  • Page 163

    Off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized studio. The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that ...

  • Page 164

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If all the segments of the...

  • Page 165

    Service. Refer to “if your engine overheats” in “what to do in emergencies” for further information. 13. High beam indicator this light indicates that the headlights are on high beam. Pull the turn signal lever toward the steer- ing wheel to switch the headlights to low beam. 14. Park/headlight on i...

  • Page 166

    17. Seat belt reminder light when the ignition switch is first turned to on/ run, this light will turn on if the driver’s seat belt is unbuckled, a chime will sound. When driving, if the driver’s seat belt remains unbuckled, the seat belt reminder light will illuminate and the chime will sound. Refe...

  • Page 167

    21. Vehicle security light if during starting, the key code is not correctly recognized, the vehicle security light comes on in the instrument panel. In this case, turn the key to off and then to on/run; if it is still locked, try again with the other keys that come with the vehicle. Contact an auth...

  • Page 168

    Warning! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to...

  • Page 169

    Your vehicle has also been equipped with a tpms malfunction indicator to indicate when the system is not operating properly. The tpms malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and...

  • Page 170

    Seconds. An externally powered electric engine block heater is available as optional equipment or from your authorized studio. The message ⬙plug in engine heater⬙, will be displayed in the instrument cluster when the ambient temperature is below 5°f (-15°c) at the time the engine is shut off as a re...

  • Page 171

    27. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is place...

  • Page 172

    29. Power steering system warning this light is used to manage the electrical warning of the eps (power steering system). When the ignition is turned to the on/run position, the warning light will illuminate mo- mentarily. If the warning light stays on, cycle the ignition to the off position and bac...

  • Page 173

    • date or trip distance display in miles or kilometers • outside temperature • gear indicator • odometer (display of distance travelled in miles/ kilometers) • car status indication (e.G. Doors open, possible ice on road, service, etc.) evic control buttons the evic control buttons are located on th...

  • Page 174

    Electronic vehicle information center (evic) setup menu the menu comprises a series of functions arranged in a cycle. The menu includes the following functions: • speed beep • trip b data • dimmer • autoclose • units • language • buzzer volume • daylights (d.R.L.) • hill start • low tire pressure • ...

  • Page 175

    Briefly press the menu button to select the displayed submenu option and to open the relevant setup menu. Press the up or down button (by single presses) to select the new setting for this submenu option. Briefly press the menu button to store the new setting and go back to the previously selected s...

  • Page 176

    Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as; trip information, range, fuel consumption, average speed and travel time). Trip button the trip button, located on the right steering column stalk, can be u...

  • Page 177

    New trip to reset: • press and hold the trip button to reset the system manually. • when the “trip distance” reaches 9999.9 miles or kilometers or when the “travel time” reaches 999.59 (99 hours and 59 minutes), the system is reset auto- matically. • disconnecting/reconnecting the battery resets the...

  • Page 178

    • average consumption • instant consumption a • average speed a • travel time a (driving time). “trip b” can be used to display the figures relating to: • trip distance b • average consumption b • average speed b • travel time b (driving time). Note: “trip b” functions may be excluded (see “trip b d...

  • Page 179

    Average consumption this value shows the approximate average consumption since the last reset. Instant consumption this indicates the fuel consumption. The value is con- stantly updated. The message “----” will appear on the display if the car is parked with the engine running. Average speed this va...

  • Page 180

    2. Briefly press the menu button to go back to the menu screen or press and hold the menu (approximately one second) to go back to the main screen without storing settings. Speed beep (speed limit) with this function it is possible to set the car speed limit (mph or km/h); when this limit is exceede...

  • Page 181

    2. Press the down button. “off” will flash on the display. 3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the main screen without storing the settings. Speed display when this function is activated the clus...

  • Page 182

    Set date this function may be used to set the date (day - month - year). To change the date proceed as follows: 1. Briefly press the menu button and “year” will flash on the display. 2. Press the up or down button for setting. 3. Briefly press the menu button and “month” will flash on the display. 4...

  • Page 183

    1. Briefly press the menu button “on” or “off” will flash on the display (according to the previous set- ting). 2. Press the up or down button for setting. 3. Briefly press the menu button to go back to the menu screen, or press and hold the menu button (approxi- mately one second) to go back to the...

  • Page 184

    If the distance unit set is “km,” the fuel economy unit will be displayed in either km/l or l/100km. 1. Press the up or down button for setting. 2. Briefly press the menu button to return to the sub-menu. 3. When accessing the “temperature” submenu: briefly press the menu button. Either “°f” or “°c”...

  • Page 185

    Buzzer volume (adjusting the failure/warning buzzer volume) with this function the volume of the buzzer accompany- ing any failure/warning indication can be adjusted to one of eight volume levels. To adjust the volume proceed as follows: 1. Briefly press the menu button. The previously set volume “l...

  • Page 186

    Proceed as follows to switch this function on or off: 1. Briefly press the menu button to display the three sub-menus. 2. Briefly press the menu button. “on” or “off” will flash on the display (according to previous setting). 3. Press the up or down button for setting. 4. Briefly press the menu butt...

  • Page 187

    Press the button to return to the last menu option (daylights). Uconnect® radios for detailed information about your uconnect® radio, refer to your uconnect® supplement manual. Ipod®/usb/sd card/media player control this feature allows an ipod® or external usb device to be plugged into the usb port ...

  • Page 188

    Steering wheel audio controls the remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pr...

  • Page 189

    Radio operation pressing the top of the switch will “seek” up for the next listenable station and pressing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gram...

  • Page 190

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 191

    The manual climate controls consist of a series of rotary dials, an inner push knob and two push buttons. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler...

  • Page 192

    4. A/c button press this button to engage the air conditioning. A light will illuminate when the air conditioning system is engaged. Max a/c for maximum cooling, use the a/c and recirculation modes at the same time. Economy mode if economy mode is desired, press the a/c button to turn off the indica...

  • Page 193

    • mix air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • defrost air is directed through...

  • Page 194

    Air recirculation press and release the air recirculation button, so that the led on the button switch is on, to enter recirculation mode. It is advisable to switch internal air recirculation on while standing in traffic or in tunnels to prevent the introduction of polluted air. Do not use the funct...

  • Page 195

    Air flow to windshield and side windows. Selecting the footwell/windshield or only windshield distribution activates the climate control system com- pressor (led on a/c button on) and the air recirculation is set to ⬙outside air⬙ (led on recirculation control button off ). This logic guarantees opti...

  • Page 196

    System maintenance in winter, the climate control system must be turned on at least once a month for about 10 minutes. Have the system inspected at a fiat studio before the summer. Note: the system uses r134a coolant which does not pollute the environment in the event of accidental leak- age. Under ...

  • Page 197

    1. Driver temperature control provides the driver with independent temperature con- trol. Rotate adjustment knob to set desired temperature. Note: in sync mode, this button will also automatically adjust the passenger temperature setting at the same time. 2. Recirculation control press and release t...

  • Page 198

    6. Blower control blower control is used to regulate the amount of air forced through the climate system. Adjusting the blower will cause automatic mode to switch to manual opera- tion. The speeds can be selected by rotating the blower control adjustment knob. 7. Blower control indicator leds leds i...

  • Page 199

    Temperature setting with the driver temperature setting. Changing the passenger temperature setting while in sync will automatically exit this feature. 12. Auto button automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Performing this function will ca...

  • Page 200

    All these functions can be adjusted manually by operat- ing the system, selecting one or more functions and modifying their parameters. Automatic control of the functions will be suspended: the system will only override the settings for safety reasons. Manual selections always take priority over aut...

  • Page 201

    Note: the climate control system detects the passenger compartment temperature using a mean radiant tem- perature sensor located in the interior rear view mirror and protected by a specific cover. Obstructing the field of view of this sensor with any object could cause the climate control system to ...

  • Page 202

    Adjusting the air temperature rotate the driver temperature control, or the passenger temperature control, dial clockwise or anti clockwise, to adjust the air temperature in the front left (driver tem- perature control) or right (passenger temperature con- trol) zone of the passenger compartment. Th...

  • Page 203

    • down arrow – air flow to the front and rear footwell diffusers. This air distribution setting heats the passen- ger compartment most quickly, giving a prompt sen- sation of warmth. • right/down arrows – air flow distributed between footwell diffusers (hotter air) and central and side dashboard ven...

  • Page 204

    To restore automatic control of the air distribution after a manual selection, press the auto button. Auto button when the auto button is pressed (led on button lit) the climate control system automatically adjusts the follow- ing settings in the corresponding zones: • quantity and distribution of t...

  • Page 205

    To restore automatic system control after one or more manual adjustments, press the auto button. Sync button press the sync button (led on button lit) to align the passenger side air temperature with that of the driver side. This function makes temperature regulation easier when the driver is travel...

  • Page 206

    Note: • the engagement of the recirculation system makes it possible to reach the required heating/cooling condi- tions faster. It is, however, inadvisable to use it on rainy/cold days as it would considerably increase the possibility of the windows misting up inside (espe- cially if the climate con...

  • Page 207

    • the fan speed can be reset manually. With the compressor on and the engine running, manual ventilation cannot be lower than the minimum speed (only one led lit). Note: with the compressor off, air cannot be introduced to the passenger compartment with a temperature lower than the outside temperatu...

  • Page 208

    When the function is activated, the led on the auto button switches off. With the function activated the only possible manual adjustments are adjusting the fan speed and turning the heated rear window off. When the recirculation control, rear defrost control , or auto buttons are pressed, the climat...

  • Page 209

    Switching off the climate control system press the on/off button. With climate control system off: • air recirculation is on, thus isolating the passenger compartment from the outside; • the compressor is off; • the fan is off; • the heated rear window can be activated / deacti- vated. Note: the cli...

  • Page 211

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .213 ▫ manual transmission — if equipped . . . . . . .213 ▫ automatic transmission — if equipped . . . . .213 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .213 ▫ cold weather operation . . . . . . . ....

  • Page 212

    䡵 autostick® — if equipped . . . . . . . . . . . .238 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .238 䡵 driving on slippery surfaces . . . . . . . . .239 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .239 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 213

    ▫ tire terminology and definitions . . . . . . . . . .259 ▫ tire loading and tire pressure . . . . . . . . . . .260 䡵 tires — general information . . . . . . . .265 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .265 ▫ tire inflation pressures . . . . . . . . . . . . . . . . .266 ▫ ti...

  • Page 214

    ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . . .284 ▫ materials added to fuel . . . . . . . . . . . . . . . .285 ▫ fuel system cautions. . . . . . . . . . . . . . . . . . .285 ▫ carbon monoxide warnings . . . . . . . . . . . . .286 䡵 adding fuel . . . . . . . . . . . . . . . . . . . . . ....

  • Page 215

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 216

    Turn the ignition switch to the avv (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Cold weather operation to prevent ...

  • Page 217

    4. If the engine fails to start after 8 attempts, allow the starter to cool for at least 10 minutes, then repeat the procedure. If engine fails to start warning! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result ...

  • Page 218

    On the type of driving and the amount of cargo, the pump will run for up to 10 minutes after the engine has been shut off to circulate coolant through the turbocharger. Although the pump is rubber-mounted for quiet opera- tion, it is normal to hear it running during this time. Manual transmission — ...

  • Page 219

    For most city driving you will find it easier to use only the lower gears. For steady highway driving with light accelerations, sixth gear is recommended. Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will c...

  • Page 220

    When turning a corner, or driving up a steep grade, downshift early so that the engine will not be overbur- dened. Automatic transmission — if equipped caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into park only after the vehicle has come to ...

  • Page 221

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 222

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the full off (key removal) position. The key can only be removed from the ignition when the ignition is in the full off ...

  • Page 223

    This transmission is programmed to prevent shifting from reverse to drive or drive to reverse, if vehicle speed is above 6 mph (10 km/h). This safety feature helps protect your transmission from damage. Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle i...

  • Page 224

    Transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the shift lever to the right (into the drive [d] position) for access to park, reverse, and neutral. Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any...

  • Page 225

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever out of park with the brake pedal released. Make sure the transmission is in park before leaving the vehicle. • it is dangerous to shift out of park or neu...

  • Page 226

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for anum- ber of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking br...

  • Page 227

    • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the...

  • Page 228

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The drive position provides optimum driving characteris- tics under all normal ope...

  • Page 229

    • when frequent transmission shifting occurs (such as when operating the vehicle under heavy loading con- ditions, in hilly terrain, or traveling into strong head winds), use the autostick® shift control (refer to “autostick®” in this section for further information) to select a lower gear. Under th...

  • Page 230

    Message description gear not available in autostick® mode, the gear selected by the driver is not available due to a fault condition. See your authorized studio for diagnosis and service. Shift not allowed the gear position requested by the driver is currently blocked. This oc- curs if: reverse is r...

  • Page 231

    Message description automatic mode not avail- able the transmission is unable to shift itself automatically, due to a fault con- dition. Use the autostick® mode to shift the transmission manually. See your authorized studio for diagnosis and service. Reduce gear changes the transmission pump is over...

  • Page 232

    Message description service shifter a shift lever fault has been detected. See your authorized studio for diag- nosis and service. Engage park brake the sensor that confirms park engagement is not functioning properly. Engage the parking brake to ensure that the vehicle will not roll when in park. T...

  • Page 233

    5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you visit your authorized studio at your earliest possible convenience. Your authorize...

  • Page 234

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and autostick® shift positions. Manual shifts ...

  • Page 235

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it diffi- cult to move the sh...

  • Page 236

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 237

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 238

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 239

    Range of torque converter clutch engagement. This is done to prevent transmission damage due to overheat- ing. During cold temperatures, transmission operation may be modified depending on engine coolant temperature. Normal operation will resume once the engine tempera- ture has risen to a suitable ...

  • Page 240

    If the transmission cannot be reset, authorized studio service is required. Autostick® — if equipped autostick® is a driver-interactive transmission feature providing manual shift control, giving you more control of the vehicle. Autostick® allows you to maximize en- gine braking, eliminate undesirab...

  • Page 241

    Out in second or third gear can be helpful in snow or icy conditions. To select second or third gear after the vehicle is brought to a stop, tap the shift lever rear- ward (+) once or twice. • if a requested downshift would cause the engine to over-speed, that shift will not occur. • avoid using spe...

  • Page 242

    Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose ...

  • Page 243

    Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicl...

  • Page 244

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 245

    Electric power steering this only operates with the key turned to mar/on and the engine started. The steering allows the force required at the steering wheel to be adjusted to suit driving conditions. Note: when turning the ignition key quickly, full power steering functionality can be achieved afte...

  • Page 246

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 247

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized studio immediately. Brake system in the event power assist is lost for any reason (for example; repeated brake applications with th...

  • Page 248

    Warning! • pumping the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • the anti-lock brake system (abs) cannot prevent the natural laws of physics f...

  • Page 249

    Anti-lock brake system (abs) this system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. Refer to “four-wheel anti-lock brake system” in ...

  • Page 250

    Traction control system (tcs) this system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the tcs system functions si...

  • Page 251

    Warning! There may be situations on minor hills with a loaded vehicle, or while pulling a trailer, when the system will not activate and slight rolling may occur. This could cause a collision with another vehicle or object. Always remember the driver is responsible for brak- ing the vehicle. Disabli...

  • Page 252

    Electronic stability control (esc) this system enhances directional control and stability of the vehicle under various driving conditions. Esc cor- rects for oversteering or understeering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the oversteering or und...

  • Page 253

    Esc activation/malfunction indicator light and esc off indicator light the esc activation/malfunction indicator light in the instrument cluster will come on when the ignition switch is turned to the mar (acc/on/run) position for four seconds. If the esc activation/malfunction indicator light comes o...

  • Page 254

    Esc operating modes the esc system has two available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started the system will be in this mode. This mode should be used for most driving situations. Esc should only be turned to “partial off” for specific reas...

  • Page 255

    Note: to improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by momentarily pressing the “esc off” button. Once the situation requiring “partial off” mode is overcome, turn esc back ...

  • Page 256

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 257

    Note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standards. Tires designed to this standard ha...

  • Page 258

    Tire sizing chart example: size designation: p = passenger car tire size based on u.S. Design standards ⴖ....Blank....ⴖ = passenger car tire based on european design standards lt = light truck tire based on u.S. Design standards t or s = temporary spare tire 31 = overall diameter in inches (in) 215 ...

  • Page 259

    Example: service description: 95 = load index — a numerical code associated with the maximum load a tire can carry h = speed symbol — a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — the maximum speed corres...

  • Page 260

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 261

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 262

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 260 starting and operating.

  • Page 263

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 264

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 265

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 266

    264 starting and operating.

  • Page 267

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 268

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 269

    Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflat...

  • Page 270

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 271

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). All sea...

  • Page 272

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 273

    Warning! • temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). • temporary use spare tires have limited tread life. When the tread is worn to the tread wear indica- tors, the temporary use spare tire needs to be replaced. • be sure to foll...

  • Page 274

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do...

  • Page 275

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 276

    Information placard or the vehicle certification label for the size designation of your tire. The load index and speed symbol for your tire will be found on the original equipment tire sidewall. See the tire sizing chart ex- ample found in the tire safety information section of this manual for more ...

  • Page 277

    Warning! (continued) • failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (tract...

  • Page 278

    Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device clearance be- tween tires and other suspension components, it is important that only traction devices in good condi- tion are used. Broken devices can cause serious damage. S...

  • Page 279

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 280

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 281

    Driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68° f (20° c) and the measured tire pressure...

  • Page 282

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 283

    The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. Note: it is particularly important for you to check the tire pressure in al...

  • Page 284

    Pressure monitoring telltale light will turn off when the fault condition no longer exists. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the tpm sensors. 2. Installing some form...

  • Page 285

    Warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is sub...

  • Page 286

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” reformulated gasolines contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of ref...

  • Page 287

    Vehicles. The manufacturer recommends that gasoline without mmt be used in your vehicle. The mmt content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether the gasoline contains mmt. Mmt is prohibited in federal and california reformulated...

  • Page 288

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 289

    Adding fuel 1. Open the fuel filler door. 2. There is no fuel filler cap. A flapper door inside the pipe seals the system. 3. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refuel- ing. Note: only the correct size nozzle opens the latches allowi...

  • Page 290

    Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Warning! • never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • never add fuel when the engine is running. This is in violation of most stat...

  • Page 291

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmis- sion euro twin clutch transmission automatic trans- mission (aisin f21-250 hd transmission ) flat tow none transmission in neutral not allowed not allowed d...

  • Page 292

    Caution! Do not flat tow any vehicle equipped with an automatic or euro twin clutch transmission. Dam- age to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are off the ground. Note: this vehicle may be towed on a flatbed or vehicle trailer provided all four...

  • Page 293

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .293 䡵 if your engine overheats . . . . . . . . . . . .293 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .294 ▫ torque specifications . . . . . . . . . . . . . . . . . . .294 䡵 tirefit...

  • Page 294

    䡵 freeing a stuck vehicle . . . . . . . . . . . . .318 䡵 shift lever override . . . . . . . . . . . . . . . .319 䡵 towing a disabled vehicle . . . . . . . . . . .320 ▫ manual transmission . . . . . . . . . . . . . . . . . . .322 ▫ euro twin clutch transmission. . . . . . . . . . . .322 ▫ automatic t...

  • Page 295

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Press the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Press th...

  • Page 296

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 297

    Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are proper...

  • Page 298

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tirefit kit — if equipped small punctures up to ¼” (6 mm) in the tire tread can be sealed with tirefit. ...

  • Page 299

    Using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. Selec...

  • Page 300

    Tirefit usage precautions • replace the tirefit sealant bottle (1) and sealant hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system. Refer to “sealing a tire with tirefit” section (f) “sealant bottle and hose rep...

  • Page 301

    The vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel is free of debris before connecting the tirefit kit. • you can use the tirefit air pump to inflate bicycle tires. The...

  • Page 302

    Warning! (continued) • keep tirefit away from open flames or heat source. • a loose tirefit kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tirefit kit in the place provided. Failure to follow these warnings can result in injuries that are ...

  • Page 303

    Ground. This will provide the best positioning of the kit when injecting the sealant into the deflated tire and running the air pump. Move the vehicle as necessary to place the valve stem in this position before proceed- ing. 3. Place the transmission in park (auto transmission) or in gear (manual t...

  • Page 304

    Note: sealant may leak out through the puncture in the tire. If the sealant (white fluid) does not flow within 0 – 10 seconds through the sealant hose (6): 1. Press the power button (4) to turn off the tirefit kit. Disconnect the sealant hose (6) from the valve stem. Make sure the valve stem is free...

  • Page 305

    If the tire does not inflate to at least 26 psi (1.8 bar) pressure within 15 minutes: • the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. Note: if the tire becomes over-inflated, press the defla- tion button to reduce the tire pressure to the recom- men...

  • Page 306

    Warning! Tirefit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tirefit. Do not exceed 55 mph (90 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, ...

  • Page 307

    2. Disconnect the tirefit kit from the valve stem, reinstall the cap on the valve stem and unplug from 12 volt outlet. 3. Place the tirefit kit in its proper storage area in the vehicle. 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized studio or tire s...

  • Page 308

    6. Verify that the cap is installed on the fitting at the end of the sealant hose (6) and return the hose to its storage area (located on the bottom of the air pump). 7. Return the tirefit kit to its storage location in the vehicle. Jacking and tire changing — if equipped warning! • do not attempt t...

  • Page 309

    Spare tire removal the spare tire is stowed in underneath the rear cargo area on the outside of the car. 1. Remove the cargo floor to access the winch. 1– tow eye 2– emergency fuel fill funnel 3– jack 4– jack handle 5– tirefit kit 6– emergency flashlight 7– emergency screwdriver spare tire location ...

  • Page 310

    2. Remove the jack handle and use the wrench end to lower the spare tire. 3. When the spare is clear, replace the jack tools. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle clos...

  • Page 311

    6. Block both the front and rear of the wheel diagonally opposite the jack- ing position. For example, if chang- ing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle while the vehicle is being jacked. Jacking instructions warning! Carefully follow th...

  • Page 312

    Warning! (continued) only use the jack in the positions indicated and for lifting this vehicle during a tire change. If working on or near a roadway, be extremely careful of motor traffic. Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking ...

  • Page 313

    Note: there are front and rear jacking locations on each side of the body (as indicated by the traingular lift point symbols on the sill molding). Front jacking location rear jacking location 6 what to do in emergencies 311.

  • Page 314

    4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. 5. Raise the vehicle just enough to remove the...

  • Page 315

    Warning! • to avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. • to avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp...

  • Page 316

    Caution! The winch mechanism is designed for use with the jack wrench extension tool only. Use of air wrench or power tool may damage the winch. Jump-starting procedure if your vehicle has a discharged battery, it can be jump- started using a set of jumper cables and a battery in another vehicle or ...

  • Page 317

    Preparations for jump-start the battery in your vehicle is located on the drivers side of the engine compartment. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove an...

  • Page 318

    3. Remove the protective cover over the remote positive (+) battery post. To remove the cover, pull upward on the cover. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not al...

  • Page 319

    4. Connect the opposite end of the negative (-) jumper cable to the disconnected negative (-) cable on the discharged battery. Warning! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electri- cal spark could cause the battery to explode and could re...

  • Page 320

    Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prev...

  • Page 321

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 322

    3. Using a screwdriver or similar tool, carefully separate the shift lever bezel and boot assembly from the center console. 4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the shift lever override access hole (at the right front corner of th...

  • Page 323

    Towing condition wheels off the ground manual trans- mission euro twin clutch trans- mission automatic transmission flat tow none trans in neutral not allowed not allowed dolly tow rear not allowed not allowed not allowed front ok ok ok flatbed all best method best method best method proper towing o...

  • Page 324

    Manual transmission • vehicle can be flat towed (all four wheels on the ground) with the transmission in neutral. • vehicle can be towed with the front wheels elevated. • vehicle can be towed on a flatbed truck (all wheels off the ground). Caution! Towing this vehicle in violation of the above requi...

  • Page 325

    • vehicle can be towed on a flatbed truck (all wheels off the ground). If the ignition key is unavailable, or the battery is discharged, see “shift lever override” in “what to do in emergencies” for instructions on shifting the automatic transmission out of park for towing. Caution! • do not flat to...

  • Page 327

    Maintaining your vehicle contents 䡵 engine compartment — 1.4l turbo . . . .327 䡵 onboard diagnostic system — obd ii . .328 䡵 replacement parts . . . . . . . . . . . . . . . . . .328 䡵 studio service . . . . . . . . . . . . . . . . . . . . . .329 䡵 maintenance procedures . . . . . . . . . . .329 ▫ en...

  • Page 328

    ▫ automatic transmission — aisin f21-250 hd transmission — if equipped . . . . . . . . . . . . .355 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . .356 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .363 ▫ underhood fuses. . . . . . . . ....

  • Page 329

    Engine compartment — 1.4l turbo 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — front distribution unit (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 7 maintaining your vehicle 327.

  • Page 330

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and euro twin clutch transmission control systems. When these sys- tems are operating properly, your vehicle will p...

  • Page 331

    Studio service your authorized studio has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 332

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 333

    Caution! Do not overfill the engine with oil. Overfilling the engine with oil will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This loss of oil pressure and increased oil temperature could damage your engine. Change engine oil the oil change indicat...

  • Page 334

    Engine oil filler cap location, refer to “engine compart- ment” in “maintaining your vehicle” for further informa- tion. Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an eng...

  • Page 335

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 336

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 337

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized studio at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 338

    Protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized studio or other service facilities using recovery and recycling equipment. Note: use only manufacturer approved a/c system pag compressor oil and refriger...

  • Page 339

    5. Open the air filter access door. 6. Remove the particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing. 7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. A/c air filter access door...

  • Page 340

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 8. Rotate the glove compartment door back into position. Refer to the “maintenance schedule” for the prop...

  • Page 341

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make s...

  • Page 342

    4. Install the wiper blade and firmly press the wiper blade until it snaps into place. Rear wiper blade removal/installation 1. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin...

  • Page 343

    Adding washer fluid the windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with wind- shield washer solvent (not engine coolant/ antifreeze). Refer to “engine compartment” in “maintaining your vehicle...

  • Page 344

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 345

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 346

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 347

    Note: some vehicles require special tools to add cool- ant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your local authorized studio. Selection of coolant refer to “fluids, lubricants, ...

  • Page 348

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 349

    (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area whe...

  • Page 350

    Warning! • the warning words “do not open hot” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To pre...

  • Page 351

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 352

    Only the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “mai...

  • Page 353

    Note: if your vehicle is equipped with a manual trans- mission , the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system. The manual transmission clutch ...

  • Page 354

    Warning! (continued) • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lowe...

  • Page 355

    Manual transmission — if equipped lubricant selection use only the manufacturers recommended transmission fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Fluid level check check the fluid level by removing the fill plug. The fluid level ...

  • Page 356

    Transmission fluid is an engineered product and its performance may be impaired by supplemental addi- tives. Therefore, do not add any fluid additives to the transmission. The only exception to this policy is the use of special dyes for diagnosing fluid leaks. Caution! Do not use chemical flushes in...

  • Page 357

    Maintenance schedule. In addition, change the fluid if it becomes contaminated (with water, etc.), or if the trans- mission is disassembled for any reason. Automatic transmission — aisin f21-250 hd transmission — if equipped selection of lubricant it is important to use the proper transmission fluid...

  • Page 358

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating cond...

  • Page 359

    Passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and...

  • Page 360

    Caution! • do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • use of power washers exceeding 1,200 psi (8 274 kpa) can result in damage or removal of paint and decals. • if the engine compartment is washed with an hi...

  • Page 361

    Wheel and wheel trim care • all wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • to remove heavy soil and/or excessive brake dust, use mopar® wheel cleaner. Note: if your vehicle is equipped with dark ...

  • Page 362

    • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap resid...

  • Page 363

    Caution! Do not use alcohol and alcohol-based and/or keton based cleaning products to clean leather seats, as damage to the seat may result. Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratc...

  • Page 364

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 365

    Fuses warning! • when replacing a blown fuse, always use an ap- propriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 366

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Cav...

  • Page 367

    Cavity maxi fuse mini fuse description f07 50 amp red radiator fan - high speed f08 40 amp orange blower motor f09 7.5 amp brown transmission f10 15 amp blue horn f11 10 amp red powertrain f14 20 amp yellow power outlet 115v f15 15 amp blue transmission cavity maxi fuse mini fuse description f16 7.5...

  • Page 368

    Cavity maxi fuse mini fuse description f24 7.5 amp brown stability control system f30 5 amp tan after run pump f81 70 amp tan ptc (secondary) f82 40 amp orange transmission f83 40 amp orange ptc (primary) cavity maxi fuse mini fuse description f84 7.5 amp brown transmission f85 15 amp blue front pow...

  • Page 369

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Cavity vehicle fuse num- ber mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 7.5 amp brown front and rear ceil- ing lights trunk and door cou...

  • Page 370

    Cavity vehicle fuse num- ber mini fuse description 5 f36 15 amp blue diagnostic socket, car radio, climate control system, tpms, sunroof 6 f43 20 amp yellow bi-directional washer 7 f48 20 amp yellow passenger power window 8 f13 7.5 amp brown left low beam, headlamp leveling cavity vehicle fuse num- ...

  • Page 371

    Cavity vehicle fuse num- ber mini fuse description 12 f49 5 amp tan exterior mirror, gps, electric mirror, park- ing sensor 13 f31 5 amp tan climate control, seat regulation 14 f47 20 amp yellow driver power win- dow rear interior fuses the rear interior fuse panel is located on the driver’s side in...

  • Page 372

    Cavity vehicle fuse number mini fuse description 1 f61 15 amp blue lumbar regulation seats 2 f62 15 amp blue heated seats 3 f64 20 amp yellow hi fi system 4 f65 20 amp yellow sun blind 5 f66 20 amp yellow sunroof 6 f90 7.5 amp brown left high beam cavity vehicle fuse number mini fuse description 7 f...

  • Page 373

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (e.G., vacation) for two weeks or more, run the air c...

  • Page 374

    Exterior bulbs bulb number front low and high beam headlamp hir2ll front turn signal lamps wy21w front parking/daytime running lamps w21/5w front side marker lamps led (see authorized studio) rear tail/stop lamps p21/5w rear tail lamp led (see authorized studio) rear turn signal lamps p21w rear back...

  • Page 375

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps low beam and high beam 1....

  • Page 376

    2. Rotate the bulb counter-clockwise. 3. Remove the bulb when all the tabs are aligned with the openings in the metal holder. 4. Disconnect the electrical connector from the bulb. Bulb removal procedure electrical connector removal 374 maintaining your vehicle.

  • Page 377

    5. Install the new bulb and rotate clockwise to lock in place. 6. Reinstall the plastic cap. New bulb installation headlamp sealing cap installation 7 maintaining your vehicle 375.

  • Page 378

    Front turn signal, parking and daytime running lamps 1. Turn front wheels inboard to access upper cover in wheel liner. 2. Open the upper cover on the front of the wheel liner. 3. Remove the cap from the back of the lower headlamp housing. 4. Rotate the bulb counter clockwise and remove. 5. Install ...

  • Page 379

    5. Remove the two screws that secure the backplate to the tail lamp housing. 6. Separate the backplate from the tail lamp housing. 7. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 8. Remove the backup lamp bulb by pulling straight out. 9. Replace...

  • Page 380

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant - 1.4l turbo engine we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standar...

  • Page 381

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c635 ddct/mtx transmission fluid euro twin clutch transmission – if equipped use only mopar® c635 ddct/mtx transmission fluid or equivalent. Failure to use the correct fluid may affect t...

  • Page 383

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .382 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .384 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 384

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate in th...

  • Page 385

    Required maintenance intervals . Refer to the maintenance schedules on the following page for the required maintenance intervals. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even ...

  • Page 386

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 387

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 388

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 389

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .388 ▫ prepare for the appointment. . . . . . . . . . . . .388 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .388 ▫ be reasonable with requests ....

  • Page 390

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 391

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized studio service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 392

    (tty) in the united states, can communicate with the manufacturer by dialing 1–800–380–chry. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewriter users, dial 711 and for voice callers, dial 1-800-8...

  • Page 393

    Warning! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear con...

  • Page 394

    West building, washington, d.C. 20590. You can also obtain other information about motor vehicle safety from http://www.Safercar.Gov. In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to repor...

  • Page 395

    Problems the first time, using step-by-step troubleshoot- ing and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment. Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with...

  • Page 396

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 397

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 399

    Index 10

  • Page 400

    Adding engine coolant (antifreeze) . . . . . . . . . . . .346 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .341 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .285 airbag. . . . . . . . . ....

  • Page 401

    Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 jump starting . . . . . . . . . . . . . . . . . . . . . . . . . .314 belts, seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 body mechanism lubrication . . . . . . . . . . . . . . . . .338 b-pillar locat...

  • Page 402

    Clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .284 cleaning wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 windshield wiper blades . . . . . . . . . . . . . . . . . .338 clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 clutch flu...

  • Page 403

    Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 driving through flowing, rising, or shallow standing water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 electric remote mirrors. . . . . . . . . . . . . . . . . . . . . .91 electronic brake control system ....

  • Page 404

    Gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . .222 event data recorder . . . . . . . . . . . . . . . . . . . . . . . .58 exhaust gas caution. . . . . . . . . . . . . . . . . . . . . . . .27 exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . .80 exterior lights . . ....

  • Page 405

    Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .283 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . .377 fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .287 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .363 garage door...

  • Page 406

    Information center, vehicle . . . . . . . . . . . . . . . . . .170 inside rearview mirror . . . . . . . . . . . . . . . . . . . . . .89 instrument cluster . . . . . . . . . . . . . . . . . . . . . . . .159 instrument panel and controls . . . . . . . . . . . . . . . .157 instrument panel cover . . . ...

  • Page 407

    Malfunction indicator (check engine) . . . . . . . . .165 oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . .164 park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 seat belt reminder . . . . ...

  • Page 408

    Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 modifications/alterations, vehicle . . . . . . . . . . . . . . .8 monitor, tire pressure system . . . . . . . . . . . . . . . .278 multi-function control lever . . . . . . . . . . . . . . . . .109 new vehicle break-in period . . ...

  • Page 409

    Power mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 power steering fluid . . . . . . . . . . . . . . . . . . . . . . .379 pregnant wo...

  • Page 410

    Seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . . .39 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 and pregnant women . . . . . . . . . . . . . . . . . . . . .40 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .59 inspection . . . . ...

  • Page 411

    Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .371 storage, vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . .371 storing your vehicle . . . . . . . . . . . . . . . . . . . . . . .371 stuck, freeing. . . . . . . . . . . . . . . . . . . . . . . . . . . .318 studio se...

  • Page 412

    Tread wear indicators . . . . . . . . . . . . . . . . . . . .272 tire safety information . . . . . . . . . . . . . . . . . . . . .254 towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288 disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . .320 recreational . . . . . ....

  • Page 413

    Wait to start light. . . . . . . . . . . . . . . . . . . . . . . . .167 warning lights (instrument cluster description) . . .159 warnings and cautions. . . . . . . . . . . . . . . . . . . . . . .7 warranty information . . . . . . . . . . . . . . . . . . . . . . . .4 washer adding fluid . . . . . . ....

  • Page 414

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be in- stalled properly by trained personnel. The following must be obs...

  • Page 415

    Chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 fia t 500l 14bf-126-ac third edition printed in u.S.A. Fiat 500l.