1. DL manuals
  2. Fiat
  3. Automobile
  4. 500X 2017
  5. Owner's Manual

Fiat 500X 2017 Owner's Manual

Summary of 500X 2017

  • Page 1

    O w n e r ’ s m a n u a l 2 0 1 7 2017 fia t ® 500x fiat ® 500x first edition printed in u.S.A. ©2016 fca us llc. All rights reserved. Fiat is a registered trademark of fca group marketing s.P.A., used under license by fca us llc. 17fb-126-ab.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 customer assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . .5 䡵 vehicle modifications/alterations . . .6 䡵 rollover warning . . . . . . . . . . . . . . . . . .6 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, dis- tinctive styling, and high quality. This owner’s manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenanc...

  • Page 7

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision, bodily injury and/or death. It also contains cau- tions against procedures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may mi...

  • Page 8

    Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Rollover warning utility vehicles have a significantly higher rollover rate than other ty...

  • Page 9

    Customer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .8 ▫ prepare for the appointment . . . . . . . . . . . . .8 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .8 ▫ be reasonable with requests. . . . . . . . . ....

  • Page 10

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to bring the right papers with you, as well as your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the ser- vice...

  • Page 11

    Any communication to the manufacturer’s customer center should include the following information: • owner’s name and address • owner’s telephone number (home and office) • authorized dealer name • vehicle identification number (vin) • vehicle delivery date and mileage fiat customer center p.O. Box 2...

  • Page 12

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 13

    Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and cer...

  • Page 14

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are accepted. Service manuals these comprehensive service manuals provide the in- formation that students and profession...

  • Page 15

    Graphical table of contents contents 䡵 front view . . . . . . . . . . . . . . . . . . . . . . . . .14 䡵 rear view . . . . . . . . . . . . . . . . . . . . . . . . . .15 䡵 instrument panel . . . . . . . . . . . . . . . . . . .16 䡵 interior. . . . . . . . . . . . . . . . . . . . . . . . . . . .17 3.

  • Page 16

    Front view front view 1 — engine compartment 2 — headlights 3 — windshield 4 — outside mirrors 5 — doors 6 — wheels 14 graphical table of contents.

  • Page 17

    Rear view rear view 1 — rear lights 2 — rear windshield wiper 3 — liftgate 3 graphical table of contents 15.

  • Page 18

    Instrument panel instrument panel 1 — air vents 7 — upper switch bank 13 — lower switch bank 2 — multifunction lever 8 — upper storage compartment 14 — driver side knee air bag 3 — instrument cluster 9 — passenger front air bag 15 — ignition 4 — speed controls 10 — air vents 16 — driver side front a...

  • Page 19

    Interior interior features 1 — power window switches 2 — headlight switch 3 — instrument cluster 4 — uconnect radio 5 — glove compartment 6 — seats 7 — climate controls 8 — transmission gear selector (automatic/manual options) 9 — electronic speed controls 10 — instrument cluster display controls 3 ...

  • Page 21

    Getting to know your vehicle contents 䡵 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 ▫ electronic key fob . . . . . . . . . . . . . . . . . . . .23 ▫ key fob operation . . . . . . . . . . . . . . . . . . . .24 ▫ replacing the battery in the key fob with remote control. . . . ...

  • Page 22

    䡵 doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 ▫ manual locking/unlocking . . . . . . . . . . . . . .36 ▫ central lock/unlock. . . . . . . . . . . . . . . . . . .37 ▫ keyless enter-n-go . . . . . . . . . . . . . . . . . . .38 ▫ child locks . . . . . . . . . . . . . . . . . . . ....

  • Page 23

    ▫ high beams . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . .70 䡵 interior lights . . . . . . . . . . . . . . . . . . . . .70 ▫ front courtesy light . . . . . . . . . . . . . . . . . . .70 ▫ rear dome light — if equipped . . . . . . ....

  • Page 24

    ▫ cargo area features . . . . . . . . . . . . . . . . . .107 䡵 internal equipment . . . . . . . . . . . . . . . .110 ▫ glove compartments . . . . . . . . . . . . . . . . . .110 ▫ sun visors “slide-on-rod” . . . . . . . . . . . . .111 ▫ power outlets . . . . . . . . . . . . . . . . . . . . . .112 ▫ c...

  • Page 25

    Keys electronic key fob on versions equipped with ⬙keyless enter-n-go,⬙ the car is equipped with an electronic key fob. The key fob with remote control contains a remote keyless entry key fob. The remote keyless entry system allows you to lock or unlock the doors and liftgate or activate the panic a...

  • Page 26

    Key fob operation unlocking doors and liftgate the driver’s door may be unlocked by inserting the vehicle key into the exterior driver’s door lock cylinder. To unlock all the doors, push the interior power door unlock button on the door panel. Push and release the unlock button on the key fob once t...

  • Page 27

    Locking doors and liftgate the doors may be locked by inserting the vehicle key into the exterior driver’s door lock cylinder. Push and release the lock button on the key fob to lock all doors and liftgate. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Settings...

  • Page 28

    2. Separating key fob halves requires screw removal (if equipped) and gently prying the two halves of the key fob apart with the emergency key. Make sure not to damage the seal during removal. 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a ...

  • Page 29

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unat- tended. • for vehicles equipped with keyless enter-n-go — ignition, always remember to place the igni- tion in the off mode. Duplication of key fobs may be performed at an autho- rized dealer. Th...

  • Page 30

    Note: if the ignition switch does not change with the push of a button, the key fob may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the key fob against the engine start/stop butt...

  • Page 31

    Warning! (continued) • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Chil- dren should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near th...

  • Page 32

    The remote starting system also activates the climate control and (if equipped) the optional heated seats and optional heated steering wheel depending on tempera- tures outside and inside the car. Note: • the vehicle must be equipped with an automatic transmission to be equipped with remote start. •...

  • Page 33

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Car- bon monoxide is poisonous and can cause serious injury or death when inhaled. • keep key fobs away from children. Operation of the remote st...

  • Page 34

    Remote start comfort systems — if equipped when remote start is activated, the heated steering wheel and driver heated seat features will automati- cally turn on in cold weather. These features will stay on through the duration of remote start or until the ignition switch is cycled to the on/run pos...

  • Page 35

    Operate the vehicle. The system will not allow the engine to crank if an invalid key fob tries to start the engine. After placing the ignition to the on/run position, if there is a problem with the system, the vehicle security light will turn on. This condition will result in the engine being shut o...

  • Page 36

    If something triggers the alarm, the vehicle security alarm will provide the following audible and visible signals: • horn will pulse. • park lamps and/or turn signals will flash. • vehicle security light in the instrument cluster will flash. To arm the system follow these steps to arm the vehicle s...

  • Page 37

    Note: • if a second chime is heard after approximately four seconds from arming the alarm, disarm the alarm by pushing the unlock button. Check for the correct closure of doors and liftgate, then reactivate the system by following steps 1 and 2. • if a second chime is heard after approximately four ...

  • Page 38

    Disabling to completely disable the alarm (e.G. In the case of long inactivity of the car), lock the doors by turning the vehicle key in the exterior door lock cylinder. Note: if the batteries in the key fob discharge in the event of a failure to the system, or to switch off the alarm, place the ign...

  • Page 39

    Warning! • when leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be ...

  • Page 40

    The doors can also be locked and unlocked with the keyless enter-n-go (passive entry) system if equipped. For further information, refer to “keyless enter-n-go” in “getting to know your vehicle.” if you push the power door lock switch while the ignition is in the on/run position, and any front door ...

  • Page 41

    • if the vehicle is unlocked by the passive entry door handle, and no door goes ajar within 60 seconds, the vehicle will re-lock and if equipped, the security alarm will arm. • the key fob may not be able to be detected by the vehicle keyless-go system if it is located next to a mobile phone, laptop...

  • Page 42

    Note: all doors will unlock when the front passenger door handle is grabbed regardless of the driver’s door unlock preference setting (“unlock driver door 1st press” or “unlock all doors 1st press”). To lock the vehicle’s doors and liftgate with one of the vehicle’s passive entry key fob within 5 ft...

  • Page 43

    Fobik-safe only executes in vehicles with passive entry. There are three situations that trigger a fobik- safe search in any passive entry vehicle: • a lock request is made by a valid passive entry key fob while a door is ajar. • a lock request is made by the passive entry door handle while a door i...

  • Page 44

    Note: the emergency key can be inserted into the door lock cylinder in either direction. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severel...

  • Page 45

    To unlock/enter the liftgate the liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid passive entry key fob within 3 ft (1.0 m) of the liftgate, push the electronic liftgate release to open with one fluid mo- tion. Note: if “unlock all doors 1st press” is...

  • Page 46

    Note: the liftgate passive entry lock button will only lock the liftgate. The liftgate unlock feature is built into the electronic liftgate release. Activation/deactivation of keyless enter-n-go keyless enter-n-go can be activated or deactivated through the instrument cluster display or through the ...

  • Page 47

    Note: • when the child lock system is engaged, the door can only be opened by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 48

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 49

    Reached the desired position. Then, using body pres- sure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might...

  • Page 50

    Power adjustment front seats — if equipped the power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/ rearward, tilt if equipped and to set the angle of the seatback. Forward or rearward adjustment the seat can be adjus...

  • Page 51

    Power lumbar adjustment push the switch forward or rearward to increase or decrease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support. Heated seats — if equipped the heated seat switches are located on the instrument panel. You can choose between two heating...

  • Page 52

    Rear seats the split rear seat increases the storage of the rear cargo area. Note: • prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and positioned forward, this will allow the rear seat to ...

  • Page 53

    Removing shelf — if equipped proceed as follows: 1. Disconnect the two links that support the shelf at the eyelets. 2. Lift the rear part of the overhead luggage shelf. 3. Clear the pins placed outside of the shelf, and then remove the rear shelf pulling it upwards. 4. The rear shelf can be stored i...

  • Page 54

    4. Pull the seatback release lever to fold the left or right rear seatback completely forward. Cargo area enlargement folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully lower the rear seat head ...

  • Page 55

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stabil- ity for child seats and/or passengers. An improperly latched seat could cause serious injury. Head restraints head restraints are ...

  • Page 56

    Restraint as far as it can go then push the release button and adjustment button at the base of each post while pulling the head restraint up. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then adjust it to the appropriate height. Note: do not reposi...

  • Page 57

    To remove the head restraint, raise it as far as it can go then push the release button and adjustment button at the base of each post while pulling the head restraint up. To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then adjust it to the appropriat...

  • Page 58

    To unlock the steering column, push the tilt/telescoping lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steeri...

  • Page 59

    Auto on comfort — if equipped if the external temperature is below 40 °f (5 °c) at each start-up of the vehicle the heated steering wheel func- tionality is turned on. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabe- tes, spinal cord injury,...

  • Page 60

    When the dimming feature is activated. The sensor to the right of the button does not illuminate. Note: this feature is disabled when the vehicle is moving in reverse. Outside mirrors power adjustment mirrors the power mirror switch is located on the driver’s door panel. To adjust the mirror, push t...

  • Page 61

    Folding mirror the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rearward. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activat...

  • Page 62

    Vehicle is in any forward gear or reverse and enters stand-by mode when the vehicle is in park. The bsm detection zone covers approximately one lane width on both sides of the vehicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approxi- mately 20 ft (6 m) beyond the rear b...

  • Page 63

    The bsm system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The bsm system will issue an alert during these types of zone entries. Entering from the side vehicles that move into your adjacent lanes from either side o...

  • Page 64

    Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 31 mph (50 km/h). Overtaking traffic if you pass another vehicle slowly with a relative speed less than 15 mph (25 km/h) and the vehicle remains i...

  • Page 65

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foli- age, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The bsm system will not alert you of objects...

  • Page 66

    Rear cross path (rcp) the rear cross path (rcp) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The rcp system will th...

  • Page 67

    Mode of operation three selectable modes of operation are available in the uconnect system. Refer to “uconnect settings” in “multimedia” for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm system will provide a visual alert in the appropriate side v...

  • Page 68

    Blind spot monitoring fault warnings sensor blinded in the case of a sensor blinded: • bsm mirror warning lights are turned on continu- ously. • a instrument cluster message will display “blind spot monitoring unavailable - wipe rear bumper corners.” note: the rear bumper must be clean and free of a...

  • Page 69

    Operation of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instrument cluster and interior lighting. Turning on the headlights will illuminate the instru- ment cluster and the controls located on the instrument panel. Automatic lighting — if equipped l...

  • Page 70

    Daytime running lights (drl) — if equipped the daytime running lights (drls) will turn on when the engine is started and remain on unless the head- lights are turned on or the engine is shut off. The drls will be disabled during turn signal operation and resume operation when the turn signal operati...

  • Page 71

    Turn off the headlights within two minutes. The delay interval begins when the headlight switch is turned off. Headlight delay disable the feature is disabled by turning on the headlights, the parking lights or by placing the ignition in run mode. If you shut off the lights before the ignition is tu...

  • Page 72

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. When the daytime running lights are on and a turn signal is activated, the daytime running lamp will turn off on the sid...

  • Page 73

    Note: • before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • if a light is left on it will automatically be turned off after approximately 15 minutes after the ignition is in stop mode. Dome light t...

  • Page 74

    The dome light timing is disabled when the doors are locked. Illuminated vanity mirrors — if equipped an illuminated vanity mirror is located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror c...

  • Page 75

    Rear dome light — if equipped push the switch on the rear dome light once to turn the light on, the light will remain on at all times. Push the switch a second time to turn the light off, the lights will remain off until a door is opened. Vehicles with retractable roof for vehicles equipped with a r...

  • Page 76

    Note: in order to preserve the life of the battery, the light will turn off after 15 minutes. Instrument panel dimmer and ambient light control rotate the ambient dimmer control upward or down- ward to increase or decrease the brightness of the ambient light located in the overhead console, door han...

  • Page 77

    Wipers and washers front wiper operation the windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Caution! Always remove any buildup of snow that prevents the windshiel...

  • Page 78

    If the lever is pulled while the wipers are in the off position, the wipers will operate for several wipe cycles, then turn off. Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind...

  • Page 79

    Wiper sensitivity. Setting two can be used if the driver desires more sensitivity. Place the wiper switch in the off (o) position when not using the system. Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature may no...

  • Page 80

    Rear window wiper/washer the rear wiper/washer controls are located on the lever on the right side of the steering column. The rear wiper/washer is operated by rotating a switch, located at the middle of the lever. Rotate the center portion of the lever upward to the first detent for intermittent op...

  • Page 81

    Minutes. To manually shut the defroster off, push the button a second time. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft...

  • Page 82

    Climate controls air outlet and diffuser locations — passenger compartment left side air outlets 1 — fixed air outlet 2 — adjustable air outlet 3 — air vane adjustment 4 — air flow outlet adjustment center air outlets 1 — air flow outlet adjustment 2 — adjustable air outlet 3 — air vane adjustment 8...

  • Page 83

    Manual climate controls overview right side air outlets 1 — fixed air outlet 2 — adjustable air outlet 3 — air vane adjustment 4 — air flow outlet adjustment manual climate controls 4 getting to know your vehicle 81.

  • Page 84

    Manual climate control descriptions icon description max a/c setting max a/c sets the system for maximum cooling performance. Rotate the temperature con- trol adjust knob counterclockwise to the max a/c setting. In max a/c, the blower speed and mode position can be adjusted to desired user settings....

  • Page 85

    Icon description front defrost mode air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side window de- frosting. Note: the air conditioning compressor operates in mix or defrost, even if the air ...

  • Page 86

    Icon description panel mode panel mode air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. The center instrument panel outlets can be adjusted so that they are directed toward the rear seat passengers for maximum airflow to the rear. Bi-level...

  • Page 87

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping paral- lel to the heating element...

  • Page 88

    System maintenance in winter, the climate control system must be turned on at least once a month for approximately 10 minutes. Have the system inspected at an authorized dealer before the summer. Note: the system uses r-1234yf (refrigerant) which does not pollute the environment in the event of acci...

  • Page 89

    Automatic climate control descriptions icon description max a/c setting max a/c sets the system for maximum cooling performance. Rotate the driver tempera- ture control adjust knob counterclockwise for max a/c. Both driver and passenger tem- perature displays will show max a/c lo. In max a/c, the bl...

  • Page 90

    Icon description recirculation button push to change the current setting. The led illuminates when on. Note: • when in max defrost mode, the recirculation button will change the setting to normal defrost mode. This indicates that you can not enter to this mode due to fogging risk. • when the auto in...

  • Page 91

    Icon description rear defrost button push the rear defrost button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 20 minutes. Passenger temper...

  • Page 92

    Icon description panel mode panel mode air comes from the outlets in the instrument panel. Each of these outlets can be individu- ally adjusted to direct the flow of air. The air vanes of the center outlets and outboard out- lets can be moved up and down or side to side to regulate airflow direction...

  • Page 93

    Icon description mix mode mix mode mix mode is obtained by pressing both the windshield mode button and the floor mode button, activating them both. Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra he...

  • Page 94

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping paral- lel to the heating element...

  • Page 95

    The climate control system carries out the following operations: • turns on the air conditioning compressor when en- vironmental conditions are suitable. • turns air recirculation off. • sets blower fan to the maximum speed. • directs air flow to windshield and front side window diffusers. • activat...

  • Page 96

    Turning off the climate control system push the on/off button. With the climate control system off: • air recirculation is on, isolating the passenger com- partment from the outside. • the a/c compressor is off. • the blower is off. • the heated rear window can be activated/ deactivated. Note: the c...

  • Page 97

    3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to function automatically. Note: • it is not necessary to move the temperature settings. The system automatically adjusts the tem...

  • Page 98

    Winter operation to ensure the best possible heater and defroster perfor- mance, make sure the engine cooling system is func- tioning properly and the proper amount, type, and concentration of coolant is used. Use of the air recir- culation mode during winter months is not recom- mended, because it ...

  • Page 99

    Operating tips chart 4 getting to know your vehicle 97.

  • Page 100

    Windows driver’s door controls the power window switch is located on the driver’s door panel. The driver’s power window switch controls the operation of all the windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls ...

  • Page 101

    Auto-down feature — if equipped the driver and passenger power window switches have an auto-down feature. Push the switch for half a second and release it; the window will go down automatically. To partially open the window, push the window switch and release it when you want the window to stop. To ...

  • Page 102

    Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any impact due to rough road conditions may trig- ger the auto-reverse function unexpectedly during auto-clos...

  • Page 103

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle or in a location acces- sible to children. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunr...

  • Page 104

    Closing the sunroof to close the front panel completely, pull the sunroof switch from the open position. The sunroof can be stopped in any position by pulling the sunroof switch a second time while it is closing. Note: during the open/close or vent operation any push on the switches will stop the cl...

  • Page 105

    Caution! • when refitting sunroof, be careful to avoid fin- gers, scarves, ties and items of clothing from getting caught under the panel. • do not open the roof in the presence of snow or ice. There is risk of damage. Power sunroof relearn procedure as a result of any abnormal behavior of the roof ...

  • Page 106

    Hood opening the hood release lever (to open the primary latch) and safety latch (to open the secondary latch) must be released to open the hood. 1. Pull the hood release lever located under the driver’s side of the instrument panel. 2. Move to the outside of the vehicle. 3. Push the safety latch re...

  • Page 107

    Note: • before lifting the hood, check that the wiper arms are not in motion and not in the lifted position. • while lifting the hood, use both hands. • vehicle must be at a stop and the automatic trans- mission must be in park. Manual transmission vehicles must have the electric park brake engaged....

  • Page 108

    Liftgate the liftgate release function is disabled when the ve- hicle is in motion. Opening opening from outside to unlock the liftgate from the outside, squeeze the electronic liftgate release and pull the liftgate open with one fluid motion. When opening the door, the turn signal lights will flash...

  • Page 109

    3. Insert the screwdriver into the release tab slot to trigger the release tab of the liftgate. Closing grasp the liftgate closing handle and lower the liftgate. Note: before closing the liftgate, make sure to be in possession of the key because the liftgate will be locked automatically. Cargo area ...

  • Page 110

    Position 1 (floor flush): this position allows you to make the load floor flat for ease of loading/unloading objects from the cargo area. This position also makes it possible to use the space below as another compartment for storing fragile or smaller objects. Position 2 (elevated position): when th...

  • Page 111

    Caution! The load floor must be arranged in a central posi- tion with respect to cargo area. Displacement load floor to position the load from the lower to the upper position, proceed as follows: 1. Grasp the load floor handle and lift up the load floor. 2. Correctly place the load floor on the side...

  • Page 112

    Cargo box — if equipped the cargo area contains a preformed cargo box that can be used for the storage of objects that allows you to obtain a uniform level when loading. Note: the cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg). Internal equipment glove comp...

  • Page 113

    Lower glove compartment to open the lower glove compartment, pull outward on the latch and lower the glove compartment door. Once the glove compartment is open, a light will turn on to illuminate the compartment. Note: • do not insert objects in the glove compartments that will not allow the compart...

  • Page 114

    Extendible sun visor to extend the sun visor, proceed as follows: 1. Place the sun visor against the door glass by detach- ing it from the hook and turning it toward the side window. 2. Slide the visor. 3. Slide out the sun visor extender. Power outlets the front power outlet is located under the ce...

  • Page 115

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 116

    After a few seconds, the lighter automatically returns to its initial position and is ready to be used. Warning! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Caution! Do not conn...

  • Page 117

    Ashtray — if equipped note: ashtrays can be purchased at an authorized dealer through mopar parts. The ashtray is a plastic container that can be placed into one of the cup holders. Front armrest the front armrest is located between the front seats. The armrest can be adjusted by moving it in the di...

  • Page 118

    Push the storage handle and lift up the armrest to access the storage compartment. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cupholders there are two cupholders for th...

  • Page 119

    Grab handles the grab handles are located immediately above the doors. The rear handles are equipped with hooks for dress hangers. Roof luggage rack — if equipped your vehicle may be equipped with a roof luggage rack for transporting accessories. Crossbars should always be used whenever cargo is pla...

  • Page 120

    Warning! Roof rack cargo must be securely tied down before driving your vehicle. Improperly secured loads may fall off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof luggage rack warnings and cau- tions when carrying cargo on your roof rack...

  • Page 121

    Getting to know your instrument panel contents 䡵 instrument cluster . . . . . . . . . . . . . . . .120 䡵 onboard diagnostic system (obd ii) . .121 ▫ onboard diagnostic system (obd ii) cybersecurity . . . . . . . . . . . . . . . . . . . . . . .122 䡵 instrument cluster display . . . . . . . . .123 ▫ i...

  • Page 122

    Instrument cluster 120 getting to know your instrument panel.

  • Page 123

    1. Speedometer • indicates the speed of the car. 2. Fuel level gauge • the fuel gauge in the instrument cluster display indicates the amount of fuel left in the tank. • the light comes on, together with a chime and the display of a message in the instrument cluster display, when the gas tank has 1.5...

  • Page 124

    If any of these systems require service, the obd ii system will turn on the “malfunction indicator light (mil).” it will also store diagnostic codes and other information to assist your service technician in making repairs. Although your vehicle will usually be drivable and not need towing, see your...

  • Page 125

    Instrument cluster display instrument cluster display description the vehicle can be equipped with an instrument cluster display which offers useful information to the driver. With the ignition in the stop/off position, opening/ closing of a door will activate the display for viewing, and display th...

  • Page 126

    Instrument cluster display control buttons the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and relea...

  • Page 127

    Engine oil change reset your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will flash in the instrument cluster display for approxi- mately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil...

  • Page 128

    • drive mode selector – auto mode – sport mode – traction/all weather mode • vehicle info – tire pressure – oil temperature – battery voltage • driver assist – lane departure warning • audio • navigation • messages • settings – display – units – clock & date – security – safety & assistance – lights...

  • Page 129

    • trip b – view and change trip b distance (miles or km). – view and change travel time b (hours/minutes/ seconds). – view and change average consumption b (mpg, or l/ 100km or km/l). – view and change average speed b (mph or km/h). Drive mode selector this instrument cluster display menu/submenu it...

  • Page 130

    • notice lanesense • by selecting this function, you can select the ⬙readi- ness ⬙ of lanesense, choosing between the options ⬙near,⬙ ⬙medium,⬙ or ⬙far.⬙ • intensity lanesense • using this function, you can select the force applied to the steering wheel to keep the car in the roadway through the ele...

  • Page 131

    • safety and assistance • lights • doors and locks refer to “uconnect settings” in “multimedia” for more information. Display by selecting ⬙display,⬙ you can access the following settings: • screen setup: allows you to configure the display screen. • language: allows you to select the language in wh...

  • Page 132

    Security by selecting the item “security,” you can make the following adjustments: • speed warning: set the vehicle speed limit (mph or km/h), which the driver is notified through a visual and acoustic signaling (display of a message and a symbol on the display). • seat belt buzzer: this function is...

  • Page 133

    • interior ambient lights: increase of decrease the brightness of the interior ambient lights. • greeting lights: enable/disable the vehicle’s greet- ing lights. • auto high beam: activate/deactivate the automatic main beam headlights — if equipped. • daytime lights: activate/deactivate the daytime ...

  • Page 134

    Warning and indicator lights the warning/indicator lights switch on in the instru- ment panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the inform...

  • Page 135

    Seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound....

  • Page 136

    The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a s...

  • Page 137

    Operation of the brake warning light can be checked by placing the ignition in the mar (acc/on/run) position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, ...

  • Page 138

    Coolant temperature warning light red telltale light what it means coolant temperature warning light this light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into...

  • Page 139

    Electric power steering fail warning light — if equipped red telltale light what it means electric power steering fail warning — if equipped this light is used to manage the electrical warning of the eps (electric power steering). Re- fer to “power steering” in “starting and operating” for further i...

  • Page 140

    Red telltale light what it means do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. Transmission fault warning light red telltale light what it means transmission fault warning ligh...

  • Page 141

    Vehicle security warning light — if equipped red telltale light what it means vehicle security warning light — if equipped this light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. Electronic...

  • Page 142

    Yellow telltale indicator lights low fuel indicator light yellow telltale light what it means low fuel indicator light when the fuel level reaches approximately 1.3–1.8 gal (5–7 l) this light will turn on, and remain on until fuel is added. Engine check/malfunction indicator light (mil) yellow tellt...

  • Page 143

    Yellow telltale light what it means when the engine is running, the mil may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be ser- viced as soon as possible if this occurs. Warning! A malfunctioning catalytic conv...

  • Page 144

    Wait to start light — if equipped yellow telltale light what it means wait to start light the “wait to start” telltale will illuminate for approximately two seconds when the ignition is turned to the run position. It’s duration may be longer based on colder operating condi- tions. Vehicle will not i...

  • Page 145

    Transmission temperature indicator light yellow telltale light what it means transmission temperature indicator light this light indicates that the transmission fluid temperature is running hot. This may occur with severe usage, such as trailer towing. If this light turns on, safely pull over and st...

  • Page 146

    Tire pressure monitoring system (tpms) warning light yellow telltale light what it means tire pressure monitoring system (tpms) warning light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss...

  • Page 147

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation ha...

  • Page 148

    Stop light failure indicator light yellow telltale light what it means stop light failure indicator light this light will illuminate if one or more of the stop light bulb fails. The failure relating to this light could be: • one or more blown bulbs • a blown protection fuse • a break in the electric...

  • Page 149

    Service stop/start system indicator light — if equipped yellow telltale light what it means service stop/start system indicator light — if equipped this telltale will turn on to indicate the stop/start system is not functioning properly and service is required. Anti-lock brake (abs) indicator light ...

  • Page 150

    Electric park brake fail light yellow telltale light what it means electric park brake fail warning light this telltale will turn on to indicate the electric park brake is not functioning properly and that service is required. Contact your authorized dealership. Exterior bulb failure indicator light...

  • Page 151

    Electronic stability control (esc) indicator light — if equipped yellow telltale light what it means electronic stability control (esc) indicator light the “esc indicator light” in the instrument cluster will come on when the ignition switch is turned to the avv/start position. If the “esc indicator...

  • Page 152

    Electronic stability control (esc) off indicator light yellow telltale light what it means electronic stability control (esc) off indicator light this light indicates the electronic stability control (esc) is off. Green telltale indicator lights turn signal indicator lights green telltale light what...

  • Page 153

    Park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. Front fog indicator light — if equipped green telltale light what it means front fog indicator light — if equipped t...

  • Page 154

    White telltale indicator lights cruise control on indicator light white telltale light what it means cruise control on indicator light this light will turn on when the cruise control has been enabled by the driver. Blue telltale indicator lights high beam indicator light blue telltale light what it ...

  • Page 155

    Safety contents 䡵 brake system . . . . . . . . . . . . . . . . . . . . . .154 䡵 electronic brake control system . . .154 ▫ electronic brake force distribution (ebd) . . .155 ▫ brake system warning light. . . . . . . . . . . . .155 ▫ anti-lock brake system (abs) . . . . . . . . . . .155 ▫ anti-lock b...

  • Page 156

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall brak- ing effectiveness. This will be evident by increased pedal travel dur...

  • Page 157

    Electronic brake force distribution (ebd) this function manages the distribution of the braking torque between the front and rear axles by limiting braking pressure to the rear axle. This is done to prevent overslip of the rear wheels to avoid vehicle instability, and to prevent the rear axle from e...

  • Page 158

    Warning! • the abs contains sophisticated electronic equip- ment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capa- bility. Installation of such equipment should be p...

  • Page 159

    Warning light” does not come on when the ignition switch is turned to the on position, have the light repaired as soon as possible. Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking s...

  • Page 160

    • driver door must be closed. • the vehicle must be on a sufficient grade. • the gear selection must match vehicle uphill direc- tion (i.E., vehicle facing uphill is in forward gear; vehicle backing uphill is in reverse gear). • hsa will work in reverse gear and all forward gears. The system will no...

  • Page 161

    4. Start the engine. 5. Rotate the steering wheel slightly more than one-half turn to the left. 6. Push the “esc off” button located in the lower switch bank below the climate control four times within twenty seconds. The “esc off indicator light” should turn on and turn off two times. 7. Rotate the...

  • Page 162

    • understeer - when the vehicle is turning less than appropriate for the steering wheel position. The “esc activation/malfunction indicator light” lo- cated in the instrument cluster will start to flash as soon as the esc system becomes active. The “esc activation/malfunction indicator light” also f...

  • Page 163

    Warning! (continued) inflated and unevenly worn tires may also de- grade esc performance. Any vehicle modifica- tion or poor vehicle maintenance that reduces the effectiveness of the esc system can increase the risk of loss of vehicle control, vehicle rollover, personal injury and death. Electronic ...

  • Page 164

    Maintain vehicle stability. The only notification the driver receives that the feature is active is the torque applied to the steering wheel. Note: the dst feature is only meant to help the driver realize the correct course of action through small torques on the steering wheel, which means the effec...

  • Page 165

    4. Never allow children to slide the shoulder belt behind them or under their arm. 5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front pa...

  • Page 166

    Enhanced seat belt use reminder system (beltalert) driver and passenger beltalert — if equipped beltalert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger seat beltalert) to buckle their seat belts. The belt alert feature is acti...

  • Page 167

    When the seat is folded flat (if equipped). It is recom- mended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. Beltalert can be activated or deactivated by your au- thorized dealer. Fca us llc does...

  • Page 168

    Warning! (continued) whether or not an air bag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could ...

  • Page 169

    Warning! (continued) shoulder so that your strongest bones will take the force in a collision. • a shoulder belt placed behind you will not pro- tect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder be...

  • Page 170

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 171

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 172

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 173

    Warning! • wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • position the shoulder b...

  • Page 174

    Seat belt pretensioner the front seat belt system is equipped with pretension- ing devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensio...

  • Page 175

    The alr. If the alr is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfort- ably wrap around the occupant’s mid-section. Slide the latch plate into the bu...

  • Page 176

    Warning! (continued) • do not use the automatic locking mode to re- strain occupants who are wearing the seat belt or children who are using booster seats. The locked mode is only used to install rear-facing or forward-facing child restraints that have a har- ness for restraining the child. Suppleme...

  • Page 177

    The orc contains a backup power supply system that may deploy the air bag system even if the battery loses power or it becomes disconnected prior to deployment. The orc turns on the air bag warning light in the instrument panel for approximately four to eight sec- onds for a self-check when the igni...

  • Page 178

    Redundant air bag warning light if a fault with the air bag warning light is detected, which could affect the supplemental re- straint system (srs), the redundant air bag warning light will illuminate on the instru- ment panel. The redundant air bag warning light will stay on until the fault is clea...

  • Page 179

    Warning! • being too close to the steering wheel or instru- ment panel during front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-facing ch...

  • Page 180

    Warning! (continued) may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • relying on the air bags alone could lead to more severe injuries in a co...

  • Page 181

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occupants for improved interaction with the front air bags. Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any accessories ...

  • Page 182

    When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not se...

  • Page 183

    Sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The sabics deploy downward, covering the side win- ...

  • Page 184

    Damage by itself is not a good indicator of whether or not side air bags should have deployed. Side air bags are a supplement to the seat belt restraint system. Side air bags deploy in less time than it takes to blink your eyes. Warning! • occupants, including children, who are up against or very cl...

  • Page 185

    Side impact deploys the left side air bags only and a right side impact deploys the right side air bags only. The side air bags will not deploy in all side collisions, including some collisions at certain angles, or some side collisions that do not impact the area of the passenger compartment. The s...

  • Page 186

    If a deployment occurs the front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the ...

  • Page 187

    Enhanced accident response system in the event of an impact, if the communication net- work remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response system perform the following functions: • cut off fuel...

  • Page 188

    Customer action customer will see note: each step must be held for at least two seconds 1. Turn ignition stop/ off/lock. (turn sig- nal must be placed in neutral state). 2. Turn ignition mar/ acc/on/run. Right turn light blinks. Left turn light is off. 3. Turn right turn signal switch on. Right turn...

  • Page 189

    If a reset procedure step is not completed within 60 seconds, then the turn signal lights will blink and the reset procedure must be performed again in order to be successful. Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you n...

  • Page 190

    • whether or not the driver and passenger safety belts were buckled/fastened; • how far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • how fast the vehicle was traveling. • these data can help provide a better understanding of the circumstances in which crashes and ...

  • Page 191

    There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in...

  • Page 192

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child re- straint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrie...

  • Page 193

    The infant carrier is only used rear-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rear-facing or forward-facing in the vehicle. Convertible child seats often have a highe...

  • Page 194

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 195

    4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using t...

  • Page 196

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 197

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint an- chorage system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 198

    Frequently asked questions about installing child restraints with latch what is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the c...

  • Page 199

    Frequently asked questions about installing child restraints with latch can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the ...

  • Page 200

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them ...

  • Page 201

    The end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center seat latch warning! • do not install a child restraint in the center position using the latch system. This position is not approved for installing child seats using the latch at...

  • Page 202

    5. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack in the straps according to the child restraint manufacturer’s instructions. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt pat...

  • Page 203

    Warning! • improper installation or failure to properly secure a child restraint can lead to failure of the restraint. The child could be badly injured or killed. • follow the child restraint manufacturer’s direc- tions exactly when installing an infant or child restraint. The seat belts in the pass...

  • Page 204

    Frequently asked questions about installing child restraints with seat belts what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a for- ward facing child restraint? Weight limit of the child restraint always use the tet...

  • Page 205

    1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make...

  • Page 206

    Installing child restraints using the top tether anchorage: warning! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that i...

  • Page 207

    4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child res...

  • Page 208

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • it is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be serious...

  • Page 209

    In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced...

  • Page 210

    Warning! An improperly attached, damaged, folded, or stacked floor mat, or damaged floor mat fasteners may cause your floor mat to interfere with the accelerator, brake, or clutch pedals and cause a loss of vehicle control. To prevent serious injury or death: • always securely attach your floor mat ...

  • Page 211

    Warning! (continued) • if the vehicle carpet has been removed and re- installed, always properly attach carpet to the floor and check the floor mat fasteners are secure to the vehicle carpet. Fully depress each pedal to check for interference with the accelerator, brake, or clutch pedals then re-ins...

  • Page 213

    Starting and operating contents 䡵 starting the engine . . . . . . . . . . . . . . .214 ▫ tip start feature . . . . . . . . . . . . . . . . . . . . .215 ▫ if engine fails to start . . . . . . . . . . . . . . . .215 ▫ cold weather operation . . . . . . . . . . . . . . .216 ▫ extended park starting. . ...

  • Page 214

    ▫ accelerating for passing . . . . . . . . . . . . . . .237 䡵 all wheel drive (awd) — if equipped .238 䡵 dynamic selector — if equipped . . . . .238 ▫ warning messages . . . . . . . . . . . . . . . . . . . .239 䡵 brake control — if equipped . . . . . . . .239 ▫ brake control . . . . . . . . . . . . ...

  • Page 215

    ▫ cng and lp fuel system modifications . . . .263 ▫ mmt in gasoline . . . . . . . . . . . . . . . . . . . .263 ▫ materials added to fuel . . . . . . . . . . . . . . .264 ▫ fuel system cautions. . . . . . . . . . . . . . . . . .264 ▫ carbon monoxide warnings . . . . . . . . . . . .265 䡵 adding fuel ....

  • Page 216

    Starting the engine before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allo...

  • Page 217

    4. If the engine does not start, place the ignition in the off mode and wait 10-15 seconds before attempting to restart the engine. Tip start feature do not press the accelerator. Cycle the ignition switch briefly to the start mode and release it. The starter motor will continue to run but will auto...

  • Page 218

    Caution! To prevent damage to the starter, do not continu- ously crank the engine for more than 25 seconds at a time. Wait 60 seconds before trying again. Cold weather operation to ensure reliable starting under extreme cold condi- tions an externally powered electric block heater (avail- able from ...

  • Page 219

    After starting — warming up the engine proceed as follows: • travel slowly, letting the engine run at a reduced rpm, without accelerating suddenly. • it is recommended to wait until the engine coolant temperature gauge starts to rise for maximum per- formance. Stopping the engine to shut off the eng...

  • Page 220

    While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving typ...

  • Page 221

    To apply the epb manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the epb engages. Once the parking brake is fully engaged, the brake warning lamp in the instrument cluster and an indica- tor on the switch will illuminate. If your f...

  • Page 222

    Note: • when parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the epb before placing the gear selector in park, otherwise the load on the transmission locking mechanism may make it difficult to move the g...

  • Page 223

    Long as engagement is desired. The brake warning lamp could illuminate in case of the hydraulic system is not available. The rear stop lamps will also be illuminated automatically while the vehicle remains in motion. To disengage the epb while the vehicle is in motion, release the switch. If the veh...

  • Page 224

    Safehold safehold is a safety feature of the epb system that will engage the park brake automatically if the vehicle is left unsecured while the ignition switch is in the run mode. For automatic transmissions, the epb will automatically engage if all of the following conditions are met: • vehicle sp...

  • Page 225

    Service mode has requirements that must be met in order to be activated: • the vehicle must be at a standstill. • the parking brake must be disabled. • the transmission must be in park or neutral. • the epb switch not activated. • the ignition is in the on mode. • the brake pedal not pressed. While ...

  • Page 226

    Caution! Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Note: during cold weather, you may experience in- creased effort in shifting until the transmission fluid...

  • Page 227

    Recommended vehicle shift speeds to utilize your manual transmission efficiently for fuel economy and performance, it should be upshifted as listed in the recommended shift speed chart. Shift at the vehicle speeds listed for acceleration. When heavily loaded or pulling a trailer, these recommended u...

  • Page 228

    Caution! (continued) speeds to cause engine and clutch damage are significantly lower. • failure to follow the maximum recommended downshifting speeds may cause the engine dam- age and/or damage the clutch, even if the clutch pedal is pressed. • descending a hill in low range with clutch pedal depre...

  • Page 229

    Reverse when the vehicle is stopped or moving at low speeds (refer to ⬙brake/transmission shift interlock system ⬙ in this section). Select the drive range for normal driving. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is no...

  • Page 230

    Caution! (continued) • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting into any gear, make sure your foot is firmly pressing the brake pedal. Note: you must press and hold the brake pedal while shifting out of park. Gear selector the tra...

  • Page 231

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. Do not race the engine when shifting from park or neutral into another gear range. Caution! After selecting any ...

  • Page 232

    When exiting the vehicle, always: • apply the parking brake. • shift the transmission into park. • turn the engine off. • remove the key fob. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when exiting the vehicle to guard against v...

  • Page 233

    Warning! (continued) warned not to touch the parking brake, brake pedal or the transmission gear selector. • do not leave the key fob in or near the vehicle (or in a location accessible to children), and do not leave the ignition in the acc or on/run mode. A child could operate power windows, other ...

  • Page 234

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Refer to “recreational towing” in “starting and operating” and “towing a disabled vehicle” in “in case of emergency” for further information. Drive (d) this r...

  • Page 235

    And improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driv- ing, trailer towing and many other situations. Operation when the gear selector is in the autostick position (beside the drive position),...

  • Page 236

    Autostick position at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Transmission limp home mode tra...

  • Page 237

    Ignition park interlock vehicles equipped with keyless enter-n-go: this vehicle is equipped with an ignition park inter- lock, which requires the transmission to be in park before the ignition can be turned to the stop/off mode. Also, the transmission is locked in park when- ever the ignition is in ...

  • Page 238

    Activation push the on/off button to activate the speed control. The cruise indicator light in the instrument cluster display will illuminate. To turn the system off, push the on/off button a second time. The cruise indicator light will turn off. The system should be turned off when not in use. Warn...

  • Page 239

    The driver’s preferred units can be selected through the uconnect system if equipped. Refer to ”uconnect set- tings” in “multimedia” for more information. The speed increment shown is dependant on the chosen speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set (+) button onc...

  • Page 240

    All wheel drive (awd) — if equipped this feature provides on-demand all-wheel drive (awd). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most of the traction. If the front wheels begin to lose traction, ...

  • Page 241

    Sport mode – this mode is designed to increase steering feedback to the driver with a slight increase in effort and changes the transmission shift schedules for more aggressive shifting. This driving mode is useful while driving on twisty roads where more steering precision is desired in spirited co...

  • Page 242

    Could lurch forward, once the brakes release a few seconds later. If the brake control event stops the vehicle completely, the system will hold the vehicle at standstill for two seconds and then release the brakes. If a brake control event begins at a speed below 20 mph (32 km/h), the system may pro...

  • Page 243

    Warning! Brake control is not intended to avoid a collision on its own, nor can brake control detect every type of potential collision. The driver has the responsi- bility to avoid a collision by controlling the vehicle via braking and steering. Failure to follow this warning could lead to serious i...

  • Page 244

    A more limited and gradual. This setting gives the driver the maximum possible time of reaction to pre- vent a possible accident. By changing the option to ⬙near⬙, the system will warn the driver of a possible accident with the vehicle ahead of it when the latter is a reduced distance. This setting ...

  • Page 245

    Recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path this warning may temporarily occur. If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruc...

  • Page 246

    Driving in the vicinity of a curve entering or exiting a large curve, the system could detect the presence of a vehicle that is in front of the car, but that does not preside in the same lane. In cases such as this, the system might respond. Small vehicles and/or not aligned to the lane the system i...

  • Page 247

    Lane changing of other vehicles vehicles that suddenly change lane, while standing in the traffic lane of their car and inside the field of action of the radar sensor may cause the intervention of the system. Passing of vehicles in an oncoming intersection the system could temporarily react to a veh...

  • Page 248

    General information this vehicle has systems that operate on radio fre- quency that comply with part 15 of the federal com- munications commission (fcc) rules and with indus- try canada standards rss- gen/210/220/310. Operation is subject to the following two conditions: 1. The device may not cause ...

  • Page 249

    Parksense sensors the four parksense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 inches (30 cm) up to 59 inches (150 cm) from the rear fascia/bumper in the horizonta...

  • Page 250

    Detection distances if the sensors detect more obstacles, it is taken into account only what is the shorter distance. Instrument cluster display parksense is displayed on the instrument cluster only if you have selected the item ⬙sound and display⬙ inside the ⬙settings⬙ menu of the uconnect system. ...

  • Page 251

    Parksense switch is pushed, and requires service, the parksense switch led will blink momentarily, and then the led will be on. Parksense will remember the previous state when the vehicle is switch off. Caution! After turning the ignition to stop, the parksense remains in this setting until the next...

  • Page 252

    • clean the rear parksense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The rear parksense system might not detect an obstacle behind the fasci...

  • Page 253

    Caution! (continued) above or below the sensors will not be detected when they are in close proximity. • the vehicle must be driven slowly when using parksense in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using p...

  • Page 254

    Turning lanesense on or off the default status of lanesense is “off”. The lanesense button is located on the end of the turn signal stalk, located on the left side of the steering column. To turn the lanesense system on, push the lanesense button once. A “lane sense on” message is shown in the instr...

  • Page 255

    Note: the lanesense system operates with the similar behavior for a right lane departure when only the right lane marking has been detected. Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings ...

  • Page 256

    • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The lanesense indi- cator changes from solid yellow to flashing yellow. At this time torque is applied t...

  • Page 257

    Note: • when enabled the system operates above 37 mph (60 km/h) and below 112 mph (180 km/h). • use of the turn signal suppresses the warnings. • the system will not apply torque to the steering wheel whenever a safety system engages. (anti-lock brakes, traction control system, electronic stability ...

  • Page 258

    A touchscreen button to disable the camera is available when the vehicle is not in reverse. Display of the camera image after shifting out of reverse can be disabled via uconnect settings. When enabled, active guide lines are overlaid on the image to illustrate the width of the vehicle and its proje...

  • Page 259

    Caution! • to avoid vehicle damage, parkview should only be used as a parking aid. The parkview camera is unable to view every obstacle or object in your drive path. • to avoid vehicle damage, the vehicle must be driven slowly when using parkview to be able to stop in time when an obstacle is seen. ...

  • Page 260

    May need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68° f (20° c) and the measure...

  • Page 261

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 262

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected, an audible chime will be activated and the “service tire pressure monitoring system” text message will display. If the ignition is cycled, this se...

  • Page 263

    Tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. General information the following regulatory statement applies to all radio frequency (rf) devices equipped in this vehicle: this device complies with part 15 of th...

  • Page 264

    2.4l engine all available gasoline engines are designed to meet all emissions regu- lations and provide excellent fuel economy and performance when us- ing high quality unleaded “regular” gasoline having a octane rating of 87 using the (r+m)/2 method. The use of premium gasoline is not recommended, ...

  • Page 265

    Caution! (continued) light” to illuminate. Please observe pump labels as they should clearly communicate if a fuel contains greater than 15% ethanol (e-15). Problems that result from using gasoline containing more than 15% ethanol (e-15) or gasoline containing methanol are not the responsibility of ...

  • Page 266

    Materials added to fuel besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion, and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle per- formance...

  • Page 267

    Note: intentional tampering with the emissions con- trol system can result in civil penalties being assessed against you. Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gase...

  • Page 268

    2. Insert the fuel nozzle in the filler pipe and proceed with filling the fuel tank. 3. Before removing the nozzle, wait at least 10 seconds to allow the fuel to flow inside of the tank. 4. Pull the nozzle from the filler pipe and then close the door. Emergency refueling procedure if the vehicle is ...

  • Page 269

    2. Open the fuel door. 3. Insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. 4. Remove the emergency fuel fill funnel, and close the door. 5. Store the emergency fuel fill funnel in the cargo area. Emergency fuel fill funnel — if equipped with full size spare...

  • Page 270

    Warning! • do not affix objects/plugs to the end of the filler neck other than is provided on the car. • the use of objects/plugs do not comply with the vehicle and may cause pressure increases inside the tank, creating dangerous conditions. • do not approach the neck of the tank with open flames or...

  • Page 271

    Components sometimes specified by purchasers for increased durability does not necessarily increase the vehicle’s gvwr. Tire size the tire size on the vehicle certification label repre- sents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size...

  • Page 272

    Caution! Do not load your vehicle any heavier than the gvwr or the maximum front and rear gawr. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Driving on slippery ...

  • Page 273

    3. Replace the tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. Driving through water driving through water more than a few inches/ centi...

  • Page 274

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 275

    If the “service power steering ⬙ or ⬙power steering assist off - service system” message and a steering wheel icon are displayed on the instrument cluster screen, it indi- cates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance....

  • Page 276

    Gross combination weight rating (gcwr) the gcwr is the total allowable weight of your vehicle and trailer when weighed in combination. Gross axle weight rating (gawr) the gawr is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure tha...

  • Page 277

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 278

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing con- dition. Trailer hitch classification definitions cl...

  • Page 279

    Trailer towing weights (maximum trailer weight ratings) the following chart provides the maximum trailer weight ratings towable for your given drivetrain. 1.4l turbo engine & 2.4 fwd trailer towing is not recommended. Engine max. Gtw (gross trailer wt.) max. Tongue wt. (see note) 2.4l awd 1,000 lbs ...

  • Page 280

    Consider the following items when computing the weight on the rear axle of the vehicle: • the tongue weight of the trailer. • the weight of any other type of cargo or equipment put in or on your vehicle. • the weight of the driver and all passengers. Note: remember that everything put into or on the...

  • Page 281

    Warning! (continued) in park. Always block or ⴖchockⴖ the trailer wheels. • gcwr must not be exceeded. • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitc...

  • Page 282

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 283

    Towing requirements — trailer lights and wiring (if equipped) whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four- and seven-pin wiring harness. Use a factory approved tra...

  • Page 284

    Four-pin connector 1 — female pins 2 — male pin 3 — ground 4 — park 5 — left stop/turn 6 — right stop/turn seven-pin connector 1 — battery 2 — backup lamps 3 — right stop/turn 4 — electric brakes 5 — ground 6 — left stop/turn 7 — running lamps 282 starting and operating.

  • Page 285

    Towing tips before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic transmission — if equipped select the drive range when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing...

  • Page 286

    Highway driving reduce speed. Air conditioning turn off temporarily. Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground front wheel drive (fwd) all-wheel drive (awd) flat tow none not allowed not allowed dolly tow rear not a...

  • Page 287

    Recreational towing front-wheel drive (fwd) models recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly (front wheels off the ground) or vehicle trailer (all four wheels off the ground). If using a tow dolly, follow this procedure: • ...

  • Page 288

    All-wheel drive (awd) models recreational towing (with all four wheels on the ground, or using a towing dolly) is not allowed. This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are off the ground. Caution! Towing this vehicle with any of its wheels on the ground can ...

  • Page 289

    In case of emergency contents 䡵 hazard warning flashers . . . . . . . . . .289 䡵 bulb replacement . . . . . . . . . . . . . . . . . .289 ▫ general information. . . . . . . . . . . . . . . . . . .289 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . .290 ▫ replacing exterior bulbs . . . . . . ....

  • Page 290

    䡵 towing a disabled vehicle . . . . . . . . . .334 ▫ front wheel drive (fwd) models . . . . . . . . .335 ▫ all wheel drive (awd) models . . . . . . . . . .335 䡵 tow eye usage — if equipped. . . . . . . . .336 ▫ front tow eye installation . . . . . . . . . . . . . .338 ▫ rear tow eye installation. . ...

  • Page 291

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncom- ing traffic of an emergency. Push the swit...

  • Page 292

    Replacement bulbs interior bulbs lamps bulb number front courtesy light c5w front courtesy lights (sun visors) c5w rear dome light (models without retractable roof) c5w rear interior lights (models with retractable roof) c5w interior lights w5w dome light (glove compartment) w5w exterior bulbs lamps...

  • Page 293

    Replacing exterior bulbs headlamps hi/lo beam light halogen to replace the bulbs proceed as follows: 1. Open the engine compartment and remove the head- lamp bulb cap. Front lamps 1 — headlamps 2 — daytime running lamps 3 — directional indicators 4 — fog lamps — if equipped headlamp bulb cap 8 in ca...

  • Page 294

    2. Rotate the headlamp bulb socket counterclockwise then pull outwards. 3. Release the locking tab on the headlamp bulb con- nector and remove the bulb and socket. 4. Install the new headlamp bulb making sure it is properly locked. Headlamp bulb socket headlamp bulb connector 292 in case of emergenc...

  • Page 295

    5. Install the headlamp bulb and socket; align the tabs and turn it clockwise making sure it is properly locked. Warning! Carry out the operation of replacing lamps only with the engine off. Also make sure that the engine is cold, to avoid the danger of burns. Position lights/daytime running lights/...

  • Page 296

    4. Rotate in a counterclockwise direction and remove the bulb and bulb socket. 5. To replace the bulb gently push bulb and rotate counterclockwise. 6. Insert the new bulb by pushing on it and turning it clockwise. Make sure the bulb is correctly locked in place. 7. Install the bulb and sockets and r...

  • Page 297

    Front fog lights to replace the bulbs proceed as follows: 1. Turn the front wheels completely. 2. Use a suitable tool to remove the access door. 3. By pushing the electrical connector tab remove the electrical connector. 4. Rotate the bulb counterclockwise, and then replace the bulb. 5. Insert the n...

  • Page 298

    Side indicators on external rear view mirrors – if equipped caution! The procedure is described as a guideline. For the replacement of the lamp it is recommended that you contact your authorized dealer. To replace the bulb proceed as follows: 1. Remove the mirror cap on the outside rear view mirror....

  • Page 299

    5. Insert the new bulb, making sure that it is locked into place 6. Reinstall the socket in to the transparent lens assem- bly. 7. Reinstall the cover on the outside rear view mirror, making sure it is locked into place. Rear tail lamps contain the following: • position lights • stop lights • direct...

  • Page 300

    3. Remove the rear tail lamp, sliding it toward the outside as shown. 4. Remove the screws and remove the rear tail lamp holder. 5. Replace the bulb as necessary. Tail lamp removal rear lamp assembly 1 — screws 298 in case of emergency.

  • Page 301

    6. Insert the new bulb, making sure it is properly locked. 7. Reassemble the lamp assembly on the rear tail lamp housing, tightening the screws. 8. Reposition the rear tail lamp on the vehicle. 9. Secure the rear tail lamp and reconnect the electrical connector. 10. Finally close the liftgate. 3th s...

  • Page 302

    2. Remove the bulbs from the individual side contacts. 3. Insert the new bulbs, and ensure that they are properly locked between the contacts. 4. Reinstall the license plate lens. Note: if removal the license plate lens using a suitable tool, be sure to cover the tip of the suitable with a cloth so ...

  • Page 303

    2. Release the retainer clips and bulb housing as shown. 3. Replace the bulbs by pulling straight out of bulb housing. 4. Insert the new bulbs, making sure that they are properly locked. 5. Reassemble the bulb housing and courtesy light housing making sure that they are properly locked. 6. Install t...

  • Page 304

    Dome light vanity mirror to replace the bulbs proceed as follows: 1. Lift the cover of the mirror and pull out the visor mirror light cover. 2. Replace the bulb, releasing it from the side contacts, and then insert the new bulb, making sure that it is properly locked between the contacts. 3. Reinsta...

  • Page 305

    Rear dome light — without retractable roof to replace the bulbs proceed as follows: 1. Using a suitable tool release the lamp assembly at both the ends. 2. Open the flap and replace the bulb. 3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Dome light to replace ...

  • Page 306

    2. Replace the bulb by removing it from the side contacts. 3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Interior cargo lights to replace the bulbs proceed as follows: 1. Open the luggage compartment and remove the dome light assembly. 2. Open the light cover ...

  • Page 307

    Warning! (continued) account the technical characteristics can cause malfunctions with the risk of fire. • halogen lamps contain gas under pressure, in the event of breakage be careful of the projection of fragments of glass. • halogen lamps must be handled by touching only the metallic part. If the...

  • Page 308

    Also please be aware that when using power outlets for extended periods of time with the engine off may result in vehicle battery discharge. Fuse removal to replace a fuse use the extractor attached to the fuse cover (located on the inside of the engine compartment fuse cover. Blade fuses 1 — electr...

  • Page 309

    Access to the fuses the fuses are grouped into four controllers located in the engine compartment, under the instrument panel and on the inside of the left side cargo trim panel. Engine compartment fuses/distribution unit the engine compartment fuse panel is located on the left side of the engine co...

  • Page 310

    Mounting fuse cover and locking screw proceed as follows: 1. Properly secure the fuse cover to the box, slide completely from top to bottom. 2. Fully depress the screw, using the special screw- driver supplied. 3. Slowly turn the screw clockwise. 4. Release the screw. Cavity maxi fuse cartage fuse m...

  • Page 311

    Cavity maxi fuse cartage fuse mini fuse description f03 – 20 amp blue – controller power supply body com- puter f04 – 30 amp pink – brake control elec- tronics module f05 70 amp tan – – electric power- assisted steering f06 20 amp yellow – – engine cooling fan f07 50 amp red – – engine cooling fan f...

  • Page 312

    Cavity maxi fuse cartage fuse mini fuse description f16 – – 5 amp tan engine control module power, au- tomatic transmis- sion f17 – – 10 amp red 15 amp blue supply primary loads (1.4l) supply primary loads (2.4l) f18 – – 30 amp green power all-wheel drive f19 – – 7.5 amp brown air conditioner compre...

  • Page 313

    Cavity maxi fuse cartage fuse mini fuse description f24 – – 15 amp blue electronic unit sup- ply automatic transmission f30 – – 30 amp green heated windshield – if equipped f83 – 40 amp green – air conditioning fan f84 – – 20 amp yellow power outlet (igni- tion powered) f87 – – 5 amp tan gear select...

  • Page 314

    Body computer fuse center the controller is located at the left side of the steering column at the bottom of the instrument panel. For the fuse replacement see your authorized dealer. Body controller fuse cavities 312 in case of emergency.

  • Page 315

    Cavity mini fuse description f31 7.5 amp brown fan air conditioning, power socket f33 20 amp yellow power window front (passenger side) f34 20 amp yellow power window front (driver’s side) f36 15 amp blue supply uconnect system, air conditioning, usb port, rear lateral ceiling light in case of open ...

  • Page 316

    Rear cargo fuse/relay distribution unit to access the fuses, remove the access door from the left rear panel of the rear cargo area. Push on the left side of the access door to unhinge and remove. Cavity mini fuse description f2 20 amp yellow audio system f3 20 amp yellow electric sunroof f5 30 amp ...

  • Page 317

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 318

    2. Lift the access cover using the load floor handle. 3. Remove the fastener securing the spare tire. Load floor handle spare tire fastener 316 in case of emergency.

  • Page 319

    4. Remove the jack, wheel bolt wrench, and wheel chocks. 5. Remove the spare tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire...

  • Page 320

    5. Turn the ignition to stop mode. 6. Chock both the front and rear of the wheel diago- nally opposite of the jacking posi- tion. For example, if changing the right front tire, chock the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking inst...

  • Page 321

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare tire, jack, and wheel bolt wrench. 2. If equipped with wheels where the center cap covers the wheel bolts, use the wheel bolt wrench to pr...

  • Page 322

    Jacking locations front jacking location front jacking engagement point rear jacking location 320 in case of emergency.

  • Page 323

    5. Raise the vehicle just enough to remove the flat tire. Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare...

  • Page 324

    Note: • your vehicle may be equipped with a compact spare tire or a limited — use spare tire. For further information refer to “tires — general information” in “maintaining your vehicle”. • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. 8. Insta...

  • Page 325

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the ...

  • Page 326

    Tire service kit — if equipped if a tire is punctured, you can make a first emergency repair using the tire service kit located in the rear storage compartment inside the storage container. Remove the tire service kit from the vehicle, take it out from the bag and place it near the punctured tire. S...

  • Page 327

    Warning! (continued) • a loose tire service kit thrown forward in a collision or hard stop could endanger the occu- pants of the vehicle. Always stow the tire service kit in the place provided. Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers,...

  • Page 328

    Warning! Tire service kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tire service kit. Do not exceed 65 mph (110 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you...

  • Page 329

    Jump starting if your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improp- erly so please follow the procedures in this section carefully. Note...

  • Page 330

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadver- tent electrical contact. You ...

  • Page 331

    Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 2. Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. 3. Connect the negative (-) end of the jumper cable to th...

  • Page 332

    Caution! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.E., cellular devices, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or pre...

  • Page 333

    Warning! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant b...

  • Page 334

    4. Push and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool down into the gear selector override access hole (at the right front corner of the gear selector assembly), and push and hold the override release lever down. 6. Move the gear selector to the neutral...

  • Page 335

    Note: push the ⬙esc off⬙ switch (if necessary), to place the electronic stability control (esc) system in ⬙partial off⬙ mode, before rocking the vehicle. Refer to “electronic brake control” in “safety” for further infor- mation. Once the vehicle has been freed, push the ⬙esc off ⬙ switch again to re...

  • Page 336

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condi- tion wheels off the ground fwd models all wheel drive flat tow none not allowed not allowed wheel lift or dolly tow rear not allowed not allowed front ok not all...

  • Page 337

    If you must use the accessories (wipers, defrosters, etc.) while being towed, the ignition must be in the run position. Note: the safehold feature will engage the electric park brake whenever the driver’s door is opened (if the ignition is run, transmission is not in park, and brake pedal is release...

  • Page 338

    Caution! • do not tow this vehicle with any of its wheels on the ground. Damage to the drivetrain will result. • front or rear wheel lifts must not be used. Inter- nal damage to the transmission or power transfer unit will occur if a front or rear wheel lift is used when towing. • towing this vehicl...

  • Page 339

    • do not use the tow eye to free a stuck vehicle. Refer to “freeing a stuck vehicle” in this section for further information. Warning! Stand clear of vehicles when pulling with tow eyes. • do not use a chain with a tow eye. Chains may break, causing serious injury or death. • do not use a tow strap ...

  • Page 340

    Caution! (continued) • in compliance with the above conditions, towing with a tow eye must take place with two vehicles (one towing, the other towed) aligned as much as possible along the same center line. Damage to your vehicle may occur if these guidelines are not followed. Front tow eye installat...

  • Page 341

    Rear tow eye installation the rear tow eye receptacle is located behind a access door on the rear bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle. Insert the wheel bolt wrench handle through the eye ...

  • Page 342

    Enhanced accident response system (ears) this vehicle is equipped with an enhanced accident response system. Please refer to “occupant restraint systems” in “safety” for further information on the enhanced acci- dent response system (ears) function. Event data recorder (edr) this vehicle is equipped...

  • Page 343

    Maintaining and caring for your vehicle contents 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . .343 䡵 replacement parts . . . . . . . . . . . . . . . . .344 䡵 dealer service . . . . . . . . . . . . . . . . . . . .344 䡵 maintenance schedule . . . . . ...

  • Page 344

    ▫ tire terminology and definitions . . . . . . . . .384 ▫ tire loading and tire pressure . . . . . . . . . .384 䡵 tires — general information . . . . . . .389 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . .389 ▫ tire inflation pressures . . . . . . . . . . . . . . . .390 ▫ tire pressur...

  • Page 345

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control sys- tem. Failure to pass could prevent vehicle registration. For states that require an inspection and main- tenance (i/m), this check verifies t...

  • Page 346

    Obd ii system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle’s obd ii system is ready or not, if the mil is illuminated during normal vehicle operation you should have your vehicle ser- viced before going to the i/m...

  • Page 347

    Operating conditions can cause the change oil message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). Your authorized dealer will reset the oil change indica- tor message after completing the sched...

  • Page 348

    Once a month or before a long trip: • check engine oil level. • check windshield washer fluid level. • check the tire inflation pressures and look for un- usual wear or damage. • check the fluid levels of the coolant reservoir, and brake master cylinder reservoir, and fill as needed. • check functio...

  • Page 349

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,0...

  • Page 350

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,0...

  • Page 351

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,0...

  • Page 352

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,0...

  • Page 353

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 16,000 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,0...

  • Page 354

    ** the spark plug change is distance based only, yearly intervals do not apply. The following are essential to ensure correct operation and prevent serious damage to the engine: • only use spark plugs of the same make and type which are specially certified for such engines (refer to “fluids, lubrica...

  • Page 355

    Engine compartment — 1.4l turbo engine 1 — air cleaner filter 4 — brake fluid reservoir 7 — washer fluid reservoir 2 — engine oil dipstick 5 — battery 8 — coolant pressure bottle cap 3 — oil fill cap 6 — power distribution center (fuses) 9 — coolant pressure bottle 9 maintaining and caring for your ...

  • Page 356

    Engine compartment — 2.4l engine maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require ser...

  • Page 357

    Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized dealer or qualified repai...

  • Page 358

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled mainte- nance. Refer to the “maintenance schedule” for further information. Note: under no circumstances should oil change intervals exceed 10,000 miles (16,000 km), twelve months ...

  • Page 359

    Dyes) to the engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. Disposing of used engine oil and oil filters care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately ...

  • Page 360

    Maintenance-free battery your vehicle is equipped with a maintenance-free bat- tery. You will never have to add water, nor is periodic maintenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 361

    Include cleaning of the condenser fins and a perfor- mance test. Drive belt tension should also be checked at this time. Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can expl...

  • Page 362

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as mopar spray white lube to assure quiet, easy ...

  • Page 363

    To enable the service position strategy, the wipers must be in the park position before placing the ignition in the off mode. Service mode must be activated within two minutes after the ignition is placed in the off mode. To have a correct activation of strategy, the service position command (antipa...

  • Page 364

    4. Install the wiper blade and firmly push the wiper blade until it snaps into place. Rear wiper blade removal/installation 1. Carefully lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab and hold the wiper arm closest to the wiper blade end while pushing the ...

  • Page 365

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breath- ing co, refer to “safety tips/exhaust gas” in the “safety” section for further information. • a hot e...

  • Page 366

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 367

    Flushed and refilled with fresh engine coolant (anti- freeze). Check the front of the a/c condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Cooling system — drain, flush and refill note: some ve...

  • Page 368

    Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conforming to ms.90032) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to ten years or 150,000 miles (240,000 km) before replacement. To pre- vent reducing this extend...

  • Page 369

    If hoat and oat coolant are mixed in an emer- gency, have a authorized dealer drain, flush, and refill with oat coolant (conforming to ms.90032) as soon as possible. Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze) and to ensure that engine c...

  • Page 370

    As long as the engine operating temperature is satisfac- tory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicl...

  • Page 371

    Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnor- mally high brake temperatures, excessive lining wear, and possible brake damage. Riding the brakes may also reduce braking capacity in an em...

  • Page 372

    Warning! (continued) original factory installed hydraulic master cylin- der reservoir. • to avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in ...

  • Page 373

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubricant has become contaminated with water. Note: if contaminated with water, the fluid should be c...

  • Page 374

    Fluid level check the fluid level is preset at the factory and does not require adjustment under normal operating conditions. Routine fluid level checks are not required, therefore the transmission has no dipstick. Your authorized dealer can check your transmission fluid level using special service ...

  • Page 375

    What causes corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • road salt, dirt and moisture accumulation. • stone and gravel impact. • insects, tree sap and tar. • salt in the air near seacoast localities. ...

  • Page 376

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 377

    Prevent damage to the wheels. Mopar wheel treatment or mopar chrome cleaner or their equivalent is recom- mended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels. Do not use any products on dark vapor or black satin chrome wheels. They will permanently damage this finish an...

  • Page 378

    • for grease stains, apply mopar multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • do not use any harsh solvents or any other form of protectants on stain repel products. Interior care use mopar total clean to clean fabric upholstery and...

  • Page 379

    Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses ...

  • Page 380

    Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft cloth. A mild soap solution may be used, but do not use high alcohol c...

  • Page 381

    Raising the vehicle in the case where it is necessary to raise the vehicle, go to an authorized dealer or service station. The vehicle lifting points on the vehicle are marked on side skirts with symbols ( see example shown). Lifting point locations 9 maintaining and caring for your vehicle 379.

  • Page 382

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 383

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Ex- ample: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it b...

  • Page 384

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 385

    Tire identification number (tin) the tin may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 386

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 387

    Warning! • overloading of your tires is dangerous. Overload- ing can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. • improperly inflated tires are dangerous and can cause collisions....

  • Page 388

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 389

    Steps for determining correct load limit— (1) locate the statement “the combined weight of occupants and cargo should never exceed xxx kg or xxx lbs.” on your vehicle’s placard. (2) determine the combined weight of the driver and passengers that will be riding in your vehicle. (3) subtract the combi...

  • Page 390

    Warning! Overloading of your tires is dangerous. Overload- ing can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 388 maintaining and caring for your vehicle.

  • Page 391

    Tires — general information tire pressure proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Four primary areas are affected by improper tire pressure: • safety and vehicle stability • economy • tread wear • ride comfort safety warning! • improperly i...

  • Page 392

    Fuel economy underinflated tires will increase tire rolling resistance resulting in higher fuel consumption. Tread wear improper cold tire inflation pressures can cause abnor- mal wear patterns and reduced tread life, resulting in the need for earlier tire replacement. Ride comfort and vehicle stabi...

  • Page 393

    Example: if garage temperature = 68°f (20°c) and the outside temperature = 32°f (0°c) then the cold tire inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to...

  • Page 394

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 395

    Snow tires some areas of the country require the use of snow tires during the winter. Snow tires can be identified by a “mountain/snowflake” symbol on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of f...

  • Page 396

    Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact or limited use temporary spare installed. Damage to the vehicle may result. Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above ...

  • Page 397

    Tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure – improper cold tir...

  • Page 398

    See the tire sizing chart example found in the “tire safety information” section of this manual for more information relating to the load index and speed symbol of a tire. It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your ...

  • Page 399

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on front tires only. • only 215...

  • Page 400

    Department of transportation uniform tire quality grades the following tire grading categories were estab- lished by the national highway traffic safety ad- ministration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehi...

  • Page 401

    Tires must meet under the federal motor vehicle safety standard no. 109. Grades b and a represent higher levels of performance on the laboratory test wheel, than the minimum required by law. Warning! The temperature grade for this tire is established for a tire that is properly inflated and not over...

  • Page 402

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the power transfer unit. Tire rotation schedule should be followed to balance tire wear. Storing the vehicle if the vehicle s...

  • Page 403

    Across dirty surfaces. Do not use plastic sheeting which will not allow the evaporation of moisture present on the surface of the vehicle. • inflate the tires at a pressure of +7.25 psi (+0.5 bar) higher than recommended on the tire placard and check it periodically. • do not drain the engine coolin...

  • Page 405

    Technical data contents 䡵 vehicle identification number . . . . . .404 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . .404 ▫ torque specifications . . . . . . . . . . . . . . . . . .405 䡵 fluid capacities . . . . . . . . . . . . . . . . . . .407 䡵 fluids, lubricants, ...

  • Page 406

    Vehicle identification number the chassis number (vin) and stamped on the plate illustrated in, located on the left front corner of the instrument panel cover, visible from the outside vehicle through the windshield. This number is also stamped on the floor of the passen- ger compartment, in front o...

  • Page 407

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 89 ft-lbs (120 n·m) m12 x 1.25 x 25.5 17 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. Inspect the wheel mounting surface prior to mountin...

  • Page 408

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 409

    Fluid capacities u.S metric fuel (approximate) 1.4l turbo/2.4l engine 12.7 gallons 48 liters engine oil with filter 1.4l turbo engine (sae 5w-40 synthetic, api certified) 4.0 quarts 3.8 liters 2.4l engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters cooling system * 1.4l turbo engine (mopar anti...

  • Page 410

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material stan- dard ms.90032. Engine oil...

  • Page 411

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar c series manual & dual dry clutch transmission fluid. Automatic transmission – if equipped use only mopar zf 8&9 speed atf automatic trans- mission fluid, or equivalent. Failure to use th...

  • Page 413

    Multimedia contents 䡵 cybersecurity. . . . . . . . . . . . . . . . . . . . . .412 䡵 uconnect settings . . . . . . . . . . . . . . . . .413 ▫ buttons on the faceplate. . . . . . . . . . . . . . .415 ▫ buttons on the touchscreen. . . . . . . . . . . . .415 ▫ customer programmable features — uconnect 5...

  • Page 414

    Cybersecurity your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive information. This information allows systems and fea- tures in your vehicle to function properly. Your vehicle may be equipped with c...

  • Page 415

    Note: • fca or your dealer may contact you directly regard- ing software updates. • to help further improve vehicle security and mini- mize the potential risk of a security breach, vehicle owners should: • routinely check www.Driveuconnect.Com/ software-update to learn about available uconnect softw...

  • Page 416

    Uconnect 5.0 buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate uconnect 6.5 nav buttons on the touchscreen and buttons on the faceplate 1 — uconnect buttons on the touchscreen 2 — uconnect buttons on the faceplate 41...

  • Page 417

    Buttons on the faceplate buttons on the faceplate are located below, and beside the uconnect system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90)...

  • Page 418

    Display after pressing the “display” button on the touchscreen, the following settings will be available: setting name selectable options display mode auto manual brightness + – language english español français touchscreen beep units after pressing the “units” button on the touchscreen, you may sel...

  • Page 419

    After pressing the “custom” button with “units” on the touchscreen, you may select from the following menu items: setting name selectable options distance mi km fuel consumption mpg (us) mpg (uk) l/100 km km/l pressure psi kpa bar temperature °c °f voice after pressing the “voice” button on the touc...

  • Page 420

    Clock & date after pressing the “clock & date” button on the touch- screen, the following settings will be available: setting name selectable options set time & format 12 hour 24 hour note: press the corresponding arrow above and below the current time to adjust, then select “am” or “pm.” show time ...

  • Page 421

    Safety/assistance after pressing the “safety/assistance” button on the touchscreen, the following settings will be available: setting name selectable options parkview backup cam- era delay — if equipped note: when the vehicle is shifted out of reverse (with camera delay turned off), the rear camera ...

  • Page 422

    Setting name selectable options note: when this feature is enabled, fixed (static) grid lines are overlaid on the rear backup camera image to illustrate the width of the vehicle. Forward collision warning-plus (fcw+) — if equipped near far note: the front collision warning (fcw+) feature can be set ...

  • Page 423

    Setting name selectable options front parksense volume — if equipped low medium high rear parksense volume — if equipped low medium high rear parksense braking assist — if equipped note: when this feature is selected, the park assist system will detect objects located behind the vehicle and utilize ...

  • Page 424

    Setting name selectable options blind spot alert — if equipped off lights lights & chime note: • when this feature is selected, the blind spot alert feature can be set to off, lights or lights and chime. The blind spot alert feature can be activated in lights mode. When this mode is selected, the bl...

  • Page 425

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available: setting name selectable options headlight sensitiv- ity 1 2 3 note: the greater the sensitivity set, the less the external light variation required to turn on the lights (e.G. With a set- ting on ...

  • Page 426

    Setting name selectable options cornering lights on off flash lights with lock — if equipped on off doors & locks after pressing the “doors & locks” button on the touchscreen, the following settings will be available: setting name selectable options auto door locks on off note: when this feature is ...

  • Page 427

    Setting name selectable options passive entry on off remote door unlock/ door unlock driver all note: when “driver” is selected, only the driver’s door will unlock on the first push of the key fob unlock button, you must push the key fob unlock button twice to unlock the passenger’s doors. When “all...

  • Page 428

    Audio after pressing the “audio” button on the touchscreen, the following settings will be available: setting name selectable options equalizer + – note: bass/mid/treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. Balance/f...

  • Page 429

    Phone/bluetooth after pressing the “phone/bluetooth” button on the touchscreen, the following settings will be available: setting name selectable options paired phones this feature shows which phones are paired to the phone/bluetooth sys- tem. For further information, refer to the uconnect owner’s m...

  • Page 430

    Setting name selectable options channel skip channel skip note: siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning. To make your selection, press the “channel skip” button on the touchscreen, select t...

  • Page 431

    Restore settings after pressing the “restore settings” button on the touchscreen, the following settings will be available: setting name selectable options restore settings ok cancel x note: when this feature is selected, it will reset all settings to their default settings. To restore the settings ...

  • Page 432

    Customer programmable features — uconnect 6.5 nav settings press the settings button to display the menu setting screen. In this mode the uconnect system allows you to access programmable features that may be equipped such as display, clock, safety & driving assistance, lights, doors & locks, engine...

  • Page 433

    Display after pressing the “display” button on the touchscreen, the following settings will be available: setting name selectable options display mode auto manual note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the displ...

  • Page 434

    Units after pressing the “units” button on the touchscreen, you may select each unit of measure independently displayed in the instrument cluster display. The follow- ing selectable units of measure are listed below: setting name selectable options us metric note: when us is selected, distance is se...

  • Page 435

    Voice after pressing the “voice” button on the touchscreen, the following settings will be available: setting name selectable options voice response length brief detailed show command list always with help never clock after pressing the “clock” button on the touchscreen, the following settings will ...

  • Page 436

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen, the following settings will be avail- able: setting name selectable options forward collision warning-plus (fcw+) — if equipped near medium far note: the front collision warning (fcw+) feature can...

  • Page 437

    Setting name selectable options lanesense warning — if equipped early med late note: when this feature is selected, it sets the distance at which the steering wheel will provide feedback for potential lane departures. Lanesense strength — if equipped low medium high note: when this feature is select...

  • Page 438

    Setting name selectable options note: • when this feature is selected, the blind spot alert feature can be set to off, lights or lights and chime. The blind spot alert feature can be activated in lights mode. When this mode is selected, the blind spot monitor (bsm) system is activated and will only ...

  • Page 439

    Setting name selectable options parkview backup cam- era delay on off note: when the vehicle is shifted out of reverse (with camera delay turned off), the rear camera mode is exited and the navigation or audio screen appears again. When the vehicle is shifted out of reverse (with camera delay turned...

  • Page 440

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available. Setting name selectable options headlight sensitiv- ity 1 2 3 note: the greater the sensitivity set, the less the external light variation required to turn on the lights (e.G. With a set- ting on ...

  • Page 441

    Setting name selectable options flash lights with lock — if equipped on off headlights with wipers — if equipped on off doors & locks after pressing the “doors & locks” button on the touchscreen, the following settings will be available: setting name selectable options auto door lock yes no note: wh...

  • Page 442

    Setting name selectable options remote door unlock all driver note: this feature will allow you to program your remote door locks to open “all” or only the “driver” with the first push of the key fob or grabbing the passive entry door handle. Passive entry on off note: this feature allows you to loc...

  • Page 443

    Engine off options after pressing the “engine off options” button on the touchscreen, the following settings will be available: setting name selectable options radio off delay 0 min 20 min headlight off delay — if equipped + – note: when this feature is selected, the driver can choose to have the he...

  • Page 444

    Setting name selectable options speed adjusted volume 1 2 3 surround sound — if equipped on off loudness — if equipped yes no aux volume off- set — if equipped on off auto-on radio on off recall last note: the radio automatically turns on when vehicle is in run or will recall whether it was on or of...

  • Page 445

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touchscreen, the following settings will be available: setting name selectable options sxm tune start note: the “tune start” feature begins playing the current song from the beginning when you tune to a music channel usin...

  • Page 446

    Setting name selectable options subscription information subscription info note: new vehicle purchasers or lessees will receive a free limited time subscription to siriusxm satellite radio with your radio. Following the expiration of the free services, it will be necessary to access the information ...

  • Page 447

    Clear personal data after pressing the “clear personal data settings” but- ton on the touchscreen, the following settings will be available: setting name selectable options clear personal data yes no note: when this feature is selected, it will remove personal data including bluetooth devices and pr...

  • Page 448

    Located below the heating ventilation and air condi- tioning controls is the front usb port and aux jack. Refer to the uconnect owner’s manual supplement for external usb support capability. Center console usb port located in the center console is a second usb port. Note: depending on vehicle config...

  • Page 449

    Aux/media player, etc.) and can also be used to select/enter an item while scrolling through menu. The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-ha...

  • Page 450

    The internal wireless radio operates within guidelines found in radio frequency safety standards and recom- mendations, which reflect the consensus of the scientific community. The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is fa...

  • Page 451

    Voice recognition quick tips introducing uconnect start using uconnect voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect 5.0 or 6.5 nav system. Key features: • five-inch color touchscreen display with am/fm/ usb/blu...

  • Page 452

    Get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pair- ing instructions. 2. Reduce background noise. Wind and passenger con- versations are ex...

  • Page 453

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Noti...

  • Page 454

    Tip: at any time, if you are not sure of what to say or want to learn a voice command, press the vr button and say “help.” the system will provide you with a list of commands. Media uconnect offers connections via usb port, bluetooth and auxiliary ports (if equipped). Voice operation is only availab...

  • Page 455

    • play artist beethoven; play album greatest hits; play song moonlight sonata; play genre classical. Tip: press the browse button on the touchscreen to see all of the music on your ipod or usb device. Your voice command must match exactly how the artist, album, song and genre information is displaye...

  • Page 456

    • call back (call previous incoming phone number). Tip: when providing a voice command, push the phone button and say “call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “call john smith work.” voice text reply uconnect wil...

  • Page 457

    Pre-defined voice text reply responses yes. Stuck in traffic. See you later. No. Start without me. I’ll be late. Okay. Where are you? I will be minutes late. Call me. Are you there yet? I’ll call you later. I need directions. See you in of minutes. I’m on my way. Can’t talk right now. I’m lost. Than...

  • Page 458

    Siri eyes free — if equipped siri lets you use your voice to send text messages, select media, place phone calls and much more. Siri uses your natural language to understand what you mean and will respond back to confirm your requests. The system is designed to keep your eyes on the road and your ha...

  • Page 459

    Note: a push and release of the button will start normal embedded vr functions. The push and hold, then release of the button will start siri functions. 2. After the double beep, begin speaking to siri. Examples of siri commands and questions: • ⬙play rolling stones⬙ • ⬙send text message to john⬙ • ...

  • Page 460

    General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause...

  • Page 461

    Index 12.

  • Page 462

    About your brakes . . . . . . . . . . . . . . . . . . . . . . .154 adding engine coolant (antifreeze) . . . . . . . . . . .366 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 adding washer fluid . . . . . . . . . . . . . . . . . . . . .362 additives, fuel . . . . . . . . . . ....

  • Page 463

    Axle lubrication . . . . . . . . . . . . . . . . . . . . . . . . .409 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . .135, 358 charging system light . . . . . . . . . . . . . . . . . .135 belts, seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207 blind spot monitoring ....

  • Page 464

    Clutch fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . .369 coin holder . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 cold weather operation . . . . . . . . . . . . . . . . . . .216 connector uci . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 universal co...

  • Page 465

    Electronic roll mitigation . . . . . . . . . . . . . . . .161 traction control system . . . . . . . . . . . . . . . . .159 electronic speed control (cruise control) . . . . . . .235 electronic throttle control warning light . . . . . . .139 emergency, in case of hazard warning flasher . . . . . . . ...

  • Page 466

    Fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 fluids, lubricants and genuine parts . . . . . . . . . .408 fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 forward collision warning . . . . . . . . . . . . . . . . .239 freeing a stuck vehicle . . . . ....

  • Page 467

    Holder, coin. . . . . . . . . . . . . . . . . . . . . . . . . . . .115 holder, cup . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 hood prop . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 hood release . . . . . . . . . . . . . . . . . . . . . . . . . . .104 ignition key . . ...

  • Page 468

    Light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 air bag . . . . . . . . . . . . . . . . . . . . . . . . . .132, 207 automatic headlights . . . . . . . . . . . . . . . . . . . .67 brake warning . . . . . ...

  • Page 469

    Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 vanity . . . . . ....

  • Page 470

    Radio operation . . . . . . . . . . . . . . . . . . . . . . . . .447 rain sensitive wiper system . . . . . . . . . . . . . . . . .76 rear camera . . . . . . . . . . . . . . . . . . . . . . . . . . .255 rear cross path . . . . . . . . . . . . . . . . . . . . . . . . . .64 rear parksense system . . . ...

  • Page 471

    Seat belt maintenance . . . . . . . . . . . . . . . . . . . . .378 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .164 seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . .163, 207 adjustable shoulder belt . . . . . . . . . . . . . . . . .169 adjustable upper shoulder ancho...

  • Page 472

    Steering wheel audio controls . . . . . . . . . . . . . .446 steering wheel mounted sound system controls . .446 storage, vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .96 stuck, freeing. . . . . . . . . . . . . . . . . . . . . . . . . . .332 sun roof . . . . . . . . . . . . . . . . . . ...

  • Page 473

    Traction control . . . . . . . . . . . . . . . . . . . . . . . . .159 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . .273 cooling system tips . . . . . . . . . . . . . . . . . . . .283 hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 minimum requirements . . . ....

  • Page 474

    Wind buffeting. . . . . . . . . . . . . . . . . . . . . . .100, 102 window fogging . . . . . . . . . . . . . . . . . . . . . . . . .96 windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 windshield defroster. . . . . . . . . . . . . . . . . . . . . .207 windshield wiper blades. ....

  • Page 475

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 476

    O w n e r ’ s m a n u a l 2 0 1 7 2017 fia t ® 500x fiat ® 500x first edition printed in u.S.A. ©2016 fca us llc. All rights reserved. Fiat is a registered trademark of fca group marketing s.P.A., used under license by fca us llc. 17fb-126-ab second edition.