1. DL manuals
  2. Foxun
  3. Wireless Router
  4. SX-MX88-3DCAT
  5. Quick Start Manual

Foxun SX-MX88-3DCAT Quick Start Manual

Manual is about: HDMI Matrix 8x8 built-in WiFi

Summary of SX-MX88-3DCAT

  • Page 1

    Quick start guide features •any eight sources to any eight displays,each port supports hdmi or dvi inputs. •transmission distance up to 50m under 1080p@60hz over single cat5e or cat6 cable. •transmission distance up to 30m under 1080p@60hz over double cat5e or cat6 cable. •the hdmi input is compensa...

  • Page 2

    Packing contents 1) main unit: 8x8 hdmi matrix 2) power supply dc 12v 4a 3) remote controller 4) ir-rx cable x 1pcs 5) m3x5 screw x 8pcs 6) operating instructions 7) mounting ear 8) rs232 cable dimensional drawing table of contents package contents dimensional drawing specifications panel descriptio...

  • Page 3

    -5 to +35 c(+23 to +95 5 to 90%rh (no condensation) 110-240v/ 12vdc power supply 24watts cold-rolled (cold rolled) steel w436.5xh280xt42.5mm 3800g 1080p 30m over dual cat5e/6 cable 1080p 50m over single cat5e/6 cable hdmi receptacle. Power connector terminal power dc receptacle ir extender rj45 rece...

  • Page 4

    Rear panel all: press this button to set all the outputs to display with the same input. Frist pressing the “all”button then press an input number to confirm the selection. D/s: press this button to double lan cable mode and press it again to single lan cable mode. Wifi: this slot is used to install ...

  • Page 5

    1. Front panel control the hdmi matrix front panel control switching inputs to the various outputs. There are four groups of leds for each output port. The led lit on the position means that the output port selects this input as its source. 3. Ir extender control user can use the ir receiver cable t...

  • Page 6

    2.1 receive window the “receive window” will show the message received from matrix. When you click the control buttons (see step 4) or send control command (see 2.3) to matrix, it will send out the message about “operation results” as right: 2.2 status button click this button to read the status of ...

  • Page 7

    4 setting button click this button to enter setting menu. If the signal is not stable, please turn on the hdmi long cable mode. 4.1 edid set button select the output port in “port select” column, click “read edid” button to get edid from display equipment. Select the input port in “port select” colu...

  • Page 8

    5.Android os control 5.1 install android apk(matrix88.Apk) 5.2 connect device set the wifi in your phone/ pad, run “matrix 88” , input equipment wifi module’s ip address (10.10.100.254), then click “connect” to enter. Main menu 8.

  • Page 9

    6.Ios control 6.1 go to “app store ” ， search “matrix88” ,download and install the app. 6.2 connect device set the wifi in your iphone/ipad ,run “matrix88”, input equipment wifi module’s ip address (10.10.100.254) ,then click “button” to enter. Main menu 9.

  • Page 10

    Rs-232 pin assignment hdmi matrix pin assignment 1 nc 2 tx 3 rx 4 nc 5 gnd 6 nc 7 nc 8 nc 9 nc remote control console pin assignment 1 nc 2 rx 3 tx 4 nc 5 gnd 6 nc 7 nc 8 nc 9 nc 10

  • Page 11

    11 tv1 rx tv2 tv3 tv4 tv5 tv6 tv7 tv8 blue-ray player ps3 xbox stb dvd pc hd camera iptv hdmi matrix hdmi cable dual cat5e/6 cable rx rx rx rx rx rx rx.

  • Page 12

    Rs-232 commands command cir_0x\r hex 63 69 72 20 30 xx 0d 0a description feedback s1y output 1 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8. Cir_1x\r 63 69 72 20 31 xx 0d 0a s2y output 2 select input 1~8 “x” : indicate the input po...

  • Page 13

    13.

  • Page 14

    14.