Franklin Electric IPS Installation & Operation Manual
Operation
• Ensure that all connections are properly torqued and enclosure is closed
prior to applying power to the device.
• Ensure all mechanical equipment operated by the starter is clear for safe
operation in case of starter activation.
• When in AUTO mode, starter may be activated remotely by the
control system.
Operation Modes
ON (HAND)
Press the ON mode button to manually engage motor.
OFF (RESET)
Pressing the OFF mode button manually disengages the motor.
Additionally, the OFF button serves as a manual Reset. Press and
hold OFF for 5 seconds to Reset the starter after a fault trip.
AUTO
When utilizing AUTO mode, the starter is controlled by a remote
Start/Stop command.
LED Status Indicators
MODE LEDs
Illuminates with corresponding mode selection (HAND/OFF/AUTO).
Flashing mode LED signals a fault trip during the last operating
Fireman’s Override operation.
RUN LED
Illuminates when starter is given a Run signal and proof of power is
power to the motor.
FAULT LED
Illuminates upon a fault condition or overload trip. Starter must be
returned to the OFF mode in order to Reset. A 180 second minimum
cool down period must elapse prior to further operation.
Product improvement is a continual process. Franklin Electric, Mira,
Orion and associated logos are trademarks of Franklin Electric.
All sales subject to Franklin Electric Terms & Conditions.
Precautions
To prevent injury and property damage, follow these instructions.
Failure to adhere to installation/operation procedures and all
applicable codes may result in hazards as indicated by warning
codes outlined below:
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury. This signal word is to be limited to the
most extreme situations.
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against
unsafe practices.
This is the safety alert symbol. Read and follow instructions carefully to
avoid a dangerous situation.
This symbol alerts the user to the presence of “dangerous voltage”
inside the product that might cause harm or electrical shock.
DANGER
WARNING
CAUTION
Safety Instructions
Equipment can start automatically. Lockout/tagout before servicing.
expert personnel should perform maintenance and installation. Contact the
nearest authorized service facility for examination, repair, or adjustment.
Do not disassemble or repair unit unless described in this manual; death
manual data subject to change. Consult factory for additional information.
DANGER
CAUTION
ESC
FLA
RESET
CLASS
5 5
.
1 0
M
S T P 0 0
. A
ESC
Lockout Settings & Overload Adjustment
any of the protective functions of the IPS starter, the settings must
Default Display Screen
Press and hold the UP and DOWN buttons for
2 seconds until the display screen matches the
display at left.
Press the ENTER button to change the menu
from “LOCKED” to “UNLOCKED.”
The lockout feature is now disabled. Press the
ESC key to return to the Default
Display screen.
Adjustments may now be made to the Overload FLA setting and
Ground Fault Level setting. The lockout feature will automatically
re-enable itself after 2 minutes.
Overload Adjustment (Setting Range1.0 - 95.0 Amps)
Once settings are unlocked, follow the steps
below to adjust overload setting.
Press the DOWN arrow once.
Edit FLA Screen
Press ENTER
Use the UP and DOWN keys to make
adjustments.
Press ENTER to save setting.
Press ESC to return to the Default
Display screen.
5 5
.
1 0
M
S T P 0 0
. A
5 5
.
1 0
M
S T P 0 0
. A
U L C
N
D
K
S E T T N
I
S
G
L C K
O
D
E
S E T T N
I
S
G
1 0
.
1 0
M
S T P 0 0
. A
F L A
E D I T
A
1 0
.
ESC
ESC
or
5 5
.
1 0
M
S T P 0 0
. A
5 5
.
1 0
M
S T P 0 0
. A
U L C
N
D
K
S E T T N
I
S
G
L C K
O
D
E
S E T T N
I
S
G
1 0
.
1 0
M
S T P 0 0
. A
F L A
E D I T
A
1 0
.
ESC
ESC
or
DANGER
Keypad Interface
This is a condensed version of the full manual.
The complete manual is available for download
at www.franklin-electric.com.
Installation & Operation
800.962.3787 |
www.cerusind.com
Operation
• Ensure that all connections are properly torqued and enclosure is closed
prior to applying power to the device.
• Ensure all mechanical equipment operated by the starter is clear for safe
operation in case of starter activation.
• When in AUTO mode, starter may be activated remotely by the
control system
Operation Modes
ON (HAND)
Press the ON mode button to manually engage motor.
OFF (RESET)
Pressing the OFF mode button manually disengages the motor.
Additionally, the OFF button serves as a manual Reset. Press and
hold OFF for 5 seconds to Reset the starter after a fault trip.
AUTO
When utilizing AUTO mode, the starter is controlled by a remote
Start/Stop command.
LED Status Indicators
MODE LEDs
Illuminates with corresponding mode selection (HAND/OFF/AUTO).
Flashing mode LED signals a fault trip during the last operating
mode. All 3 mode LEDs will flash simultaneously during Shutdown or
Fireman’s Override operation.
RUN LED
Illuminates when starter is given a Run signal and proof of power is
detected. LED will flash when Run signal is present without proof of
power to the motor.
FAULT LED
Illuminates upon a fault condition or overload trip. Starter must be
returned to the OFF mode in order to Reset. A 180 second minimum
cool down period must elapse prior to further operation.
Product improvement is a continual process. Cerus, Mira, Orion
and associated logos are trademarks of Cerus Industrial Corp.
All sales subject to Cerus Terms & Conditions.
Precautions
To prevent injury and property damage, follow these instructions.
Failure to adhere to installation/operation procedures and all
applicable codes may result in hazards as indicated by warning
codes outlined below:
indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury. This signal word is to be limited to the
most extreme situations.
indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against
unsafe practices.
This is the safety alert symbol. Read and follow instructions carefully to
avoid a dangerous situation.
This symbol alerts the user to the presence of “dangerous voltage”
inside the product that might cause harm or electrical shock.
DANGER
WARNING
CAUTION
Safety Instructions
Equipment can start automatically. Lockout/tagout before servicing.
As with all electrical products, read manual thoroughly. Only qualified,
expert personnel should perform maintenance and installation. Contact the
nearest authorized service facility for examination, repair, or adjustment.
Do not disassemble or repair unit unless described in this manual; death
or injury to electrical shock or fire hazard may result. Specifications and
manual data subject to change. Consult factory for additional information.
DANGER
CAUTION
ESC
FLA
RESET
CLASS
5 5
.
1 0
M
S T P 0 0
. A
ESC
Lockout Settings & Overload Adjustment
The IPS Starter is pre-configured to protect the motor based on
customer selected specification. If adjustments need to be made to
any of the protective functions of the IPS starter, the settings must
first be unlocked. To unlock the IPS settings, follow the steps below.
Default Display Screen
Press and hold the UP and DOWN buttons for
2 seconds until the display screen matches the
display at left.
Press the ENTER button to change the menu
from “LOCKED” to “UNLOCKED.”
The lockout feature is now disabled.Press the
ESC key to return to the Default
Display screen.
Adjustments may now be made to the Overload FLA setting and
Ground Fault Level setting. The lockout feature will automatically
re-enable itself after 2 minutes.
Overload Adjustment (Setting Range1.0 - 95.0 Amps)
Once settings are unlocked, follow the steps
below to adjust overload setting.
Press the DOWN arrow once.
Edit FLA Screen
Press ENTER
Use the UP and DOWN keys to make
adjustments.
Press ENTER to save setting.
Press ESC to return to the Default
Display screen.
5 5
.
1 0
M
S T P 0 0
. A
5 5
.
1 0
M
S T P 0 0
. A
U L C
N
D
K
S E T T N
I
S
G
L C K
O
D
E
S E T T N
I
S
G
1 0
.
1 0
M
S T P 0 0
. A
F L A
E D I T
A
1 0
.
ESC
ESC
or
5 5
.
1 0
M
S T P 0 0
. A
5 5
.
1 0
M
S T P 0 0
. A
U L C
N
D
K
S E T T N
I
S
G
L C K
O
D
E
S E T T N
I
S
G
1 0
.
1 0
M
S T P 0 0
. A
F L A
E D I T
A
1 0
.
ESC
ESC
or
DANGER
Keypad Interface
This is a condensed version of the full manual.
The complete manual is available for download
at www.cerusind.com or call 800.962.3787.
Installation & Operation