Gb704 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you. S/n: 3213 and above please contac...
2 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Table of contents description page warnings .................................................................................................................................................................
3 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Safety warnings general safety rules: 1. For multiple hazards, read and understand the safety instructions before installing, operating, repairing, maintaining, changing accessories on, or working near ...
4 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Air pressure air pressure air piston air pressure air pressure air pressure principle of operation when the actuator lever assy is depressed, the pressurized air inside of the tool is released allowing ...
5 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. How to use the gb704 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pu...
6 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Description warning : the balance of this tool is designed for horizontal use and is not ergonomically best suited for all applications. Gage bilt will be pleased to advise for your specific application...
7 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Filling and bleeding tool note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), install...
8 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a regular daily basis for da...
9 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Head remove nose assembly and adapter from tool before attempting disassembly of head cylinder assy (704108). Warning: dispose of hydraulic oil in accordance with applicable regulations. Remove end cap ...
10 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Handle to inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assy (704108) first. For complete disassembly, start by removing base ...
11 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Dexron® iii oil safety data first aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid ...
12 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Gb704 - selection chart fastener diameter straight right angle (3) offset 1/8 456max-701-17 (2) 456max-704-54ra (2) 456max-704-43os (2) 5/32 456max-704-35 (2) 3/16 456max-749-35 (4,2) 3/32 3c-704a-16 3...
13 6/11 rev. 9/14 gb704 s/n: 3213 and above please contact gage bilt for all other serial numbers. Seller warrants that all goods covered by this catalog will conform to applicable specifications and will replace or repair, f.O.B. Our plant, any goods providing defective from faulty workmanship, or ...
