Gb713 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you..
2 7/11 rev 10/14 table of contents description page warnings.....................................................................................................................................................................................3 principle of operation……………………………………………………………………………………………...
3 7/11 rev 10/14 warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screws (402482). Pressurized hydraulic oil may cause severe personal injury....
4 7/11 rev 10/14 principle of operation when the air actuator assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool assy causing the air to be redirected. The air is directed to the top of the air piston assy, moving it in a downward d...
5 7/11 rev 10/14 how to use the gb713 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in the air. Personal injury from fastener ejecting may occur. Warning: a...
6 7/11 rev 10/14 cleaning and lubricating procedure daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine oil, or an equivalent cleaner/ lubricant, follow instructions below. 1. Disconnect tool vacuum line (if equipped). 2....
7 7/11 rev 10/14 filling and bleeding tool note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), installed in the head cylinder assy (713121). Severe personal injury may result. Caution...
8 7/11 rev 10/14 troubleshooting providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 1. More than one pull is required to break rivet. A) tool needs to be bled. (see filling and bleeding instructions.) b) spring has fatigued, replace. C) jaws are strippe...
9 7/11 rev 10/14 overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on gage bilt proce...
10 7/11 rev 10/14 head warning: dispose of hydraulic oil in accordance with all environmental regulations applicable in your area. Remove nose assembly from tool before attempting disassembly of head assy. Remove end cap (713217). Push against threaded end of piston (713211) to slide it out of head ...
11 7/11 rev 10/14 handle to inspect air cylinder bore, remove o’ring (s12) and base cover (744124). Any further disassembly will require removal of the head cylinder assy (713121) first. For complete disassembly, start by removing parts o’ring (s12) and base cover (744124). Next, holding tool uprigh...
12 7/11 rev 10/14 dexron® iii oil safety data first aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated...
13 7/11 rev 10/14 gb713 - selection chart fastener dia. 3/16 lb06-722-20 lb06-722-60 1/4 lb08-722-20 lb08-722-60 3/16 mg06-722-20 mg06-722-60 1/4 mg08-722-20 mg08-722-60 1/8 sb04-752c-20 sb04-752c-45 sb04-752a-43os 5/32 sb05-752c-20 sb05-752c-45 sb05-752a-43os sb05-752c-80 3/16 sb06-752b-20 sb06-752...
14 7/11 rev 10/14 dexron® is a registered trademark of general motors corporation. Lubriplate® is a registered trademark of fiske brothers refining co. Loctite® is a registered trademark of henkel corporation. Seller warrants that all goods covered by this catalog will conform to applicable specific...
