Gb722 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you. S/n: 1753 and above please contac...
2 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Specifications weight - 5.50 lbs. (2.49 kg) air pressure req'd - 90-100 psi. (6.2-6.9 bar) air consumption - .16 scf/cycle (4.53 l/cycle) hydraulic oil - automatic transmission oil, dexron iii, or equivalent. Sett...
3 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screws...
4 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Principle of operation when the actuator lever assy is depressed, the pressurized air inside the tool is released allowing spring pressure to move the valve spool assy causing the air to be redirected. The air is ...
5 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. How to use the gb722 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in...
6 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine oil, or an equivalent cleaner/lubricant, follow instructions below. 1. Disconnect ...
7 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Filling and bleeding tool note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), installed in the h...
8 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a regular daily basis for damage or wea...
9 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Head remove nose assembly from tool before attempting disassembly of head cylinder assembly (752119). Remove end cap (722317). Push against threaded end of piston (752507) to slide it out of head cylinder assy (75...
10 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Handle to inspect air cylinder bore, remove base cover (704125) and o'ring (s725). Any further disassembly will require removal of the head cylinder assy (752119) first. For complete disassembly, start by removin...
11 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. First aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution,...
12 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Gb722 - selection chart fastener dia. *right angle 2 3/16 lb06-722-20 lb06-722-60 1/4 lb08-722-20 lb08-722-60 3/16 mg06-722-20 mg06-722-60 1/4 mg08-722-20 mg08-722-60 3/16 mgl06-752a-21 mgl06-752a-61 mgl06-713b-5...
13 rev. 1/15 s/n: 1753 and above please contact gage bilt for all other serial numbers. Seller warrants that all goods covered by this catalog will conform to applicable specifications and will replace or repair, f.O.B. Our plant, any goods providing defective from faulty workmanship, or material, f...