Gb743 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you. S/n: 2269 and above please contac...
2 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Specifications hand held weight - 6.25 lbs. (2.83 kg) air pressure req'd - 90-100 p.S.I. (6.2-6.9 bar) air consumption - .29 scf/cycle (8.21 l/cycle) hydraulic oil - automatic transmission oil, dexron® iii, or eq...
3 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screw...
4 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Principle of operation when the air actuator assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool assy causing the air to be redirected. The air i...
5 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. How to use the gb743 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet i...
6 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Torque specifications button head cap screws (402479) = 40 inch lbs. Packing plug (744118) = 45 foot lbs. Flexlock nut (400559) = 40 inch lbs. End cap (743214) = 45 foot lbs. Button head cap screws (402482) = 35-...
7 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Filling and bleeding tool note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), installed in the ...
8 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any ...
9 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Head warning: dispose of hydraulic oil in accordance with all environmental regulations applicable in your area. Remove nose assembly from tool before attempting disassembly of head assembly. Remove end cap (7432...
10 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Handle to inspect air cylinder bore, remove o’ring (s12) and base cover (744124). Any further disassembly will require removal of the head cylinder assy (743108) first. For complete disassembly, start by removin...
11 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. First aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution...
12 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Xx-703-18 xx-734a-20 xx-743-24 see chart see chart see chart 10757-1 anvil holder 20518 collet see chart 405371 spring 70820 nut see chart 10935-1 anvil holder 10951-2 anvil holder 28819 collet 20867 collet see ...
13 rev. 10/14 s/n: 2269 and above please contact gage bilt for all other serial numbers. Dexron® is a registered trademark of general motors corporation. Lubriplate® is a registered trademark of fiske brothers refining co. Loctite® is a registered trademark of henkel corporation. Seller warrants tha...
