Gb745 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you..
2 rev. 9/14 gb7045 specifications hand held weight - 7.20 lbs. (3.26 kg) air pressure req'd - 90-100 p.S.I. (6.2-6.9 bar) max. Air consumption - .29 scf/cycle (8.21 l/cycle) hydraulic oil - automatic transmission oil, dexron iii, or equivalent. Setting stroke - .620" (15.75 mm) rated pull load - 6,3...
3 rev. 9/14 gb7045 safety warnings general safety rules: 1. For multiple hazards, read and understand the safety instructions before installing, operating, repairing, maintaining, changing accessories on, or working near the assembly power tool for non-threaded mechanical fasteners. 2. Only qualifie...
4 rev. 9/14 gb7045 image may not reflect actual tool principle of operation when the air actuator assy is depressed, the pressurized air inside the tool is released allowing spring pressure to move the valve spool assy, causing the air to be redirected. The air is directed to the top side of the air...
5 rev. 9/14 gb7045 how to use the gb745 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in the air. Personal injury from fastener ejecting may occur. Warning:...
6 rev. 9/14 gb7045 torque specifications button head cap screws (402479) = 40 inch lbs. Packing plug (744118) = 45 foot lbs. Flexlock nut (400559) = 40 inch lbs. End cap (745816) = 45 foot lbs. Button head cap screws (402482) = 35-40 inch lbs. (do not over-tighten) description covered under patent n...
7 rev. 9/14 gb7045 filling and bleeding instructions note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), installed in the head cylinder (745366). Severe personal injury may result. Ca...
8 rev. 9/14 gb7045 troubleshooting providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 1. More than one pull is required to break rivet. A) tool needs to be bled. (see filling and bleeding instructions.) b) spring has fatigued, replace. C) jaws are strip...
9 rev. 9/14 gb7045 head remove nose assembly from tool before attempting disassembly of head cylinder (745366). Remove end cap (745816). Push against threaded end of piston (745310) to slide it out of head cylinder (745366). Be careful not to damage threads or cause burrs on polished piston rod surf...
10 rev. 9/14 gb7045 handle to inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (745366) first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap screws (4024...
11 rev. 9/14 gb7045 first aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material f...
12 rev. 9/14 gb7045 gb745- selection chart fastener dia. 1/8 4a-745c-23 4a-745c-48 4a-752a-43os 6 5/32 5a-745c-23 5a-745c-48 5a-752a-43os 6 3/16 6a-745b-23 6a-745b-48 6a-752a-43os 6 1/4 smls08-755-23 smls08-755-48 smls08-204d-27os 13/64 asp06-745b-23 asp06-745c-48 asp06-752a-43os 6 17/64 asp08-745b-...
13 rev. 9/14 gb7045 dexron® is a registered trademark of general motors corporation. Lubriplate® is a registered trademark of fiske brothers refining co. Loctite® is a registered trademark of henkel corporation. Magna-grip® is a registered trademark of alcoa inc. Seller warrants that all goods cover...
