Gb751 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you. S/n: 1324 and above please contac...
2 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Specifications hand held weight - 4.50 lbs. (2 kg) air pressure req'd - 90-100 p.S.I. (6.2-6.9 bar) air consumption - .16 scf/cycle (4.53 l/cycle) hydraulic oil - automatic transmission oil, dexron iii, or eq...
3 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap s...
4 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Principle of operation when the actuator lever assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool assy causing the air to be redirected. The...
5 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. How to use the gb751 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull riv...
6 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Torque specifications button head cap screws (a-928) = 40 inch lbs. Flexlock nut (400559) = 40 inch lbs. Packing plug (704118) = 45 foot lbs. End cap (703114) = 45 foot lbs. Button head cap screws (402482) = ...
7 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Filling and bleeding tool note: air bleeder assy (704153) is required. Warning: do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (s572), installed in ...
8 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. ...
9 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Head remove nose assembly and adapter from tool before attempting disassembly of head assy. Remove end cap (703114). Push against threaded end of piston (751307) to slide it out of head cylinder assy (703109)...
10 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Handle to inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assy (703109) first. For complete disassembly, start by removing base cover ...
11 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. First aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precau...
12 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Gb751- selection chart fastener dia. Right angle 1 offset 1/8 smls04-752c-20 smls04-752c-45 smls04-751b-54ra smls04-752a-43os 5/32 smls05-752c-20 smls05-752c-45 smls05-751b-54ra smls05-752a-43os 3/16 smls06-...
13 6/11 rev 10/14 s/n: 1324 and above please contact gage bilt for all other serial numbers. Dexron® is a registered trademark of general motors corporation. Lubriplate® is a registered trademark of fiske brothers refining. Loctite® is a registered trademark of henkel corporation. Seller warrants th...
