Gb784 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you..
2 rev. 12/12 specifications hand held weight - 6.25 lbs. Air pressure req'd - 90-100 p.S.I. Air consumption - 3 c.F.M., based on 20 cycles/min. Hydraulic fluid - automatic transmission fluid, dexron iii, or equivalent. Setting stroke - .940" rated pull load - 2,650 lbs. Noise level - 81.5 db (a) vib...
3 rev. 12/12 warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screw (402482). Pressurized hydraulic fluid may cause severe personal injury. Wa...
4 rev. 12/12 air pressure air pressure air piston air pressure air pressure air pressure principle of operation when the trigger is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool causing the air to be redirected. The air is directed to ...
5 rev. 12/12 how to use the gb784 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in the air. Personal injury from fastener ejecting may occur. Warning: air i...
6 rev. 12/12 description warning : the balance of this tool is designed for horizontal use and is not ergonomically best suited for all applications. Gage bilt will be pleased to advise for your specific application. The gb784 is a pneumatic-hydraulic hydro-shift tool designed specifically for the e...
7 rev. 12/12 filling and bleeding tool warning do not cycle tool without air bleeder, or the screw and stat-o-seal, installed in tool head. Severe personal injury may result. Caution before filling handle, air piston should be all the way down. Caution when forcing piston rod assembly downward with ...
8 rev. 12/12 overhaul the disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing seals, always apply ...
9 rev. 12/12 handle to inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (784221) first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap screws (402479). Li...
10 rev. 12/12 dexron® iii oil safety data first aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To...
11 rev. 12/12 nose assemblies: nose assemblies are not furnished with the tool and must be purchased separately. In ordering heads be sure to specify the shank diameter and head style (universal or countersunk) of the rivets to be in- stalled. The following pulling heads will fit directly on the gb7...
12 rev. 12/12 setting the shift point: the shift point must be adjusted to ensure the flushness of the rivet stem after installation. To adjust: 1. Connect the tool to a clean dry air source of 90 psi to 100 psi. Remove nut. 2. Hand tighten small end of 784159 gage onto piston. 3. Depress trigger an...
13 rev. 12/12 dexron® is a registered trademark of general motors corporation. Cherry® and cherrylock® are registered trademarks of cherry aerospace. Lubriplate® is a registered trademark of fiske brothers refining. Seller warrants that all goods covered by this catalog will conform to applicable sp...
