- DL manuals
- GAI-Tronics
- Telephone
- 1090
- Installation and user manual
GAI-Tronics 1090 Installation and user manual
Summary of 1090
Page 1
Doc. No. 502-20-0122-001 iss1. October 2007 (cn22148) installation and user guide hands-free telephones 1090/1099 models vandal resistant (vr) and help point gai-tronics.
Page 2: Contents
2 vr & help point contents 1. Safety and care information....................................................................... 3 2. Product description .................................................................................... 3 2.1. Changes from previous versions...........................
Page 3: Safety and Care Information
Vr & help point 3 1. Safety and care information ▲ the safety of the user/installer relies on the isolation of the telephone network and not on the earthing of the case ▲ please read these instructions thoroughly before starting installation. These products must be installed by competent personnel f...
Page 4: Operation / Testing
4 vr & help point • sensitive microphone, protected by semi porous membrane and aluminium grille • stainless steel auto-dial button(s) • call status led • auto-dial numbers are remotely programmable • line powered operation (optional supplementary power supply available) • optional cast aluminium re...
Page 5: 4. Smart
Vr & help point 5 3.3. Ending the call there is no direct way for a user to end a call from the unit. The unit will close down and release the line on receipt of the following signals, usually when the remote party clears: • line polarity reversal • a line break (sometimes referred to as a “k break”...
Page 6
6 vr & help point competent personnel. Where the telephone faceplate is mounted into an enclosure or recess other than the standard gai-tronics backbox, then additional care must be taken that wiring and proximity to conducting surfaces complies with the requirements of the r&tte directive - 1999/5/...
Page 7
Vr & help point 7 cable entry hole and tighten, so that its sealing washer is compressed against the enclosure surface. 4. Proceed with chosen mounting method below 5.2.1 wall mounting 1. Using a suitable tool, punch out the 4 holes in the rear enclosure, taking care not to damage or dislodge the pl...
Page 8
8 vr & help point 5.2.2 pole mounting kit no 100-02-0208-001 this accessory is for mounting gai-tronics telephones on to the side of round poles of 100mm to 200mm diameter, or on to square or rectangular section uprights of 100mm to 150mm across the mounting surface. Note: banding straps (large scal...
Page 9
Vr & help point 9 5.3. Flush mounting to flush-mount the telephone to a wall: 1. Prepare a recess (at least 50mm deep) in the wall according to the dimensions shown. 2. Mark the wall with hole centres based on the dimensions shown (155 x 326mm). If necessary offer the faceplate up to the wall to che...
Page 10: 6. Connections
10 vr & help point 6. Connections 6.1. Standard connections connect the telephone line a and b to the main terminal block con1 as shown. The centre earth terminal is intended as an optional connection to a local earth for the purpose of enhanced protection from lightning transients, and is not requi...
Page 11
Vr & help point 11 6.3. Optional relay outputs gai-tronics hands-free telephones can be equipped with external relay outputs, controlled by the telephone software. Note – these optional connections are only available if specifically ordered, and a supplementary power supply (see section 6.2) is requ...
Page 12
12 vr & help point 7. Programming and option settings programming and option setting is done remotely by sending commands down the telephone line to the unit. This can be done by either using a tone phone, or by using gai-tronics tma - a pc software application. 7.1. Quick programming guide (using a...
Page 13
Vr & help point 13 2) has the default pin code already been changed by another user? Check your own records and enter the correct pin code as necessary. Note that this problem can only occur if you are carrying out a re- programming exercise. Telephones always leave the factory with the value **0000...
Page 14: 8. Aftercare
14 vr & help point full details on the configuration and use of tma are provided with the package itself. Contact gai-tronics for further details. Tma part numbers: tma package (uk): 100-02-0309-001 tma package (europe): 100-02-0309-002 each package includes the tma software (including comprehensive...
Page 15: 9. Technical
Vr & help point 15 9. Technical specifications operational requirements systems. • analogue public switched telephone network (pstn) • private automatic branch exchange (pabx) not suitable for connection to: • payphone extensions • public emergency telephone system (pets) telephone line parameters (...
Page 16
16 vr & help point induction loop (optional) suitable for inductive coupling to hearing aids having a `t' switch position. Supplementary power required. Dialling and recall mode mf only. Tbr only. Monitored faults and sensors • hookswitch • brown out (power failure) • call log full • 4 auxilliary in...
Page 17
Vr & help point 17 recycling information the symbol shown here and on the product means that the product is classed as electrical or electronic equipment and should not be disposed with other household or commercial waste at the end of its working life. The waste of electrical and electronic equipme...
Page 18
18 vr & help point compliance to standards european directives 1999/5/ec – european radio & telecommunications terminal equipment directive. 2002/96/ec - waste electrical and electronic equipment (weee) directive 2002/95/ec - restriction of the use of certain hazardous substances in electrical and e...
Page 19: 10. Ce Declaration
Vr & help point 19 10. Ce declaration.
Page 20: Gai-Tronics
20 vr & help point gai-tronics a division of hubbell ltd. Brunel drive stretton park burton on trent de13 0bz england tel: 01283 500500 fax: 01283 500400 www.Gai-tronics.Co.Uk the policy of gai-tronics is one of continuous improvement, therefore the company reserves the right to change specification...