- DL manuals
- GAI-Tronics
- Telephone
- Commander CB
- Installation And User Manual
GAI-Tronics Commander CB Installation And User Manual
Summary of Commander CB
Page 1
Doc. No. 502-20-0099-001 iss3. Dec 2007 (cn33056-001) installation and user guide titan cb (1064) commander cb (1064) weather resistant telephones gai-tronics titan commander.
Page 2: Contents
2 titan cb, commander cb contents 1. Safety and care information....................................................................... 3 2. Product description .................................................................................... 3 2.1. Changes from previous versions....................
Page 3: Safety and Care Information
Titan cb, commander cb 3 1. Safety and care information ▲ the safety of the user/installer relies on the isolation of the telephone network and not on the earthing of the case ▲ the spring-loaded door (titan models only, where fitted) can close sharply. Take care not to trap fingers etc., during ins...
Page 4
4 titan cb, commander cb 2.2. Titan features titan is a family of rugged, weather-resistant metal-bodied telephones available with a range of handset types, keypad configurations, colours and enclosures, based around a common faceplate style. Most titans are equipped with a heavy-duty spring-loaded ...
Page 5: Operation / Testing
Titan cb, commander cb 5 3. Operation / testing the cb telephone has no buttons and no means of dialling or signalling. It can only be used to make calls where calls are routed by the exchange, for example the bt direct connect service or pabxs or concentrators specifically configured to do so. Seek...
Page 6: 4. Installation
6 titan cb, commander cb 4. Installation 4.1. General important all possible measures must be taken to ensure water, fluid or dust does not contaminate the internal components of the telephone whilst unpacking, preparing and installing the telephone in inclement weather conditions or by negligence. ...
Page 7
Titan cb, commander cb 7 3. The titan telephone is intended for vertical installation to a wall or pole. Select the required mounting method (section 5) and mount the rear enclosure first where applicable. 4. Route the required cables through glands as appropriate, and make connections and option se...
Page 8
8 titan cb, commander cb only fit a second gland if a separate cable is required to the phone (for example for an additional hook contact). 2. Select the appropriate sized gland: use the smaller gland for cables diameters 4 - 7mm. Use the larger gland for cable diameters 8 - 13mm. 3. From the outsid...
Page 9
Titan cb, commander cb 9 of the eight holes are required - the outer ones are recommended. The inner holes are provided to be compatible with older-style mounting posts, and should be left intact if not used. If the inner holes are used they must be fitted with the supplied plastic bushes. Warning:....
Page 10
10 titan cb, commander cb 5.2.2 pole mounting kit no 100-02-0208-001 this accessory is for mounting gai-tronics telephones on to the side of round poles of 100mm to 200mm diameter, or on to square or rectangular section uprights of 100mm to 150mm across the mounting surface. Note: banding straps (la...
Page 11
Titan cb, commander cb 11 to flush-mount the telephone to a wall: 1. Prepare a recess (at least 50mm deep) in the wall according to the dimensions shown. 2. Mark the wall with hole centres based on the dimensions shown (155 x 326mm). If necessary offer the faceplate up to the wall to check alignment...
Page 12
12 titan cb, commander cb 5.3. Commander 5.3.1 wall mounting to ensure weatherproof integrity when wall mounted, external cables should enter the enclosure from the bottom via the 20mm gland entries provided. Important: do not drill any extra holes as this will invalidate your warranty. 1. Remove ru...
Page 13
Titan cb, commander cb 13 4. Continue the installation by making the appropriate connections (section 6). 5. Reconnect the handset / hookswitch. Secure the telephone front casing to the rear casing. 5.3.2 pole mounting kit no 100-02-0208-001 this accessory is for mounting gai-tronics telephones on t...
Page 14
14 titan cb, commander cb 5.3.3 desk mounting / rake for horizontal surfaces greater than 150 x 280mm use the free-standing desk mounted method below. To provide a 'rake' for convenient operation, the front casing may be turned through 180° before it is fitted to the rear casing. Thus the cable entr...
Page 15
Titan cb, commander cb 15 important : if only one gland entry is used, the blanking plug fitted to the second gland position must be left in place. 6.1. Standard connections and timer setting connect the telephone line a and b to the main terminal block tb2 as shown. The centre earth terminal is int...
Page 16: 7. Aftercare
16 titan cb, commander cb the switch is operated by the presence of the handset on the stowage. It is a voltage-free switch providing functional and basic insulation from the telephone network. It is intended to be connected to a tnv-3 or selv circuit as defined by en 60950-1:2001. Switch maximum ra...
Page 17: 8. Technical
Titan cb, commander cb 17 8. Technical specifications operational requirements systems. • analogue public switched telephone network (pstn) • private automatic branch exchange (pabx) • railway infrastructure concentrator. Not suitable for connection to: • payphone extensions • public emergency telep...
Page 18
18 titan cb, commander cb compliance to standards european directive 1999/5/ec – european radio & telecommunications terminal equipment directive (r&tte). Emc en55022:1998 – information technology equipment. Radio disturbance characteristics. En55024:1998 – information technology equipment. Immunity...
Page 19: 9. Ce
Titan cb, commander cb 19 9. Ce declaration.
Page 20: Gai-Tronics
20 titan cb, commander cb gai-tronics a division of hubbell ltd. Brunel drive stretton park burton on trent de13 0bz england tel: 01283 500500 fax: 01283 500400 www.Gai-tronics.Co.Uk the policy of gai-tronics is one of continuous improvement, therefore the company reserves the right to change specif...