- DL manuals
- GAI-Tronics
- Telephone
- PHP400
- Installation And User Manual
GAI-Tronics PHP400 Installation And User Manual
Summary of PHP400
Page 1
Doc. No. 502-20-0130-005 iss 5. Aug 2015. (cn38606-001) installation and user guide php400 help point gsm version (1090/1099 series) 230v ac power supply gai-tronics a division of hubbell ltd..
Page 2
Php400 gsm help point. 2 contents 1. Safety and care information ..................................................................................... 3 2. Product description and features ............................................................................ 3 3. Operation / testing ............
Page 3
Php400 gsm help point. 3 1. Safety and care information ▲ important: this equipment contains hazardous voltages ▲ this equipment must be earthed ▲ mains supply must be isolated elsewhere before opening the case. ▲ cabling and connections must be in accordance with local electrical safety regulations...
Page 4
Php400 gsm help point. 4 the help point casing is a two-part construction with electronics in both sections. The 2 sections are held together with 4 security screws though the sides, and there are several cables between the 2 sections. Cable entry points are provided to top and bottom of the casing....
Page 5
Php400 gsm help point. 5 3. Operation / testing 3.1. Making a call to make a call, press the required button and wait for connection. The unit will seize the line and then automatically dial the pre-programmed number. 3.2. Answering calls to receive a call, press any button when ringing is heard. 3....
Page 6
Php400 gsm help point. 6 this level may have to increase if the ambient noise level at the help point is high, and in any event correct operation cannot be guaranteed in ambient noise levels exceeding 80dba. 4. Installation and dimensions 4.1. General important all possible measures must be taken to...
Page 7
Php400 gsm help point. 7 2. Ensure that a suitable sim card is available (no sim is supplied with the help point). Important: ensure that the sim is activated and not locked. If the sim is locked there is no way of unlocking it from the help point and the help point will not function. It is also rec...
Page 8
Php400 gsm help point. 8 9. Before refitting the front case section, set up the gsm terminal as follows. Remove the 2 screws holding the gsm terminal retaining bracket to allow access to the cover and sim holder. 10. Remove the cover from the gsm terminal to reveal the sim card holder, fir the sim a...
Page 9
Php400 gsm help point. 9 13. Note that the gsm terminal has been set to power up as soon as power is applied, without the need to press its rest button. This results in the green status led being on permanently in the standby state, not flashing as indicated in the picture above. 14. Connect inducti...
Page 10
Php400 gsm help point. 10 5. Connections 5.1. Connections between front and rear sections 5.2. Dc power connections connect mains power to the terminal block as shown on the connection label. See drawing on previous page. The mains supply must be provided by a 2 pole disconnection device with a mini...
Page 11
Php400 gsm help point. 11 5.4. Internal power connections the php400 help point is provided with a 12v power supply unit, required to power the induction loop and telephone module itself. The power input is on con1a as shown and is connected to the psu in the rear section via screw terminals in a 2 ...
Page 12
Php400 gsm help point. 12 6. Programming and option settings programming and option setting is done remotely by sending dtmf tone commands to the unit. This can be done by either using a tone phone, or by using gai-tronics tma – a pc software application. 6.1. Dtmf tones over gsm note that sending d...
Page 13
Php400 gsm help point. 13 6.3. Further programming options in addition to programming auto-dial numbers, several other features can be programmed using a tone-phone. 6.3.1 time-out the call time out is factory set to 7 minutes, meaning that the phone will drop the call and go back on hook electronic...
Page 14
Php400 gsm help point. 14 where n is the level in db, minimum 10, maximum 31, the factory default setting is 26. This command must be entered between entering the pin and closing the phone down with *99 (ie during step 5 of the quick programming guide above). Caution - changing this level may cause ...
Page 15
Php400 gsm help point. 15 9. Repairs and spare parts. It is recommended that help points are returned to gai-tronics for service or repair, to ensure that any repairs are fully tested. In the event of work having to be carried out on site, the following spare parts are available: part no description...
Page 16
Php400 gsm help point. 16 10. Technical specifications operational requirements systems. • quad-band gsm phase 2/2+ 850/900/1800/1900 mhz • minimum signal strength typically -90bbm product features power supply • input requirement 88-264v, 47-63hz, 0.7a max • integral isolated mains to 12vdc power s...
Page 17
Php400 gsm help point. 17 compliance to standards european directives 1999/5/ec – european radio & telecommunications terminal equipment directive. 2011/65/ec - restriction of the use of certain hazardous substances in electrical and electronic equipment (recast) (rohs 2) directive 2002/96/ec - wast...
Page 18
Php400 gsm help point. 18 11. Ce declaration a copy of the current ce declaration of conformity is available from our website. Www.Gai- tronics.Org/support/certificates-approvals/.
Page 19
Php400 gsm help point. 19.
Page 20
Php400 gsm help point. 20 gai-tronics a division of hubbell ltd. Brunel drive, stretton park burton on trent, de13 0bz england tel: 01283 500500, fax: 01283 500400 www.Gai-tronics.Co.Uk the policy of gai-tronics is one of continuous improvement, therefore the company reserves the right to change spe...