1. DL manuals
  2. GalileoSky
  3. Touch terminals
  4. GLONASS
  5. User Manual

GalileoSky GLONASS User Manual

Summary of GLONASS

  • Page 1

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 1 terminals galileosky glonass/gps v5.1 user’s manual firmware 0223 quality reliability simplicity.

  • Page 2: Contents

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 2 contents introduction ........................................................................................................................................................ 5 1. Package .............................................

  • Page 3

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 3 8.2 connecting digital fuel sensors using rs232 protocol ........................................................................... 28 8.3 connecting digital fuel sensors using rs485 protocol ........................................

  • Page 4

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 4 9.7 routes for autoinformer ........................................................................................................................ 57 9.8 trusted ibutton keys ........................................................

  • Page 5: Introduction

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 5 introduction galileosky ltd. Produces galileosky terminals for gps and glonass real time vehicles monitoring. The terminals determine the mobile object location recording the time and route as points with geographical coordinates ...

  • Page 6

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 6 the terminal provides the following opportunities: vehicles monitoring in real time; a detailed turn by turn track (without any extra points in a straight track); voice communication with the traffic dispatcher; gsm/3g enabled rem...

  • Page 7: Package

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 7 1. Package the standard package includes the galileo terminal (hereinafter referred to as the terminal) and a pin connector with contacts. Everything extra should be bought separately. Exposed face 1. Main connector 2. Sim 0 3. Si...

  • Page 8: Technical Specifications

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 8 2. Technical specifications parameter description analog-discrete and pulse frequency inputs 8 pcs; voltage range -0-33v; maximum measured frequency-4 khz; input resistance of every input is 14 kohm to the ground. Transistor outpu...

  • Page 9: Physical Specifications

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 9 3. Physical specifications operating temperature range -40...+85 °c storage temperature -40...+85 °c relative humidity 0...90% (0...35 °c); 0...70% (35...55 °c) performance (height above the sea level) 0-2000 m storage 0-10000 m c...

  • Page 10: Safe Operating Rules

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 10 4. Safe operating rules before using the terminal study the instructions of gsm/3g/gprs devices safe operating. Make sure the polarity is correct when connecting to the power supply. The device should be connected straight to the...

  • Page 11: Connecting

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 11 6. Connecting 6.1 connecting glonass aerial carefully screw the aerial to the terminal, the upper side is above. To have a better view of the sky it is recommended that the aerial should be mounted on the vehicle roof, windscreen...

  • Page 12: 6.3 Inserting Sim-Card

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 12 6.3 inserting sim-card use a sim-card with activated gprs and sms services. Insert the card carefully without applying excessive force . 1) to eject the sim holder press the indicated place as shown in the picture with something ...

  • Page 13: Terminal Units Performance

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 13 7. Terminal units performance 7.1 discrete-analog inputs (dai) to attach external sensors the terminal has 8 discrete-analog inputs which are pulse-frequency at the same time. Each input’s function is set in the terminal settings...

  • Page 14

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 14 4.1.1 pulse count in case of a renewable counter the maximum pulse number can be 65535, after that the number is reset to zero. If there is pulse at input, the correspondent bit will be set in the status of inputs field, and a po...

  • Page 15

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 15 7.2 determination of strike and incline all devices can determine the terminal`s strike and incline. Accelerometer axis directions: to determine strike: 1. Install the terminal so as one of the accelerometer axis looks vertically...

  • Page 16

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 16 7.3 economical driving "ecodrive" and determination of the driving style the terminal can detect rapid acceleration, braking, harsh turns and strikes on bumps. For correct operation of this function, the terminal must detect its ...

  • Page 17: 7.5 Autoinformer Function

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 17 7.5 autoinformer function autoinformer function may be used for automatic (without participation of the driver) public transport stops announcement with the use of a satellite navigation system. The main difference from analogous...

  • Page 18

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 18 latitude and longitude values are entered through the point “.” (for example: 57.9842) where the value after point – is degree fractions. To transfer minutes into degree fractions (xdegr.Ymin.) use the following expression xdegr....

  • Page 19: 7.6 Signaling Function

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 19 7.6 signaling function signaling function allows assigning the response to: 1. Analog input state change; 2. Strikes and inclines (accelerometer data); 3. Location change; 4. Speeding; 5. Ibutton or rfid card connection. The term...

  • Page 20

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 20 7.7 monitoring data transmission terminal allows specifying the list of preferred gsm/3g-networks. The main priority is given to the networks from the beginning of the list. Every network is specified with country’s code and netw...

  • Page 21

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 21 the second algorithm is always used for remote firmware updating; the terminal attempts to get the connection to the server with firmware through sim 0, and if it fails - through sim 1. 7.10 gprs traffic costs optimization gprs-t...

  • Page 22: 7.13 Geofences

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 22 7.12 stels mode and packet transmission in this mode the terminal switches off gsm/3g-unit and contacts only according to a strict schedule, which allows decreasing the internet traffic and power consumption. Stels mode settings ...

  • Page 23: 7.14 Power Saving

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 23 7.14 power saving to reduce power consumption of the terminal in the operating mode, perform the following steps: 1. For rs232 port, execute rs2320 0 or or specify "nothing" as the peripheral type in the configurator. 2. Turn off...

  • Page 24: 8.1 Can-Interface

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 24 8. Connecting external peripheral 8.1 can-interface the terminal allows extracting information from the can-bus. The following protocols are supported: – j1939 (fms). According to this protocol, the terminal is not a device trans...

  • Page 25

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 25 8.1.2 fms mode this mode is activated in all terminals by default; it allows retrieving and decoding messages relevant to fms protocol: total fuel consumption: the amount of fuel the vehicle had used since it was made; tank fuel ...

  • Page 26

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 26 j1939_user-11bit mode is set similarly. 8.1.4 j1979_scaner mode this mode is used to define data transfer rate and identifier length according to j1979 protocol. If the parameters of transfer are known, it is recommended to use t...

  • Page 27

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 27 8.1.6 different variants of connection to the can-bus 1. Direct connection. Attention! If the terminating resistor (is shown with a dotted line in the diagram) is not installed on the vehicle side, it should be installed. Its pre...

  • Page 28

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 28 8.2 connecting digital fuel sensors using rs232 protocol the order of connection: 1. Connect rxd, txd and gnd sensor contacts to terminal txd0, rtd0 and gnd contacts (section contacts description ). Attention! The terminal and se...

  • Page 29

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 29 8.3 connecting digital fuel sensors using rs485 protocol the order of connection: 1. Connect rs485_a; rs485_b, gnd sensor contacts to terminal rs485_a; rs485_b, and gnd contacts (section contacts description ). The sensor power s...

  • Page 30

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 30 8.4 connecting galileosky photo camera to the device galileosky v3.0.0 non-dust-proof-and-moisture- proof galileosky v3.0.3 and v3.1.0 hermetically-sealed data transmission interface: rs232 data transmission interface: rs232 or r...

  • Page 31

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 31 the order of connection cameras via rs232 interface : 1. The camera rxd, txd, gnd contacts should be connected to the device txd0, rxd0, gnd contacts (section contacts description). Attention! The terminal and the camera grounds ...

  • Page 32

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 32 8.5 connecting 1wire sensors it is possible to connect different sensors working through 1-wire interface, and they can operate simultaneously. 8.5.1 connecting ibutton (ds1990, ds1982) identification key there are several identi...

  • Page 33

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 33 8.5.2 connecting ds18s20 (ds1820, ds18b20) thermometers and ds1923 temperature and humidity sensors it is possible to connect up to 8 ds18s20 thermometers and 8 ds1923 sensors. To use the sensors connect them to 1-wire and gnd co...

  • Page 34

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 34 8.8 connecting passenger flow registration Ш2 sensors the terminal supports connection of up to 16 Ш2 sensors through 8 discrete-analog inputs (dai) in0-in7 (contacts description). Connection order of one Ш2 sensor through resist...

  • Page 35

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 35 8.9 connecting garmin navigators supporting fmi protocol the terminal can serve as a gateway for garmin fmi protocol packets transmission to the server and back. Garmin fmi protocol enables: drivers identification by code numbers...

  • Page 36: 8.11 Connecting Can-Log

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 36 8.11 connecting can-log the can-log device is designed for can-bus data reading. It allows getting the data about: - total time of engine operation; - total mileage of a vehicle; - whole fuel consumption of a vehicle since the da...

  • Page 37

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 37 8.13 connecting ci5010a weight indicator the ci-5010a weight indicator is designed to measure, control and indicate electrical signals produced by weight measuring strain gages sensors. It can be connected to the terminal via rs2...

  • Page 38

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 38 1. Connect the rs485a, rs485b, gnd contacts of the terminal and the rs485a (contact 1), rs485b (contacts 2), gnd (contact 6) of the dosimeter correspondingly. Dosimeter has separate power supply. 2. Configure the rs485 port in th...

  • Page 39: Configurator

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 39 9. Configurator configurator is a pc program, which allows: configuring the terminal via graphic interface and with the help of commands; troubleshooting the terminal saving the results in a log-file; seeing the terminal units st...

  • Page 40: 9.2 Device Tab

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 40 9.2 device tab the tab displays the information about the terminal state and allows its resetting. This tab contains the terminal model, oriented in space according to accelerometer indications. The model can be rotated by mouse....

  • Page 41

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 41 after successful authorization on the server, the form of terminals list management will become available. When connecting for the first time, the list of the controlled terminals will be empty. To add a terminal to the list, cli...

  • Page 42: 9.3 Troubleshooting Tab

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 42 9.3 troubleshooting tab this tab allows us to see the current terminal state through the troubleshooting reports. The troubleshooting mode has the following buttons: 1) start /stop the time scale displays the information about th...

  • Page 43

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 43 gprs. Not activate. Gprs initialization failed. Gprs is not activated on this sim card. Not enough money on the account. Gsm network is overloaded. Gprs. Success connect to server. Device server connection is successful gprs. Not...

  • Page 44

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 44 sat. Valid = 1 coordinates are right (they can be used for location determination). This valid is not related to valid in packet and status. Galileo uses glonass terminal uses glonass system. Galileo uses gps terminal uses gps sy...

  • Page 45: 9.4 Command Mode Tab

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 45 9.4 command mode tab this tab is intended to message a single command or a set of commands to the terminal. The command mode has the following buttons: 1) run commands; 2) run single command; 3) open from file; 4) save to file. T...

  • Page 46

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 46 set of commands example enter the necessary commands in commands window, each beginning a new line, as shown in the figure below and press the run commands button. Example: serverip 55,34,76,123,30100 id 6299 headpack 1110 the gi...

  • Page 47

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 47 example of saving and downloading parameters set for quick configuration of several terminals with the same set of commands it is recommended to run the commands from a pre-saved file. To do this, enter a list of commands in the ...

  • Page 48

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 48 9.5 graphic interface settings all main settings of the terminal are placed on tabs in the program upper part. 9.5.1 security this tab allows setting sim-cards pin code, phone authorization password, list of authorized phone numb...

  • Page 49

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 49 9.5.3 protocol the terminal has its own data transmission protocol developed by galileosky ltd. During device operating and data sending to the server, the following stages are possible: 1) initialization of tcp/ip connection (do...

  • Page 50

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 50 9.5.4 power saving this tab allows setting shutdown options of the terminal units at stop, to reduce power consumption. 9.5.5 track this tab allows setting archive storage place and recording periods of coordinates at stops and i...

  • Page 51

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 51.

  • Page 52

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 52 9.5.6 inputs/outputs for inputs operating principles see section discrete-analog inputs (dai). For discrete outputs description see section transistor outputs (0/1)..

  • Page 53

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 53 9.5.7 digital inputs this option allows choosing the type of peripheral connected to rs232 inputs, setting ibutton keys, setting up periodical camera shooting. 9.5.8 sound this option allows setting a microphone and sound gain vi...

  • Page 54

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 54 9.5.9 signaling this option allows setting the response of the terminal to inputs state change, speed and coordinate change. You can set telephone numbers for sms or call in case of signaling activation. Strike and incline determ...

  • Page 55

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 55 9.5.11 geofences on this tab it is possible to set the list of geofences and behavior of the terminal inside and outside them..

  • Page 56

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 56 9.6 data loading and sending to server 9.6.1 data loading from the terminal to file this option allows transferring the data from the internal memory or an sd-card to computer files via a usb cable. By data loading from the inter...

  • Page 57

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 57 9.7 routes for autoinformer this tab contains a graphical autoinformer zones editor (section autoinformer function ). The internet access is required to display the map. To edit the zones: 1) insert a micro-sd card into the compu...

  • Page 58: 9.8 Trusted Ibutton Keys

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 58 9.8 trusted ibutton keys this tab contains the editor of a trusted ibutton keys list. The list is stored on a microsd-card; to edit the list, perform the following: 1. Eject the microsd-card from the terminal. 2. Insert the micro...

  • Page 59: 10.

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 59 10. Commands list to request current settings you need to issue a command without any parameters. 10.1 settings for sms control command format addphone xxxx[,n] parameters xxxx - is a four-digit password, 1234 by default n – slot...

  • Page 60

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 60 command format ops02 n16,n17,n18,n19,n20,n21,n22,n23,n24,n25,n26,n27,n28,n29,n30 parameters n16-n30 – preferred gsm-networks. Explanation additional list of preferred gsm-networks for sim0. Example request: ops02 25001,25099 repl...

  • Page 61

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 61 command format id n parameters n - terminal number explanation changes terminal number. The same number is used as the device identifier in the egts protocol. Example request: id 123 reply: id=123 command format roaming mcc_mnc,s...

  • Page 62

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 62 10.3 server exchange protocol settings command format headpack bbbbbbbbbbbbbb parameters bbbbbbbbbbbbbb - tag set from 1 to 128. If b is replaced by 1, the tag is on. If b is replaced by 0, the tag is off. Tag numeration order is...

  • Page 63

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 63 this means that tags 129, 130, 131, 132 are off and tags 133 and 134 are on. All the following tags are off. Command format mainpackbit index,value parameters index –tag number, which is on or off for transmission to the server v...

  • Page 64

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 64 10.4 track parameters setting command format turning v,a,d,s,ds parameters v – minimum speed that enables drawing of the track on the corners, [km/h]; a – minimum turn angle for the terminal to record a track point, [º]; d – the ...

  • Page 65

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 65 command format accsens sens,to parameters sens – accelerometer sensitivity. To – the time after the vehicle stops, during which coordinates are updated, [sec]. Explanation this function allows avoiding unnecessary outliers after ...

  • Page 66: 10.5 Geofences Settings

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 66 10.5 geofences settings command format dzone mode parameters mode – operation mode inside a geofence: 0 – geofence processing is switched off; 1 – coordinates updating prohibition inside a geofence; 2 – gsm/3g-unit switching off ...

  • Page 67: 10.6 Information Commands

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 67 10.6 information commands command format status explanation allows receiving device status at the moment of sending a command. Dev – this device number; soft – current firmware version; pack – last recorded packet serial number; ...

  • Page 68

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 68 command format temex0 explanation allows finding temperature from the first four external ds18s20 thermometers. Format: the lower byte is the thermometer identifier; the higher byte is the temperature itself. To calculate the tem...

  • Page 69: 10.7 Service Commands

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 69 command format lastcmd n parameters n- number of recorded command, beginning from 0 explanation allows overlooking the archive of the last executed commands. Returns the command source, time, date and text of the command. Example...

  • Page 70

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 70 reply: erasetracksd command format coldstart explanation glonass unit cold start. Example request: glonasscoldstart reply: glonass cold start command format reset explanation allows resetting the device remotely. Example request:...

  • Page 71

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 71 10.8 voice communication settings command format gsmvolume k,m parameters k – gsm-channel sound gain [1÷100]. M – gsm-channel microphone gain [1÷15]. The greater the parameter, the greater the gain. Explanation allows speakerphon...

  • Page 72

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 72 10.9 analog-discrete inputs setting command format incfg_num_in ft,fl,up_low,up_hi,down_low,down_hi,imp_null parameters num_in – an input number, beginning from 0; ft – filter type 0 – mean value computation; 1 – pulse count; 2 –...

  • Page 73: 10.11 Autoinformer Setting

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 73 10.10 transistor outputs setting command format out v,s parameters v – output ordinal number (starting with the zero output); s – desired state (0 – on-state transistor output; 1 –off-state transistor output). Explanation transis...

  • Page 74

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 74 command format dfilter rs2320 parameters rs2320 – filter length for a fuel level sensor connected to the zero rs232 port, the number of successive sensor indications, which are averaged. If the value is equal to 1, there is no fi...

  • Page 75

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 75 command format cub5 n0,0 parameters n0 – parameter number displayed on the indicator connected to rs232 port. Parameters: 0 – speed, accurate within 0.1, [km/h]; 1 – directional angle accurate within 0.1 [°]; 2 – external supply ...

  • Page 76

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 76 command format addkey key1,…,key25 parameters key – the lower 4 bytes of the ibutton identification number excluding the checksum in hexadecimal form. For example, the full key number in hexadecimal form is: 09 00 00 00 91 02 0c ...

  • Page 77

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 77 10.13 signaling mode setting command format sign gwtime,dropalarmtimeout,useib parameters gwtime – duration of the "green wave" which is the time after the signalling starts, during which no sampling of sensors takes place, [sec]...

  • Page 78

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 78 command format sin0 type,delay,sms,ring,photo,msg parameters type – an input mode: 0 – is not used for signaling; 1 – input activation results in signaling mode on; 2 – input activation results in alert mode on if signaling mode ...

  • Page 79

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 79 command format sout0 emode,elmpt,elmpc,dmode,dlmpt,dlmpc,amode,almpt,almpc,adelay parameters emode – output operating mode by arming: 0 – no reaction, 1 – output is inverted, 2 – output generates pulses, elmpt – pulse time during...

  • Page 80: 10.14 Can Settings

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 80 10.14 can settings command format canregime mode,baudrate,timeout, donotcleanaftertimeout parameters mode – operating mode: 0 – can-interface is off and is not used; 1 – can-bus scanner; 2 – standard fms filter; 3 – user filter29...

  • Page 81: 11.

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 81 11. Bootloader the processor program (firmware) is a set of algorithms developed by galileosky ltd specialists. Owing to this program, the central processor receives the data from different system units, processes them logically ...

  • Page 82: 12.

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 82 12. Server exchange protocol this protocol supports bi-directional data exchange between the terminal and the server. The data are transmitted via gprs channel with the use of tcp/ip protocol. The server must have static address ...

  • Page 83

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 83 main pack structure is the same as the structure of the head pack. Transmitted tags are set by mainpack command. Main pack may transmit several records from the archive. First record tags go first, then the second record tag and ...

  • Page 84

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 84 № tag number designation parameter length, byte format 12 0x41 supply voltage, mv 2 unsigned integer. 13 0x42 battery voltage, mv 2 unsigned integer. 14 0x43 terminal temperature, c 1 signed integer. 15 0x44 acceleration 4 10 low...

  • Page 85

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 85 № tag number designation parameter length, byte format 32 0x90 first ibutton key identification number 4 33 0xc0 can-bus and can-log data (can_a0). Fuel used by a vehicle from the date of manufacturing, l 4 unsigned integer, the ...

  • Page 86

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 86 № tag number designation parameter length, byte format 56 0xd7 depending on settings: 1. Can16bitr1 2. The 2 nd vehicle`s axle load, kg 3. Failure code obd ΙΙ 2 in case the load is on axle, the value is an unsigned integer; value...

  • Page 87

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 87 № tag number designation parameter length, byte format 69 0x80 zero ds1923 sensor identifier, measured temperature ºc and humidity %. 3 lower byte: unsigned integer, identifier. The second byte: integer, temperature. Higher byte:...

  • Page 88

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 88 № tag number designation parameter length, byte format 97 0x8c temperature from fuel level sensors connected to rs485 port with address 2, С 1 signed integer 129 0xa0 can8bitr15 1 accessible only by a dynamic archive structure ta...

  • Page 89

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 89 № tag number designation parameter length, byte format 176 0x5d ДБГ-С11Д dosimeter data 3 2 lower bytes: ader, 3v/h, unsigned integer, (xxxxxxyy yyyyyyyy – x-order, y – floating-point coefficient). Higher byte: dosimeter state. B...

  • Page 90

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 90 3- euroscan 2-3 0 1 2 3 4 5 6 7 8 9 10 11 12 status (flags): -no connection with the unit -zone 1 unit is on -zone 2 unit is on -zone 3 unit is on -temperature recorder 1 is available -temperature recorder 2 is available -tempera...

  • Page 91

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 91 9 2 3 4-7 -defrost mode is on -door is open -alarm type (0-no alarm) -alarm code 10 bytes zone 2 data (see zone 1 data) 10 bytes zone 3 data (see zone 1 data) 2 bytes temperature recorder 1 value [signed integer, accurate to 0,1 ...

  • Page 92

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 92 example1. The terminal should be configured so that the head pack (headpack) contains information about the terminal`s version (hardversion), firmware version (softversion), unique 15-digit gsm/3g-unit identifier (imei), terminal...

  • Page 93: Additional Information

    Galileosky glonass/gps v5.1 (223) user’s manual galileosky ltd page 93 13. Additional information 1. Certifying the terminal is certified to comply with gost r. 2. Warranty galileosky ltd hereby guarantees the realization of consumers’ rights provided by the local laws throughout russia and the cis....