Gallien-Krueger Neo series Owner's Manual - page 4
Neo Series Bass Enclosures
Owner’s Manual
Part # 160-0340-B
Specifications
Neo 410
Neo 210
Neo 115
Neo 412
Neo212
Neo 112
Impedance:
8 ohms
8 ohms
8 ohms
4 ohms
8 ohms
8 ohms
Power Handling (RMS):
800W
400W
500W
1200W
600W
300W
Power Handling (Peak):
1600W
800W
1000W
2400W
1200W
600W
Sensitivity:
103 dB
98 dB
99 dB
102 dB
101 dB
98 dB
Maximum SPL:
132 dB
124 dB
127 dB
133 dB
129 dB
122 dB
Frequency Resp. (-3dB):
30 Hz to 19 kHz
47 Hz to 19 kHz
45 Hz to 19 kHz
54 Hz to 19 kHz
53 Hz to 19 kHz
51 Hz to 19 kHz
Woofers (Neodymium):
200W 32 ohm
200W 16 ohm
500W 8 ohm
300W 16 0hm
300W 16 ohm
300W 8 ohm
Horn (P-Audio):
25W 8 ohm
25W 8 ohm
25W 8 ohm
25W 8 ohm
25W 8 ohm
25W 8 ohm
Porting:
Front-Ported
Front-Ported
Front-Ported
Front-Ported
Front-Ported
Front-Ported
Dimensions (WxHxD):
23.5 x 26.5 x 18.5
23.5 x 19.5 x 18.5
23.5 x 26.5 x 18.5
23.5 x 40 x 17.5
21 x 26.5 x 16.5
21 x 26.5 x 16.5
Weight:
78 lbs.
45 lbs.
63.5 lbs.
118 lbs.
60 lbs.
37 lbs.
Weight:
Weight:
Tech Talk
Impedance Guidelines: The impedance of your speaker
enclosure is referred to as the Ohm rating. Amplifi ers
connect cabinets in parallel so when combining speaker
enclosures, the impedance or Ohm rating will go down.
8 Ohms + 8 Ohms = 4 Ohms
4 Ohms + 4 Ohms = 2 Ohms
4 Ohms + 8 Ohms = 2.67 Ohms
Note: If you are combining speaker enclosures of
different impedances, the enclosure with the lower
impedance will receive a greater amount of the signal
causing it to be louder than the other cabinet.
Horn Bi-Amp System:
The Neo Series cabinets include a passive crossover for
standard operation or may be used with GK’s unique Horn
Bi-Amp System.
Horn Bi-Amp compatible amplifi ers use an electronic crossover
to split the signal between the main amplifi er and a separate
horn (tweeter) amplifier. The horn amp sends signals
above 5kHz to the horn while the main amplifi er sends a
full range signal to the woofers. Optionally you can engage
the Woofer High-Cut to to cut signals above 5kHZ from the
main amplifi er. Both signals are delivered to the cabinet via
a single
Speakon® cable.
Note: The 50W horn amplifi er has a fi xed frequency
output of 5kHz and up (high frequencies only). It
will not provide a useable signal to drive a seperate
speaker cabinet.
Note: To avoid risk of damage to the equipment, do
not use a 4-conductor Speakon® cable with non GK
cabinets. Instead use a 2-conductor Speakon® or
¼” speaker cable.
CAUTION: UNDER NO CIRCUMSTANCES
SHOULD THE WOOFER/MAIN AMP AND
THE 50 WATT HORN AMP BE CONNECTED
TOGETHER!!!