1. DL manuals
  2. Gallo Tech
  3. Remote Starter
  4. GTStarter-2 GTS-2
  5. Operation & Installation Manual

Gallo Tech GTStarter-2 GTS-2 Operation & Installation Manual

Manual is about: Keyless RFID Push Button Start & Security System

Summary of GTStarter-2 GTS-2

  • Page 1

    © copyright gallo technologies. All right reserved - 1 - rev. V8.2- 20212 operation & installation manual (v8.2) keyless model # gts – 2 keyless rfid push button start & security system disclaimer: this installation manual is designed for the professional installer with a good understanding of autom...

  • Page 2: Important:

    © copyright gallo technologies. All right reserved - 2 - rev. V8.2- 20212 important: read all instructions before installation gtstarter-2 has been designed to eliminate the need for an ignition key to unlock, start and stop the vehicle, and provide a high level of security. Gtstarter-2 makes use of...

  • Page 3

    © copyright gallo technologies. All right reserved - 3 - rev. V8.2- 20212 dual voltage systems have lock/unlock switches that send varying levels of positive voltage or negative ground current to the same wire for both lock and unlock. When the vehicle’s body computer module (bcm) or door lock modul...

  • Page 4

    © copyright gallo technologies. All right reserved - 4 - rev. V8.2- 20212 m ute button: silent-(arm/disarm)/remote-lock/siren-stop a.) silent arm:  when in disarmed mode press one time, parking lights flash once, blue l.E.D. On the engine start button will flash slowly, the siren will not chirp, th...

  • Page 5

    © copyright gallo technologies. All right reserved - 5 - rev. V8.2- 20212 turning acc, ign1, ign2 on/off and starting the engine: when in disarm mode and the rfid key fob is in detection range. To turn acc on/off press “push start stop” button once then release, acc will turn on; press “push start s...

  • Page 6

    © copyright gallo technologies. All right reserved - 6 - rev. V8.2- 20212 to start / stop engine. To start engine: while pressing the brake/clutch peddle, press “push start stop” button and hold until the engine starts. Ign 1 will turn on, the starter will engage and the engine will start. After the...

  • Page 7

    © copyright gallo technologies. All right reserved - 7 - rev. V8.2- 20212 disabled: when the key fob is within range, and the system is in disarm mode, the lights will flash 2 times. The “push start stop” button is activated when the door is opened. The green led will flash slowly. The siren will no...

  • Page 8

    © copyright gallo technologies. All right reserved - 8 - rev. V8.2- 20212 10. Rfid scan time: short (default): sets the interval between the rfid transmitter scans to a shorter period of time. Normal battery life & shorter detection time. Preferred. Long: sets the interval between the rfid transmitt...

  • Page 9

    © copyright gallo technologies. All right reserved - 9 - rev. V8.2- 20212 table 1: function option chart press valet switch # of times programmable function function default lights flash 3 times function alternate light flash 1 time 1 auto door lock/unlock enabled (default) auto lock/unlock off 2 au...

  • Page 10

    © copyright gallo technologies. All right reserved - 10 - rev. V8.2- 20212 figure 1 option 1 – the user has the option of keeping the original ignition switch or completely removing it. If the ignition is kept operational, the vehicle can then be started with either the “push start/stop” button or t...

  • Page 11

    © copyright gallo technologies. All right reserved - 11 - rev. V8.2- 20212 2 pin low frequency (lf) antenna wire harness. The lf antenna is used for the rfid circuitry. The antenna must not be placed directly on any metal surface. The antenna must be mounted in a horizontal position. Plug in the 2 p...

  • Page 12

    © copyright gallo technologies. All right reserved - 12 - rev. V8.2- 20212 figure 3 figure 4 figure 5 figure 6.

  • Page 13

    © copyright gallo technologies. All right reserved - 13 - rev. V8.2- 20212 2 pin wire harness ( control module power, parking lights) c4: red 15 amp fused wire – + 12v constant battery input (control module supply power). This connection should have constant +12v available (bat terminal on ignition ...

  • Page 14

    © copyright gallo technologies. All right reserved - 14 - rev. V8.2- 20212 for manual transmission: connect the yellow wire to a clutch peddle switch that has a neg. (-) output when the clutch peddle is depressed. Then change function option #2 to manual transmission. C7: green – neg (-) disarm outp...

  • Page 15

    © copyright gallo technologies. All right reserved - 15 - rev. V8.2- 20212 engine cranks but will not start: 1. Check ignition switch wiring. See sec. 1.6 “installing connector c1. Some vehicles require 2 separate ignition wires ign 1 and ign 2 for the vehicle’s ignition system to function properly....