1. DL manuals
  2. Galls
  3. Amplifier
  4. ST160 SIREN
  5. Installation And Operating Instructions Manual

Galls ST160 SIREN Installation And Operating Instructions Manual

Manual is about: Siren Amplifier

Summary of ST160 SIREN

  • Page 1

    Plitstr312 rev. D 10/28/13 siren siren siren siren installation and operating instructions installation and operating instructions installation and operating instructions installation and operating instructions st240 st240 st240 st240 street thunder street thunder street thunder street thunder ™ ™ ™...

  • Page 2

    -i- installation information model: st240 serial #: purchase date: installation date: installer: dealer: model and serial number located on bottom of unit table of contents general description 1 installation notes 1 mounting tips 1 electrical connections 2-3 wiring guide 2 wiring diagram 2 mandatory...

  • Page 3

    -1- installation notes the st240 siren amplifier is a premium 200w unit designed for dual 100w speaker use. The primary operating modes are thunder, yelp, wail, hands free, manual, pa, and radio. A noise canceling pa override and push-button horn override are available in all modes. A manual push-bu...

  • Page 4

    -2- wire size and termination electrical connections to this unit are made through the green 12-terminal connector located in the rear of the unit (see below - part # cpss-153). Examine the charts below to determine the proper gauge of the wire to use. Please review the following recommendations whe...

  • Page 5

    -3- (electrical connections cont’d) for ease of installation, you can remove the green connector from the siren while connecting your wires. Please note that when referencing terminal numbers using the wiring diagram on the previous page, the siren should be held upside down so the screw heads face ...

  • Page 6

    -4- the st240 has several options that can be selected prior to installation by using either the two dip switches located on the back of the unit, or by using the “tone programming” button on the back in combination with the knob and/or buttons on the front of the unit. These options should be set b...

  • Page 7

    -5- 1 wail (wail default) §, *, † 2 yelp (yelp default) §, * 3 thunder (thunder default) 4 two-tone (thunder step up default) 5 mechanical wail (fire engine) † 7 hoot 8 rapid hoot 9 air horn & yelp 10 ghost 11 rapid ghost 12 single air horn 13 single quick 14 double post pop air horn 15 two tone air...

  • Page 8

    -6- operation general this unit is designed for easy operation under the stress associated with high-speed pursuit. Most siren functions are accessible with one simple motion without repetitive activation of switches or automatic timed switching that can interfere with desired operation. Power/pa kn...

  • Page 9

    -7- (operation cont’d) manual rotary switch position function when manual pressed manual or hf produces a rising siren tone while being pressed. The siren output “winds down” when the manual button is released. Pa also produces a rising tone, but the siren output immediately stops when the button is...

  • Page 10

    -8- speaker diagnostics there is a diagnostic led shaped like a speaker located in the upper right hand corner of the front panel. This led will only turn on while a tone is trying to be generated. It can be used to help identify the siren/speaker status. Steady - speaker is connected and operating ...

  • Page 11

    -9- parts service part description s30161-18 siren top extrusion p30234-11-1p siren bottom mounting plate swh-152 optional wiring harness p30069-38 microphone bracket with screws p30056-16 1/4-20 x 3/8" hex locking bolt p30028-23 20 amp automotive fuse p30232-1 noise cancelling microphone p30208-10 ...

  • Page 12

    No hassle guarantee providing quality products to professionals who protect and serve the public is our core purpose. If you aren’t satisfied with a newly purchased item, simply return it to us so we can repair it, replace it or refund your money. To return merchandise… within the first 60 days: ple...