Owner's manual issue 6 - march 2007 stringing machine 5003 6 point mounting.
1 limited warranty gamma sports ("gamma") warrants to the original purchaser that the gamma 5003 stringing machine ("equipment") purchased is free from defects in materials and workmanship for a period of five (5) years from the date of original purchase for mechanical parts (excluding string clamps...
2 features 1 - diamond coated “quick action” metal string clamps 2 - manual spring tensioner 3 - diamond coated linear string gripper 4 - tension range: 11lbs. - 89lbs. 5 - 6 point mounting system 6 - full 360 degree turntable rotation 7 - large convenient 141 sq. In. Tool tray 8 - height adjustable...
3 carton one contents: (1) upper support post (1) lower support post w/ plate (1) long leg w/ adjustment foot (3) short legs w/ adjustment feet (4) m8 x 30 cap screws (4) m8 x 25 flat head screws (1) bellows set (1) tool tray w/ pad (1) winged turntable locking knob screw (1) tensioner assembly (1) ...
4 assembly instructions base leg assembly the stringing machine uses a four leg base design. The legs must be assembled to the support post before use. Remove the lower column support from the carton. This is the larger of the two posts and has the gamma label. Note: for illustration purposes, the s...
5 bellows installation the bellows assembly is supplied in two pieces and should be assembled as follows. Place the bellows section with the flange over the upper support column with the flange on the top. Place the remaining bel- lows over the upper support column and mate it with the flange on the...
6 assembly instructions turntable and mounting system in- stallation to install the turntable remove the four nuts underneath holding the mounting bolts in place. Align the bolts with the holes in the turntable pin. Secure them with the included allen wrech. Note: applying the turntable brake will m...
7 assembly instructions setting the gripper jaw spacing the gripper jaws of the tensioner are adjust- able to accomodate varying string gauges. If the string slips through the gripper jaws while pulling tension, rotate the gripper jaw adjustment screw counter-clockwise. If the string is damaged whil...
8 mounting the frame adjusting the frame shoulder sup- ports being sure the shoulder supports are free to swivel in their mountings, simultaneously rotate the shoulder support adjustment knobs clockwise until both shoulder supports gen- tly and squarely contact the frame. Securing the frame lock the...
9 setting tension the tensioner utilizes a rotary adjusting knob along with a linear tension scale to indicate the tension setting. The scale is divided into 3 lb increments and each 1/3 turn of the tension knob changes tension by 1 lb. To set the desired tension, rotate the tension knob and align t...
10 stringing the frame pulling tension wrap the loose section of string once around the roller guide and insert the string between the diamoind dust coated string gripper plates. Pull the string perpendicular to the gripper plates while slowly rotating the tensioner crank clockwise until the brake l...
11 stringing the frame weaving the cross strings weave the cross strings over and under the main strings being careful to alternate the weave direction of each consecutive cross string so as to be opposite of the previously installed cross string. Once the final cross string is tensioned and clamped...
12 tension calibration step 2 loosen the 1.5 mm locking set screw (a) located on the side of the latching block as shown. The set screw is used to hold the adjustment screw in place. Step 3 if the lever releases before 60 lbs., using the supplied l-shaped hex wrench, turn the ad- justment screw (b) ...
13 a - cover screws b - lock bolt a b a adjusting the tensioner brake step 1 after stringing many racquets, the brake of the tensioner may need to be adjusted. The brake adjustment bolt can be accessed through the hole in the face of the tensioner cover, which does not need to be removed for adjustm...
Pathfinder awl operation the machine includes the pathfinder string- ing awl which creates a pathway between or around strings and through tight grom- mets. Insert the awl through the grommet hole in the same manner as for traditional awls. The pathfinder awl must be closed before inser- tion. Once ...
15 troubleshooting tips problem solution string slips in clamps string slips in gripper string tension too tight or too loose for additional assistance, contact gamma sports customer service at 1-800-333-0337 - adjust gap between jaws - clean clamp jaws - clean gripper jaws - adjust gripper jaw stop...
16 mounting stand parts part # 9 21a 140 141 142 143 144 145 146 147 148 description m8 bolt frame support slide mtng. Stand top plate mtng. Stand pad support arm - left support arm - right shlder supp. Lock knob supp. Arm return spring arm adjustment knob arm adjustment screw shoulder v-clamp (l or...
17 machine parts 111 117 104 112 113 115 114 120a 106 282 289 mdcsc 119 105 116a 6b 121 mqac.
18 description cap screw - m8 x 30 tensioner assembly retainer screw table brake knob tensioner track tool tray long leg short leg flat head screw - m8 lower column supp. Tensioner cover bellows upper column supp. Leveling foot turntable tt handle qa clmp base tall string clamp pathfinder awl string...
Gamma sports 200 waterfront drive pittsburgh, pennsylvania 15222 phone : 800-333-0337 fax : 412-323-0317 visit our website at www.Gammasports.Com.