1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. Progression 200
  5. Owner's Manual

Gamma Progression 200 Owner's Manual - Assembly Instructions

Summary of Progression 200

  • Page 1

    Owner’s manual issue 1a - december 2012 200 stringing machine.

  • Page 2: 200

    2 200 mp200-10 owner’s manual limited lifetime warranty gamma sports (gamma) warrants to the original purchaser that the progression 200 stringing machine (“equipment”) purchased is free from defects in materials and workmanship for life of the equipment. Should any defects develop under normal use,...

  • Page 3: Features

    3 features machine features  drop weight tensioner w/ 9 to 90lb range and permanently engraved weight scale  patented parallel jaw rotating ratchet gripper w/ diamond dust coated gripping surfaces  two point racquet mounting system- accommodates all racquets  two advanced composite floating clam...

  • Page 4: Assembly Instructions

    4 assembly instructions installing the turntable insert the turntable center post into the bush- ing assembly of the machine base. Installing the support posts slide each support post onto the end of the turntable bar. The posts should be oriented so as to angle away from the turntable center post. ...

  • Page 5: Assembly Instructions

    5 assembly instructions tension bar stop screw raise the tension bar to an upright position. Using the supplied 5mm wrench, securely tighten the stop screw. This will prevent the tension bar from contacting the racquet frame..

  • Page 6: Mounting The Racquet

    6 adjusting the frame support posts place the racquet frame over the center posts and onto the frame support posts. Loosen the locking screws on one support post and slide the post in the appropriate direction until the plastic adapter contacts the frame. Securely tighten the locking screws. Adjust ...

  • Page 7: Stringing The Frame

    7 stringing the frame setting tension the drop weight is of a two piece design. When assembled, it will accommodate ten- sions from 20 to 90 lbs. For tensions from 8 to 20 lbs., remove the 5mm bolt on the face of the drop weight, and use the smaller portion of the weight as described above. Note: te...

  • Page 8: Stringing The Frame

    8 stringing the frame clamping the first main string thread one end of the string through the adjacent grommet hole and pull excess by hand. Clamp both the center and the adjacent string to each other on the inside of the frame. Pulling tension wrap the free string clockwise around the gripper drum ...

  • Page 9: Stringing The Frame

    9 stringing the frame clamping the string clamp the tensioned string to the next ad- jacent string using the second string clamp. Release the tensioned string by raising the tension arm. Repeat the procedure for all of the remaining main strings and tie off following the racquet manufacturers recomm...

  • Page 10: Pathfinder Awl

    10 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in the grommet hole. Insert the end of the string into the outer sheath. While holding the string, slowly pull the sheath out of the grommet hole to lea...

  • Page 11

    11 maintenance & adjustments clamp adjustment the fl oating clamps provided with your ma- chine will need minor adjustments according to what string type, construction, and gauge you are using. If the strings slip through the jaws of the clamp, tighten the clamp by turning the thumb knob opposite of...

  • Page 12: Care & Cleaning

    12 care & cleaning with time and use, the clamping surfaces of your machine may become oily or dirty and result in string or clamp slippage while stringing. Periodic cleaning of the string clamps and string gripper is recommended. Knife sharpening stones work well for cleaning the diamond coated str...

  • Page 13: Notes

    13 notes.

  • Page 14: Parts  List

    14 parts list 4a turntable bushing 5 rubber foot 6a cap screw- m8x25 8a set screw- m5x6 24 knob 25 tension bar 26 tension bar cap 27 drop weight knob 28 front weight- badminton 29 back weight 30 tension bar drum 30a set screw 31 string gripper drum 47 floating clamp knob 48 swing bolt 49 return spri...

  • Page 15: Parts Drawing

    15 parts drawing 316 mrsg 82a 5 350 4a 29 28 27 25 mpfc 31 49 51 47 50 48 94 82 92 95 93 24 79 78 26 30a 83a 30 8a 6a 162 163 161 258 257 315.

  • Page 16: Gamma Sports

    Gamma sports 200 waterfront drive pittsburgh, pennsylvania 15222 phone: 800.333.0337 fax: 412.323.0317 visit our website at www.Gammasports.Com copyright 2010 gamma sports - all rights reserved mman-14.