1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. PROGRESSION 602
  5. Owner's Manual

Gamma PROGRESSION 602 Owner's Manual

Other manuals for PROGRESSION 602: Owner's Manual

Summary of PROGRESSION 602

  • Page 1

    Owner's manual issue 5 - november 2012 602 stringing machine.

  • Page 2

    2.

  • Page 3: Limited Warranty

    3 limited warranty gamma sports ("gamma") warrants to the original purchaser that the gamma progression stringing machine ("equipment") purchased is free from defects in materials and workmanship for a period of fi ve (5) years from the date of original purchase for mechanical parts (excluding elect...

  • Page 4: Features

    4 features machine features  drop weight tensioner with 9 to 90 lbs range and permanently engraved weight scale patented parallel jaw rotating ratchet gripper with diamond dust coated gripping surfaces professional six point “quick mount” racquet mounting system- accommodates all racquets two compo...

  • Page 5: Assembly Instructions

    5 assembly instructions engaging the drop weight bar stop the stringing machine is shipped with the drop weight bar in the horizontal position. To prevent racquet damage during stringing, the bar stop must be engaged. Remove the machine base from the shipping carton being careful to avoid lifting by...

  • Page 6: Mounting The Frame

    6 securing the frame lock the shoulder supports in position by turning the knob at the base clockwise. Repeat the adjustment procedure for the remaining support post. Re-tighten all of the frame supports in the same order as before. Do not overtighten any of the supports as racquet damage may occur....

  • Page 7: Stringing The Frame

    7 stringing the frame the drop weight is of a two piece design. When assembled, it will accommodate ten- sions from 20 to 90 lbs. For tensions from 8 to 20 lbs., remove the 5mm bolt on the face of the drop weight, and use the smaller portion of the weight as described above. Note: tensions above 77l...

  • Page 8: Stringing The Frame

    8 stringing the frame gripping the string while holding the tension bar slightly above horizontal, wrap the free string clockwise around the gripper drum once and position between the gripper jaw. Gently turn the gripper clockwise while squeezing the jaws together until all slack in the string is re...

  • Page 9: Stringing The Frame

    9 stringing the frame clamping the first main string secure the tensioned main string using the remaining fi xed clamp. Repeat the procedure for all of the remaining main strings and tie off following the racquet manufacturers recommendations. Follow the manufacturer's recommended stringing pattern ...

  • Page 10: Additional  Features

    10 additional features badminton shoulder support protec- tion pad installation slide the badminton shoulder support cover over the shoulder supports. There is no need to remove the tennis shoulder supports. Note: an optional badminton frame support for the head of the racquet is available..

  • Page 11: Pathfinder Awl

    11 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in the grommet hole. Insert the end of the string into the outer sheath. While holding the string, slowly pull the sheath out of the grommet hole to lea...

  • Page 12

    12 adjusting the clamp pressure the clamps provided with your stringing ma- chine will need minor adjustments according to what string type, construction, and gauge you are using. To adjust the gap (clamping pressure) between the clamp jaws, insert the string through the racquet as if you were begin...

  • Page 13: Care & Cleaning

    13 care & cleaning with time and use, the clamping surfaces of your machine may become oily or dirty and result in string or clamp slippage while stringing. Periodic cleaning of the string clamps, string clamp base and string gripper is recommended. Knife sharpening stones work well for cleaning the...

  • Page 14: Parts List

    14 mbfs11 badm frame support mbmss11 badm mounting sys upg mbfc badm floating clamp mdcsc badm fixed clamp mpg starting clamp mpmc machine cover mps cleaning stone mpxfs floor stand sgsm stringer’s mat parts list 4a turntable bushing 5 rubber foot 6a cap screw 8 bushing set screw 9 washer- m8 10b wi...

  • Page 15: Parts Drawing

    15 sb sq t b parts drawing 5 261 14 mmspp13 133 21a 189 187 188 4a 8 9 6a 9 6a 190 144 356 140 357 141 146a 271 10b mfspp11 mrsg 29 28 27 25 26 31 30a 83 30 162 163 161 35 34 262 mpfc mbmsp11 381.

  • Page 16: Gamma Sports

    Gamma sports 200 waterfront drive pittsburgh, pennsylvania 15222 phone : 800.333.0337 fax : 412.323.0317 visit our website at www.Gammasports.Com copyright 2012 gamma sports - all rights reserved mman-33 (mp602-12).