1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. Progression ES II+
  5. Owner's Manual

Gamma Progression ES II+ Owner's Manual

Other manuals for Progression ES II+: Owner's Manual

Summary of Progression ES II+

  • Page 1

    Stringing ma stringing ma stringing ma stringing ma stringing machine chine chine chine chine owner's manual issue 1 - january 2000 copyright 2000 gamma sports - all rights reserved.

  • Page 2

    1 limited warranty limited warranty limited warranty limited warranty limited warranty gamma sports (gamma) warrants to the original purchaser that the progression stringing machine ("equipment") purchased is free from defects in materials and workmanship for a period of five (5) years from the date...

  • Page 3: Machine Features

    2 machine features electric constant pull tensioner w/ 11lb. To 89lb. Tension range digital tension setting display professional six point “quick mount” racquet mounting system - accomodates all racquets without adapters parallel jaw rotating gripper w/ diamond dust coated gripping surfaces professi...

  • Page 4: Assembly Instructions

    3 assembly instructions turntable installation insert the turntable center post into the bushing of the stringing machine base. Frame support post installation the esii support post assemblies are precision aligned at the factory and are marked for proper installation on the turntable. Install the s...

  • Page 5: Mounting The Frame

    4 mounting the frame adjusting the frame support posts place the racquet frame over the center posts and onto the frame support. Loosen the lever lock bolt on one support post. Slide the post outward until the center support of the racquet support slide is positioned near the inside surface of the r...

  • Page 6: Mounting The Frame

    5 mounting the frame securing the frame shoulder clamps lock the shoulder supports in position by turning the knob at the base clockwise. Repeat the adjustment procedure for the remaining support post. Re-tighten all of the frame supports in the same order as before. Do not overtighten any of the su...

  • Page 7: Tensioner Controls

    6 tensioner controls front panel features a - string gripper b - tension switch c - l.E.D. Tension display d - tension adjustment knob e - cover plate f - gripper reversing switch rear panel features a - lighted power switch to turn the power on, press the left side of the switch. B - 5 amp fuse hol...

  • Page 8: Stringing The Frame

    7 stringing the frame clamp base operation rotate the base locking lever clockwise to secure the clamp base to the turntable. Reverse the clamping procedure to unlock the string clamp. The locking lever is spring loaded to assist the unlocking of the clamp base. The locking lever should be tightened...

  • Page 9: Stringing The Frame

    8 pulling tension to pull tension, wrap the free string clockwise around the gripper drum and position the string between the gripper jaws. The string must pass over the top half of the gripper before being placed between the gripper jaws, as the tension on the string provides the clamping force to ...

  • Page 10: Stringing The Frame

    9 clamping the first main string secure the tensioned main string using the remaining fixed clamp. Repeat the procedure for all of the remaining main strings and tie off following the racquet manufacturers recommenda- tions. Follow the manufacturer's recommended stringing pattern for one or two piec...

  • Page 11: Pathfinder Awl

    10 10 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place, leaving the outer sheath in the grommet hole. Insert the end of the string into the center of the sheath. While holding pressure on the string, slowly pull the sheath out of the ...

  • Page 12: Maintenance and Adjustments

    11 maintenance and adjustments clamp base locking nut adjustment in the event the locking lever rotation is insufficient to ensure smooth operation of the clamp base, very minor adjustments to the clamp base locking nut can be made with the supplied 17mm wrench. Tighten or loosen the locking nut in ...

  • Page 13: Maintenance and Adjustments

    12 tension calibration procedure if you suspect that your progression esii is not pulling the correct tension, you should check the tension with a tension calibrator which provides a measurement of the actual pulling tension being applied by the machine. With the machine set for the fast pulling spe...

  • Page 14: Troubleshooting Tips

    13 troubleshooting tips fuse replacement to change the fuse, remove the power cord and pull the fuse holder straight out. Remove the old fuse from the holder and replace it with the supplied spare. Replace the fuse holder into the machine and check for proper operation. Care and cleaning with time a...

  • Page 15: Parts List

    14 parts list part # 4 5 6 7 8 9 13 14 15a 21 22 23 24 246 36 37 101 102 103 122 244 140 141 142 143 144 description turntable bushing rubber feet cap screw foot nut bushing set screw washer - m8 post lock lever washer - m10 2021 support post frame support slide badminton adapter tennis adapter supp...

  • Page 16: Exploded Parts View

    15 exploded parts view.