1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. PROGRESSION ST
  5. Owner's Manual

Gamma PROGRESSION ST Owner's Manual

Summary of PROGRESSION ST

  • Page 1

    Copyright 1997 gamma sports - all rights reserved o o o o owner's manu wner's manu wner's manu wner's manu wner's manual al al al al issue 2 / version e - oct. 28, 1997 issue 2 / version e - oct. 28, 1997 issue 2 / version e - oct. 28, 1997 issue 2 / version e - oct. 28, 1997 issue 2 / version e - o...

  • Page 2: Limited Warranty

    1 table of contents limited warranty gamma sports ("gamma") warrants to the original purchaser that the gamma progression st stringing machine ("equipment") purchased is free from defects in materials and workmanship for a period of five (5) years from the date of original purchase for mechanical pa...

  • Page 3

    2 features professional six point mounting system - accomodates all racquets without adapters parallel jaw string gripper w/ diamond dust coated gripping surfaces professional dual action, diamond dust coated, fixed string clamps durable polystyrene base cover w/ convenient padded tool tray strong, ...

  • Page 4

    3 installing the tensioner remove the button head screw and washer located at the end of the tensioner bar with the 3 mm hex wrench provided. Slide the tensioner onto the bar, being careful to align the bar with all of the bearings and the drive gear with the gear track. Replace the set screw and wa...

  • Page 5

    4 assembly instructions installing the frame support posts the progression st support post assem- blies are precision aligned at the factory and are marked for proper installation on the turntable. Install the support post with the dot on its base to an identical dot on the turntable. Align the thre...

  • Page 6

    5 assembly instructions locking the turntable the turntable may be locked in any position. The turntable winged lock knob is packed separately in the accessory polybag. Install the lock knob into the threaded hole located on the side of the tensioner bar post. Rotate the knob clockwise to lock the t...

  • Page 7

    6 mounting the frame adjusting the frame support posts place the racquet frame over the center posts and onto the frame support. Loosen the lever lock bolt on one support post. Slide the post outward until the center support of the racquet support slide is positioned near the inside surface of the r...

  • Page 8

    7 stringing the frame setting tension the progression st utilizes a rotary adjust- ing knob along with a linear tension scale to indicate the tension setting. The scale is divided into 3 lb increments and each 1/3 turn of the tension knob changes tension by 1 lb. To set the desired tension, rotate t...

  • Page 9

    8 stringing the frame pulling tension wrap the loose section of string once around the roller guide and insert the string between the diamoind dust coated string gripper plates. Pull the string perpendicular to the gripper plates while slowly rotating the tensioner crank clockwise until the brake le...

  • Page 10

    9 stringing the frame weaving the cross strings weave the cross strings over and under the main strings being careful to alternate the weave direction of each consecutive cross string so as to be opposite of the previously installed cross string. Once the final cross string is tensioned and clamped,...

  • Page 11

    10 maintenance tension calibration procedure - step 1 set the tension to 60 lbs. As indicated by the linear scale and rotary knob. Place the string on one end of a tension calibrator into a string clamp and secure. Place string located on the other end of the calibrator into the string tensioner and...

  • Page 12

    11 maintenance adjusting the string clamps the clamps provided with your stringing ma- chine will need minor adjustments according to what string type, construction, and gauge you are using. To adjust, route the string through the racquet as if you were beginning the main strings. Clamp the strings ...

  • Page 13

    12 maintenance adjusting the tensioner brake - step 2 with the cover removed, and the brake lever engaged, loosen the lower hex bolt located on the back side of the tensioner frame with the 10 mm box wrench. Note: the hex bolt should only be loosened until loose enough to turned by hand and must not...

  • Page 14

    13 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place, leaving the outer sheath in the grommet hole. Insert the end of the string into the center of the sheath. While holding pressure on the string, slowly pull the sheath out of the gro...

  • Page 15

    14 troubleshooting tips problem solution string slips in clamps string slips in gripper string clamp winged lock knob is difficult to turn string tension too tight or too loose for additional assistance, contact gamma sports customer service at 1-800-333-0337 - adjust gap between jaws - clean clamp ...

  • Page 16

    15 st parts listing part # 1 2 3 4 5 6 7 8 9 11 12 13 14 15 17 21 22 23 24 104 105 106 107 description aluminum base base cover tray pad turntable bushing rubber feet cap screw foot nut bushing set screw washer turntable turntable pin post lock lever washer support post cap screw frame support slide...

  • Page 17

    16 exploded parts view.

  • Page 18

    Mounting stand parts 143 140 141 145 144 part # 9 13 14 15 21 22 23 24 140 description washer - m8 post locking lever washer - m10 support post frame support slide badminton adapter tennis adapter support slide knob mtng. Stand top plate part # 141 142 143 144 145 146 147 148 description mtng. Stand...

  • Page 19

    18 notes.