1. DL manuals
  2. Gamma
  3. Stringing Machines
  4. X-6FC
  5. Owner's Manual

Gamma X-6FC Owner's Manual - Mounting The Frame

Other manuals for X-6FC: Owner's Manual

Summary of X-6FC

  • Page 1

    Owner's manual issue 4 - november 2012 x-6fc stringing machine.

  • Page 2

    2.

  • Page 3: Limited Warranty

    3 limited warranty gamma sports (gamma) warrants to the original purchaser that the x-stringer stringing machine ("equipment") purchased is free from defects in materials and workmanship for a period of fi ve (5) years from the date of original purchase for mechanical parts (excluding any electrical...

  • Page 4: Machine Features

    4 machine features drop weight tensioner with 8 to 90 lbs tension range and permanently engraved weight scale professional six point “quick mount” racquet mounting system- accommodates all racquets professional “quick action” dual action, rotating, composite fixed string clamps with diamond du...

  • Page 5: Assembly Instructions

    5 assembly instructions engaging the drop weight bar stop the stringing machine is shipped with the drop weight bar in the horizontal position. To limit the rotation of the drop weight bar and prevent racquet damage during stringing, the bar stop must be engaged. Hold the drop weight bar in the vert...

  • Page 6: Assembly Instructions

    6 assembly instructions installing the frame support posts place the support post onto the central slot of the turntable. While holding the mounting plate against the inside top surface of the turntable with your fi ngers, align the hole in the support post with the hole in the mounting plate. Insta...

  • Page 7: Mounting The Frame

    7 adjusting the frame support posts loosen the lock bolts of the frame support posts and space them apart with the frame support slides separated by the approximate length of the racquet head. Although it is not required, it is good practice to center the sup- port posts on the turntable. Lock one o...

  • Page 8: Mounting The Frame

    8 frame shoulder support arm adjustment being sure the shoulder supports are free to swivel in their mountings, simultaneously rotate the shoulder support adjustment knobs clockwise until both shoulder supports gently and squarely contact the frame. Securing the frame lock the shoulder supports in p...

  • Page 9: Stringing The Frame

    9 badminton shoulder support protec- tion pad installation slide the badminton shoulder support cover over the shoulder supports. There is no need to remove the tennis shoulder supports. Note: an optional badminton frame support for the head of the racquet is available. Stringing the frame the drop ...

  • Page 10: Stringing The Frame

    10 stringing the frame base clamp operation rotate the lever lock clockwise to secure the clamp base to the turntable. Reverse the clamping procedure to unlock the string clamp. The lever should be tightened enough to prevent clamp base slippage on the turn- table, when the desired tension is placed...

  • Page 11: Stringing The Frame

    11 gripping the string while holding the tension bar slightly above horizontal, wrap the free string clockwise around the gripper drum once and position between the gripper jaw. Gently turn the gripper clockwise while squeezing the jaws together until all slack in the string is removed. Note: for pr...

  • Page 12: Stringing The Frame

    12 stringing the frame weaving the cross strings follow the manufacturer's recommended stringing pattern for one or two piece stringing. This will determine the starting point for the cross strings. If applicable, tie the fi rst cross string using an appropriate starting knot. Weave the cross string...

  • Page 13: Additional Features

    13 storage drawers there is one storage drawer located in the base of the machine. The drawer opens from the right side of the base and lock into the end cap with a spring loaded latch. To open the drawer depress the latch in the face of the drawer and slide it to the right. To close the drawer simp...

  • Page 14: Pathfinder Awl

    14 pathfinder awl once the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in the grommet hole. Insert the end of the string into the outer sheath. While holding the string, slowly pull the sheath out of the grommet hole to lea...

  • Page 15: Maintenance & Adjustments

    15 adjusting the clamps the clamps provided with your stringing machine will need minor adjustments accord- ing to string type, construction, and gauge. To adjust, route the string through the racquet as if you were beginning the main strings. Clamp the strings and pull tension. If the string slips ...

  • Page 16: Care & Cleaning

    16 care & cleaning with time and use, the clamping surfaces of your machine may become oily or dirty and result in string or clamp slippage while stringing. Periodic cleaning of the string clamps and string gripper is recommended. Knife sharpening stones work well for cleaning the diamond coated str...

  • Page 17: Notes

    17 notes.

  • Page 18: Parts List

    18 parts list 4a turntable bushing 6a cap screw 8a set screw- m5x6 9 washer 14 washer 21a frame support slide 25 tension bar 26 tension bar cap 27 drop weight knob 28 front weight- badm 29 back weight- tennis 30 tension bar drum 30a set screw 31 string gripper drum 34 ratchet teeth 35 ratchet teeth ...

  • Page 19: Parts Drawing

    19 parts drawing 256 mrsg 255 4a 29 28 27 25 mcfct 31 26 30a 83x 30 8a 162 163 161 258 257 319 259 323 259 278 265 266 288 sq sb t b mmspp 284 21a 9 6a 356 144 140 141 146a 133 14 381 357 301 261 262 271 88 35 34 mfspp11 mbmsp11 mqac11 267 268.

  • Page 20: Gamma Sports

    Gamma sports 200 waterfront drive pittsburgh, pennsylvania 15222 phone: 800.333.0337 fax: 412.323.0317 visit our website at www.Gammasports.Com copyright 2012 gamma sports - all rights reserved mman-36 (mgx6f-12).