- DL manuals
- Ganz
- Security Camera
- zn-d9024nha
- Instruction Manual
Ganz zn-d9024nha Instruction Manual
Summary of zn-d9024nha
Page 1
(us)zn-d9024ntsc.Indd 1 (us)zn-d9024ntsc.Indd 1 2009/02/27 17:14:58 2009/02/27 17:14:58.
Page 2
Eg-2 product features high resolution surveillance camera with a built-in 1/4- type ccd. Integrated varifocal lens allows for versatile application and easy instal- lation. The day and night function provides high quality color picture in the normal lighting conditions (day mode) and high sensitivit...
Page 3
Eg-3 safety precautions the installation should be made by a qualifi ed service person and should conform to all local codes. This symbol indicates that there is a possibility of death or damage to operator or others. To prevent fi re or electric shock, do not expose this product to rain or moisture...
Page 4
Eg-4 parts description removing and attaching the cover dome cover to remove : pull the cover away. To attach : insert the cover and push it gently until you hear a click. Body cover to remove : insert a fl at-bladed screwdriver into the groove between the camera body and the body cover, then twist ...
Page 5
Eg-5 installation and adjustment attaching to the surface of the ceiling or wall this section explains how to install the unit where cables are running through the interior of the ceiling or wall. When running cables on the exterior surface of the ceiling or wall, please drill holes in the ceiling o...
Page 6
Eg-6 running cables on the exterior surface of the ceiling or wall to run cables on the exterior surface of the ceiling or wall, use the following procedure to attach the camera body. 1 remove the surface mount cover from the camera body. 2 remove the section of the surface mount cover indicated in ...
Page 7
Eg-7 attaching the camera body 1 remove the surface mount cover from the camera body. 2 remove the body cover. 3 attach the camera body to the adapter ring. Please use the self-tapping screws included. Do not use any other screws. When you fi nish attaching the camera, refer to page eg-8. 3 attach t...
Page 8
Eg-8 connecting the cables connect the power cable and the lan cable. Attention check if the power supply is “off.” connecting the power supply cable. 1 connect the power cable (plug) included to the power source. In the case of 12 v dc, connect the red cable to 12 v dc and the black cable to the gn...
Page 9
Eg-9 adjusting the camera direction the camera body is set in a tri-axial mounting allowing movement in the pan, tilt, and rotational planes. 1 adjust the direction of the lens so it faces the subject. Attention using the camera in a near-horizontal position will show the camera cover on screen. For...
Page 10
Eg-10 when using zn-d9922 or zn-dn9922 adjust the focal point while attaching the dome cover so that the optical axis of the lens passes through at the center of the dome cover as shown in the drawing below. Installation and adjustment complete 1 attach the body cover. 2 turn the inner cover. Then a...
Page 11
Eg-11 specifications digital day/night model mechanical day/night model model no. Ntsc system (service monitor output) zn-d9024nha zn-d9312nha zn-d9922nha zn-dn9312nha zn-dn9922nha focal length (wide to tele) 2 mm - 4 mm 3.3 mm - 12 mm 9 mm - 22 mm 3.3 mm - 12 mm 9 mm - 22 mm max. Aperture ratio 1 :...
Page 12
Eg-12 143-1.0 digital day/night model mechanical day/night model model no. Ntsc system (service monitor output) zn-d9024nha zn-d9312nha zn-d9922nha zn-dn9312nha zn-dn9922nha alarm function input 1 line: no-voltage make contact input (3.3 v dc pull-up resistor built-in - short circuit current 0.4 ma)...