1. DL manuals
  2. GarageAce
  3. Garage Door Opener
  4. R3
  5. Installation Instructions Manual

GarageAce R3 Installation Instructions Manual - 2. Product Features

Manual is about: Roller Garage Door Opener

Summary of R3

  • Page 2: Warning:

    2 warning: it is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and opener damage. Please save these instructions for future reference..

  • Page 3

    3 table of contents 1. Safety warnings – pages 4-5 2. Product features – page 6 3. Installation instructions – pages 7-8 4. Setting and operating – page 9-15 5. Common trouble shooting – page 16-17 6. Packing list – page 18 7. Technical data – page 18 8. Final notes - page 19 9. Important informatio...

  • Page 4: 1. Safety Warnings

    4 1. Safety warnings warning — it is vital for the safety of persons to follow all instructions. Failure to comply with the following safety rules may result in serious personal injury and/or property damage. Do not operate the garage door operator unless the garage door is in full view and free fro...

  • Page 5

    5 connect the garage door operator to a properly earthed general purpose 240v mains power outlet installed by a qualified electrical contractor. The outlet (and operator) must be positioned so that it is easily accessible. Disconnect the power cord from mains power before making any repairs or remov...

  • Page 6: 2. Product Features

    6 2. Product features 1. Easy to use. Just press the remote control button or the o/s/d button on the motor to open, stop or close the roller shutter. 2. Safe and reliable remote control system featuring rolling code, low coincident code rate. 3. Electronic travel limit switch, easy to operate, stab...

  • Page 7

    7 3. Installation instructions 1. Check operation of door before beginning the installation check the operation of the door the door must be well balanced and be in a reasonable operating condition. The ideal operational effort in raising or lowering the door should not exceed a force of l0kg (22 lb...

  • Page 8

    8 please note ： the instructions for fixing the operator to the door are for right hand installations only. Installation process (fig. 3, fig. 4, and fig. 5) 1. Check that the door shaft u bolt is securely tightened on the left hand side of the door. 2. Raise the door and tie a rope around the cente...

  • Page 9: 4. Setting And Operating

    9 4. Setting and operating 2. Pb/gnd/pe/+24v terminal 4. Battery backup terminal 6. K button (same function as o/s/c button) 1. O/s/c button 3. Manual release lever 5. Programming panel h. Hole for battery backup connection wires.

  • Page 10: Issues.

    10 4.1 left/right installation setting warning ： this step must be completed prior to setting travel limits (4.2) if utilizing a lift sided installation. If utilizing the standard right sided installation this step can be ignored. Press ‘set’ button and hold on until led displays figure ‘5’, press ‘...

  • Page 11

    11 setting processes ： 4.2 door travel limit setting 4.2.1 pull down the manual release lever, the door operator is under manual mode. 4.2.2 open the door by hand until the door touches the upper door stop. (see fig.7) close the door by hand until the door touches the ground . (see fig.8) 4.2.3 push...

  • Page 12: 4.3 Coding Transmitter

    12 4.2.5 press the red o/s/c button at the bottom of door operator or k button (fig.9), confirm the up limit and down limit are correct. If not, please re-set the travel limit according to above processes until the limits are correct. 4.3 coding transmitter 4.3.1 the operator should be under standby...

  • Page 13

    13 press ‘down’ button to decrease the force. The maximum force is 9, the minimum force is 1. The default is 3. 4.4.2 recommended force ： 5-15 kg resistance is recommended. Lightly lift the door while door closing, the door can be automatic reverse under approximate 5~15 kg resistance. 4.5 connectin...

  • Page 14: 4.6 Auto Close Setting:

    14 please confirm the photocells are well connection and programmed. Please check if the door will be automatically reversed when encountering an obstacle during door closing. 4.5.3 canceling the photocell function: press ‘down’ button and hold on until the led displays ‘h’ , press ‘down’ button the...

  • Page 15

    15 4.7 battery backup connection: it must use 24v dc 3.5ah sealed lead acid battery. Please open the light cover to connect the wires of battery with the battery backup terminal in the control board(fig.12). The ‘h’ of fig.11 is a hole for battery connection wires to through..

  • Page 16: 5. Common Trouble Shooting

    16 5. Common trouble shooting symptom possible reason solution the door does not move the door is locked or motor jammed main power not switch on switch on the main power the door is obstructed remove the barrier unlock the door check the motor is turning the door won’t reverse when obstructed the m...

  • Page 17

    17 the door can’t fully close the door is beyond the original up limit setting after power failure reset the limit position as per instruction a noise emits from the motor during the first manual travel limit setting the up/down limit position confirmation this is normal, no action required the door...

  • Page 18: 6. Packing List

    18 6. Packing list item quantity r3 roller door operator 1 remote 2 u-clamp and cast iron 1 extended fork 2 extended release arm 1 installation manual 1 weight bar (optional) 2 7. Technical data input voltage: 200 v ac ——240 v ac 50/60 hz controller voltage: 24 v dc max power: 235w lifting force: 40...

  • Page 19: 8. Final Notes

    19 8. Final notes this manual is only used by those who are qualified to carry out the installation. No given information in this manual can be considered of any interest to the end user. It is important for the installer to show their clients correct operation using of the opener including the usin...

  • Page 20

    20 distributed in new zealand by newfield group po box 11303, christchurch, new zealand www. Garageace .Co.Nz 0800 600 789.