Summary of S3
Page 1
Garage door opener owner’s manual s3.
Page 2
Features locking door after power failure: an advanced technology with patent. If power failure occurs while the door is opening, the door can be released by pulling the clutch down, moving the door to the closed position manually, the door can then be locked. By pressing the button on the remote wh...
Page 3
Resistance protection: the opener will check and set the force of the running resistant protection which ensures the opener has high sensitivity and adapts the running resistance fluctuation automatically even after the door is in service for a long time, manual adjustment is unnecessary. Photo cell...
Page 4
Contents 1. Required tool list 1 2. Important safety instructions 1 3. Opener installation 2 3.1 important installation instructions 2 3.2 installation sketch map 3 3.3 sectional rail assembling 3 3.4 opener installation 4 3.5 hoisting opener 4 3.6 installation of door opening limit 5 4. Adjustment ...
Page 5
1 1. Required tool list no. Name specification quantity 1 electric drill 1 2 ladder 1 3 mobile wrench or socket wrench 1 set 4 measuring tape 5m 1 5 screw driver - flat 2.5×100mm 1 6 screw driver - flat 6×200mm 1 7 screw driver - philips 6×200mm 2 8 pincer 2 9 allen key 10#、12# 1 2. Important safety...
Page 6
2 3. Opener installation 3.1. Important installation instructions in order to reduce the risk of serious injuries or death, please read and follow all instructions provided! 1) install only on a properly balanced door. An improperly balanced door has the potential to inflict severe injury. Have a qu...
Page 7
3 3.2. Installation sketch map as figure 1 shows the completed installation： 3.3. Sectional rail assembling 3.3.1. Rail connection take out the sectional rails (as shown in figure 2), put them in line on a clean and flat floor (as shown in figure 3). Connect the sectional rails (as shown in figure 4...
Page 8
4 3.4. Opener installation 3.4.1. Opener connection assemble opener as shown in figure 7, fasten four anti-loose screws(provided) m8 × 16. 3.4.2. C-type slide rail assembly and clutch cord fixing as shown in figure 8, fasten the clutch rod together with small head screws(provided) m6x20, ensure that...
Page 9
5 4 3 1 200-300 mm 2 1 2 5 6 3.5.2. Hoisting the opener as in fig12 showing, connect the rail to the front bracket on the wall, lift the motor side of the opener enough to make the rail level. Adjust the length of l1, and connect the perforated angle with bolts. The length of l2 can be cut according...
Page 10
6 4. Adjustment instructions open the cover as shown in fig16 showing before adjusting. 4.1. Ready status after switching on the power, the led lights will turn on for 2 seconds and off. Then the opener enters ready status, the led flashes slowly showing the door body’s position. As fig17 shows, fro...
Page 11
7 4.3.4. Open force setting press the “p” button until led shows as fig20. Pressing “+” and “-” will adjust the opening load force by adjusting the value from 0 to 9. After adjusting, press “p” to confirm. If you needn’t change the value, just press “p” and the system will automatically enter into n...
Page 12
8 4.4. Advanced setting in the ready status, press the “p” button until led shows the picture shows as fig25, then release the button. 4.4.1. Transmitter setting when the led turns on as fig 25. Press “+” or “-“ to set between 0 and 2. “0” stands for two button control; “1” stands for single button ...
Page 13
9 sw-wall photo al-in al-spk xt4 sw -w al l ph ot o al -i n al- sp k xt4 sw-wa ll photo al-in al- spk xt4 red black - battery + xt6 150m m 150m m 6. Accessory installation 6.1. Photo beam installation photo beam is an infrared protection system. If anything interrupts the infrared beam when the door...
Page 14
10 7. Maintenance and repair please inspect the automatic reversal and the door balance monthly, and adjust it if necessary. 8. Technical data a) max. Output power: 200 w b) max. Lifting force: 600 n c) opening and closing speed: 160 mm/s d) light: 12 v（high light led） e) motor: dc 24 v f) remote co...
Page 15
11 9. Trouble shooting the product appearance and functions will be changed by development without further notice. This manual is for reference only, the actual item is the standard. Trouble reason solution the motor doesn’t work and has no display on led ●opener is not powered on ●fuse on main cont...
Page 16
12 distributed in new zealand by newfield group po box 11303, christchurch, new zealand www. Garageace .Co.Nz 0800 600 789.