Garden Sun GS4400BK Owner's Manual - page 10

Page of 13

Download

Print this page

Bookmark us

Your heater was designed and approved for outdoor

use only. Do NOT use it inside a building, garage, or

any other enclosed area.

Make sure surrounding areas are free of combustible

materials, gasoline, and other flammable vapors or

liquids.

Ensure that there is no obstruction to air ventilation.

Be sure all gas connections are tight and there are no

leaks.

Be sure the cylinder cover is clear of debris.

Be sure any component removed during assembly or

servicing is replaced and fastened prior to starting.

Before Lighting:

Heater should be thoroughly inspected before each-

use, and by a qualified service person at least

annually.

If relighting a hot heater, always wait at least 5

minutes.

Inspect the hose assembly for evidence of excessive

abrasion, cuts, or wear. Suspected areas should be

leak tested. If the hose leaks, it must be replaced prior

operation.

Only

use

the

replacement

hose

assembly specified by manufacturer.

Lighting:

Note: This heater is equipped with a Pilot Light that allows

for safer startups and shutdowns. Pilot must be lit before

Main Burner can be started.

Push and release the Igniter button until pilot flame

is visible through Viewing Hole.

Release Control Knob after 30-60 seconds. Pilot

Light will remain lit. If not, return to step 1.

immediately. Flame is visible through Viewing Hole. If

Turn Control Knob to “PILOT”. Main Burner will light

not, return to step 1.

If for some reason your igniter fails to deliver a spark,

your heater can be started by inserting a lit match

through the pilot view hole while pushing the control

knob in while in the PILOT position.

Turn Cylinder Valve ON.

Open Viewing Hole by sliding cover to either side.

Push Control Knob IN and rotate to Pilot position.

Note: For initial start or after any cylinder change, hold

Control Knob IN for 2 minutes to purge air from gas lines

before proceeding.

Note: If pilot fails to remain lighted, all valves should be closed

and waiiting period of at least 5 minutes should pass before

attempting to light.

« ‹ Prev 7 8 9 10 11 12 13 Next › »

Summary of GS4400BK

Page 1
Owner’s manual csa international requirement no.5.90.Us (5th edition) important read this manual carefully before assembling, using or servcing this heater keep this manual for future reference. Patio heater r r gs4400ss gs4400gn gs4400bk gs4400cp gs4400gd gs4400wh.
Page 2
1 contents general safety information....................................... 1 s n o i t c u r t s n i y l b m e s s a components & hardware........................................ 3 additional requirements ........................................ 3 s s e c o r p n o i t a ll a t s n i step1 - attac...
Page 3
2 danger • explosion - fire hazard • keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • provide adequate clearances around air openings into the combustion chamber. • never use the heater in spaces which...
Page 4
3 warning • this product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone. • propane gas i...
Page 5
4 picture qty description used in step(s) 6 large bolt 4 5 medium bolt 1 & 3 4 small bolt 4 large screw 2 9 small screw 8 9 large flat washer 6 & 9 9 small flat washer 8 2 large flange nut 1 6 small flange nut 4 4 large nut 2 9 cap nut 8 3 wing nut 9 3 reflector stud 6 1 wrench 1 / 3 / 4 / 7 / 8 add...
Page 6
5 . Lay bucket inside of base and screw on large nut. Tighten with philips screwdriver. . For improve the stability , please fill the bucket with sand. Step 3 – attach support brackets to base . Attach three support brackets loosely to base with three medium bolts downward through support brackets i...
Page 7
6 . Load head assembly by inserting hose into post. . Insert head assembly into post. . Control knob should be above decal on post. . Attach head assembly to post, and loosely install four small bolts. . Tighten bolts securely. (for models with entire reflector , skip to step 9) step 8 – install ref...
Page 8
7 step 9 – attach reflector assembly to studs . Support heater. . Slide 3 large flat washers over threaded end of studs. . Locate reflector assembly on 3 studs. . Install large flat washers on studs & securely tighten wing nuts but do not over-tighten! Step 10 – connect hose & regulator to cylinder ...
Page 9
8 leak check warning • perform all leak tests outdoors. • extinguish all open flames. • never leak test when smoking. • do not use the heater until all connections have been leak tested and do not leak. Hose / regulator connection regulator / cylinder connection . Make 2-3 oz. Of leak check solution...
Page 10
9 . Your heater was designed and approved for outdoor use only. Do not use it inside a building, garage, or any other enclosed area. . Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids. . Ensure that there is no obstruction to air ventilat...
Page 11
10 if you experience any ignition problem please consult “troubleshooting” on page 11. Caution: avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The ...
Page 12
11 troubleshooting if the problem is: and this condition exists: then do this pilot won’t light cylinder valve is closed open valve blockage in orifice or pilot tube clean or replace orifice or pilot tube air in gas line open gas line and bleed it (pressing control knob in) for not more than 1 - 2 m...
Page 13
12 . Gas odor with extreme yellow tipping of flame. . Heater does not reach the desired temperature. . Heater glow is excessively uneven. . Heater makes popping noises. Ґ . Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Cl...