Summary of HSS-RS-GH
Page 1
Model #hss-rs-gh outdoor patio heater 1.
Page 2
Package contents 2 n o i t p i r c s e d t r a p quantity a reflector panel 3 b reflector plate 1 ff reflector stud 3 c head assembly 1 d cylinder housing e post f gas hose h base g support bracket i wheel kit j regulator 1 1 1 3 1 1 1 a b ff c e h f j d g i.
Page 3
Hardware contents (shown actual size) 3 aa ii dd ee hh cc ff bb gg reflector spacer qty. 3 washer Φ8 qty. 9 washer Φ6 qty. 9 screw m6 x 10 qty. 9 cap nut qty. 9 wrench qty. 1 (not actual size) jj kk wing nut qty. 3 ll stainless steel bolt qty. 4 bolt m8 x 16 qty. 5 bolt m6 x 30 qty. 5 m8 flange nut ...
Page 4
4 safety information danger • carbon monoxide hazard • this heater is a combustion appliance. All combustion appliances produce carbon monoxide (co) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of co if used and maintained in accordance w...
Page 5
5 preparation before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. Estimated assembly tim...
Page 6
6 assembly instructions hardware used aa bb hardware used 1 2 3 1. Attach wheel assembly (i) to base (h). Line up holes in wheel bracket with corresponding holes in base, insert two bolts m8 x 16 (bb) through holes, and finger tighten two m8 flange nuts (aa) . Be sure that the wheel assembly is para...
Page 7
7 assembly instructions 4 5 4. Load cylinder housing onto post. Slide cylinder housing down. 5.Attach reflector spacers (ff) and three washers Ø8 (gg) to screen cover. Tighten the reflector spacers. Unscrew four stainless steel bolts (dd). 6. Load head assembly by inserting hose into post. Insert he...
Page 8
8 assembly instructions hardware used hh ii jj 7 tt 7 . Warning:remove protective cover before assembling. Note: if necessary for proper alignment of reflector sections, loosen each bolt prior to further assembly and retighten after sections are aligned. 8. Slide two reflector panels together. Inser...
Page 9
9 assembly instructions hardware used gg kk 10 11 10. Support heater. Slide three washers washer Φ8 (gg) over threaded end of spacer. Locate reflector assembly on 3 spacers. Install three washers Φ8 on spacers and securely tighten wing nuts (kk) but do not overtighten. 11. Connect hose and regulator...
Page 10
10 assembly instructions a dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for lp gas c...
Page 11
11 operation instructions leak check 1. Make 2-3 oz. Of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3. Apply several drops of solution where regulator connects to cylinder. 4. Make sure all pa...
Page 12
12 operation instructions danger • carbon monoxide hazard • for outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Before turning gas supply on: 1. Your hea...
Page 13
13 operation instructions 5. Push and release the igniter button until pilot flame is visible through viewing hole. 6. Once the pilot is lit, continue to depress the control knob for 30 seconds. 7. If the pilot does not stay lit, repeat steps 4 to 6. 8. If after repeating steps 4 to 6 unit does not ...
Page 14
14 operation instructions shut down: 1. Turn control knob clockwise to pilot. (normally, burner will make a slight popping sound when extinguished.) burner will extinguish but pilot will remain on. 2. To extinguish pilot depress control knob and continue to turn it clockwise to off. 3. Turn cylinder...
Page 15
15 operation instructions care and maintenance 9. Heater is away from gasoline or other flammable liquids or vapors. 10. Heater is away from windows, air intake openings, sprinklers and other water sources. 11. Heater is at least 24 in. On top and at least 36 in. On sides from combustible materials....
Page 16
16 care and maintenance gas odor with extreme yellow tipping of flame. Heater does not reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe fo...
Page 17
17 troubleshooting problem possible cause corrective action pilot won’t light pilot won’t stay lit burner won’t light burner flame is low carbon build-up thick black smoke cylinder valve is closed open valve blockage in orifice or pilot tube air in gas line low gas pressure with cylinder valve fully...
Page 18
18 one-year limited warranty this product is inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part (excluding light bulbs and fuses*) within one year from the date of purchase proves to be defective in material or fabrication under normal use, the part ...
Page 19
Replacement parts list 19 printed in china n o i t p i r c s e d t r a p quantity a reflector panel 3 b reflector plate 1 ff reflector stud 3 c head assembly 1 d cylinder housing e post f gas hose h base g support bracket i wheel kit j regulator 1 1 1 3 1 1 1 a b ff c e h f j d g i.