1 garden treasures® is a registered trademark of lf, llc. All rights reserved. Attach your receipt here serial number purchase date questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.M. - 8 p.M., est, monday - friday. It...
2 table of contents for your safety if you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. Do not store or use gasoline or other flammable vapors and liquids in th...
3 product specifications certification csa height overall 86.6 inches reflector diameter 31.5 inches rated heat input 45,000 btu/hr fuel propane-lp gas supply 20-lb lp-gas cylinder manifold pressure 11 inches w.C. Injector size (diameter) 2.07 mm safety features thermocouple & tilt switch gas supply...
4 package contents part description quantity part description quantity a top dome 1 g deck ring 1 b kd dome 4 h cylinder assembly 1 c burner assembly 1 i base 1 d pole assembly 1 j wheel assembly 1 e table 1 k cover 1 f table support assembly 1.
5 hardware contents preparation before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated assembly time: 30 minutes. Tools required f...
6 safety information please read and understand this entire manual before attempting to assemble, operate or install the product. Z california proposition 65 warning: chemicals known to the state of california to cause cancer, birth defects or other reproductive harm are created by combustion of pro...
7 safety information z installation and repair should be done by qualified service person; the heater should be inspected before use and at least annually by a qualified service person. Z do not obstruct the flow of combustion and ventilation air. Z the lp-gas supply cylinder to be used must be: (a)...
8 assembly instructions hardware used hardware used hardware used 2 i bb 1. With the base (i) upside down, attach wheel assembly (j) using m8 x 15 mm bolts (aa) and m8 nuts (cc). 2. Turn the base (i) right-side up, then attach cylinder assembly (h) using m5 x 8 mm black bolts (bb) though preassemble...
9 assembly instructions hardware used 4. Attach table support assembly (f) to the bottom of table (e) with st4.2 x 8 mm screws (ee). 5. Unlock the handle on the table support assembly (f), then insert the table (e) onto the pole assembly (d). Once the desired height is achieved, re-lock handle on th...
10 assembly instructions hardware used hardware used 7 7. Thread the regulator assembly preassembled to burner assembly (c) through the pole assembly (d). Once the burner assembly (c) rests on pole assembly (d), secure with m5 x 8 mm silver bolts (gg). X 3 m5 x 10 mm bolt gg 6. Insert reflector spac...
11 assembly instructions hardware used hardware used 8. Attach kd domes (b) using m5 nuts (hh), m5 washers (ii) and m5 x 8 mm silver bolts (gg). Then, complete dome assembly by attaching top dome (a) to kd domes (b) using m5 nuts (hh), m5 washers (ii) and m5 x 8 mm bolts (gg). 9. Attach dome assembl...
12 assembly instructions 11 10 11. Attach strap inside of cylinder assembly (h) to secure cylinder. Then, close door on cylinder assembly (h) to complete installation. 10. Connect the preassembled regulator assembly from burner assembly (c) to a 20-lb. Lp-gas cylinder (sold separately). Line up thre...
13 assembly instructions operating instructions igniter igniter c ll 12. To install the battery (dd), unscrew the igniter cap preassembled to burner assembly (c). Insert battery (dd) into the igniter, ensuring the positive "+" end faces outward. Then replace the igniter cap. 12 checking for leaks a....
14 operationg instructions lighting instructions 1 1. Turn the lp gas cylinder valve off. Push the control knob on the pole in, turn off, and wait 5 minutes for any gas to clear. 2. Turn the tank valve on. Push control knob in and rotate to push. Then push the igniter button and control knob until t...
15 operationg instructions 0 care and maintenance z abrasive cleaners will damage this product. Z never use oven cleaner to clean any part of heater z do not clean any heater part in a self-cleaning oven. The extreme heat will damage the finish. Z more frequent cleaning may be required as necessary....
16 care and maintenance cleaning z wipe surfaces clean with mild dish detergent or baking soda. Z for stubborn surfaces use a citrus-based degreaser and a nylon scrubbing brush. Z rinse clean with water. Note: while cleaning the unit, be sure to keep the area around the burner and pilot assembly dry...
17 troubleshooting problem possible cause corrective action burner doesn’t light 1. Gas pressure is low. 2. The orifice is blocked. 3. Control knob is not in “on” position. 1. Turn the gas cylinder valve “off” and replace the cylinder. 2. Clear blockage. 3. Turn control knob to “on” burner flame is ...
18 replacement parts list for replacement parts, call our customer service department at 1-800-643-0067, 8 a.M. - 8 p.M., est, monday – friday. Part description part # 1 top dome 5007755 2 kd dome 5007756 3 burner chamber assembly 5203139 4 burner assembly 0574423-4 5 knob 2100462 6 valve shroud cov...
