- DL manuals
- Gardena
- Lawn and Garden Equipment
- 1242
- Operating Instructions Manual
Gardena 1242 Operating Instructions Manual
Summary of 1242
Page 1
D gb e s dk gardena ® d betriebsanleitung programmiereinheit gb operating instructions programming unit e manual de instrucciones unidad de programación s bruksanvisning programmeringsenhet dk brugsanvisning programmeringsenhed art. 1242.
Page 2: Gardena Programming Unit
Intended use please note 13 gb contents gardena programming unit welcome to the garden of gardena... Translation of the original instructions from german. Please read these operating instructions carefully and observe the notes given. Use these instructions to familiarise yourself with the programmi...
Page 3: 2. For Your Safety
14 gb 2. For your safety only alkaline batteries of the type 9 v iec 6lr61 should be used to attain the maximum running time of 1 year. We recommend e.G. The manufacturers varta and energizer. V to prevent data transfer errors, the battery must be replaced in good time. It can occur that the lcd dis...
Page 4: 4. Putting Into Operation
Insert the battery in the programming unit : insert the battery in the control unit : b c d e a 0 7 9 8 6 15 gb battery condition in the control unit : if the battery capacity is exhausted while the control unit is con- nected, then the symbol batt. Ext. Will start to blink as soon as data has been ...
Page 5
Setting the time and day : 1. 2. 3. 4. 16 gb 5. Operating your programming unit structure of the 3 programme levels there are three programme levels: main level : • after all programming has been completed: – the current time and current day are displayed – the watering programmes with entries are d...
Page 6
4. 5. 6. 17 gb watering programmes ( level 2) prerequisite : you must have entered the current time and current day. For reasons of clarity, we recommend that you record the data for your irrigation valves in the watering plan in the appendix of the operating instructions before you begin entering w...
Page 7
Changing an existing watering programme : ending the programming mode early : reset : 18 gb 7. (a) watering cycle every 2nd or 3rd day : set the arrow ê to 2nd or 3rd using the ▲ - ▼ keys (for example 3rd = every 3rd day) and confirm by pressing the ok key. The watering programme is saved. The water...
Page 8
Receiving watering programmes (transferring to the programming unit) : 19 gb transferring watering programmes data can only be transferred if both the programming unit and the control unit are properly equipped with a 9 v battery. The programming unit must also be set to the main level. The control ...
Page 9: 6. Trouble-Shooting
20 gb manual watering prerequisite : the lever of the irrigation valve must be set to the “auto” position. 1. Press the on / off key on the control unit. Manual watering starts. 2. Press the on / off key on the control unit during manual watering. Manual watering is ended prematurely. After putting ...
Page 10: 7. Putting Out of Operation
21 gb fault possible cause remedy error 2 poor contact at the plug con- v check contact at the plug flashes on the display nection. Connection. (data transfer error) battery in the control unit v replace battery in control is low. Unit. Error 3 after a longer period of storage 1. Replace battery. Fl...
Page 11: 9. Service / Warranty
22 gb 9. Service / warranty gardena guarantees this product for 2 years ( from date of purchase). This guarantee covers all serious defects of the unit that can be proved to be material or manufacturing faults. Under warranty we will either replace the unit or repair it free of charge if the followi...
Page 12
D produkthaftung wir weisen ausdrücklich darauf hin, dass wir nach dem produkthaftungsgesetz nicht für durch unsere geräte hervorgerufene schäden einzustehen haben, sofern diese durch unsachgemäße reparatur verursacht oder bei einem teileaustausch nicht unsere original gardena teile oder von uns fre...
Page 13
54 bezeichnung des gerätes : programmiereinheit description of the unit: programming unit descripción de la mercancía : unidad de programación produktbeskrivning : programmeringsenhet beskrivelse af enhederne : programmeringsenhed art.-nr.: art. No.: art. Nº: 1242 art.Nr. : varenr. : eu-richtlinien ...
Page 14
55 prog. Start time run time 3rd 2nd mo tu we th fr sa su 1 7: 30 0: 30 x x x 2 17: 30 0: 20 x x 3 22: 30 1: 10 x x 4 4: 00 0: 15 x 5 –:– –:– 6 –:– –:– prog. Start time run time 3rd 2nd mo tu we th fr sa su 1 7: 30 0: 30 x x x 2 17: 30 0: 20 x x 3 22: 30 1: 10 x x 4 4: 00 0: 15 x 5 –:– –:– 6 –:– –:–...
Page 15
56 deutschland / germany gardena gmbh central service hans-lorenser-straße 40 d-89079 ulm produktfragen: (+ 49) 731 490 - 123 reparaturen: (+ 49) 731 490 - 290 service @ gardena.Com albania cobalt sh.P.K. Rr. Siri kodra 4000 tirana argentina husqvarna argentina s.A. Vera 745 (c1414aoo) buenos aires ...