1. DL manuals
  2. Gardif
  3. Lawn Mower
  4. M3E1032G
  5. Instruction Manual

Gardif M3E1032G Instruction Manual

Manual is about: ELECTRIC ROTARY MOWER 1000 WATT

Summary of M3E1032G

  • Page 1

    Instruction manual translated from original manual electric rotary mower 1000 watt model me1032g-ge instruction manual (factory model m3e1032g) important — please read these instructions fully before starting assembly and operating the mower these instructions contain important information that will...

  • Page 2: Safety Information

    Safety information important! - please read these instructions fully and comply with them, before starting assembly and operating the mower. It is important to consult these instructions in order to acquaint yourself with the unit, its proper use and safety regulations. Keep this manual in a safe pl...

  • Page 3

    Sharp blade. Beware of injury to toes and fingers. Disconnect from the mains supply before any maintenance work. Warning. Beware of electric shocks. Keep the mains supply cord away from the cutting blade. Wait until all moving parts have stopped completely before touching them. The blade may continu...

  • Page 4: General Safety

    Important! When using this equipment, the following safety precautions must be followed to avoid injuries and damage. - read all operating instructions carefully and comply with them. It is important to understand these instructions and to acquaint yourself with the machine, its correct usage and al...

  • Page 5: Safety Information

    Safety information important - please read these instructions fully before starting assembly personal safety note! Only supply power to the equipment through circuit protected by an rcd with a maximum trip current of 30 ma. Use only plugs or connectors approved for outdoor usage. Extension cables mu...

  • Page 6

    Always check the mower for signs of damage before each usage. Always disconnect the mains lead from the electrical supply before carrying out any inspection, servicing or maintenance work. Ensure that all the guards are securely fitted and in good working order. Check the grass collector at regular i...

  • Page 7

    Never run the mower in enclosed or poorly ventilated rooms or if there are inflammable or explosive fluids. Vapors or gases nearby. Switch off the motor and disconnect the mains lead before clearing blockages in the grass ejection area and before you inspect it if the mower has struck a foreign body. ...

  • Page 8

    Make sure you keep your feet at a safe distance from the mower blade at all times! Do not stand near the grass ejection chute if the grass collector is not fitted. The safety distance from the moving blade produced by the push handle must be maintained at all times. If you use the mower on a small in...

  • Page 9

    Do not leave the mower out in the rain. The lawn must not be wet or very damp. Only push the mower at a normal walking pace. Be particularly careful when you change the direction of the mower or pull it towards you. Do not pulling it towards you while the blade is moving. Switch off the mower if it ...

  • Page 10

    Operating and maintenance safety caution! Read all safety requirements and instructions. Any errors made in following the safety requirements and instruction may result in an electric shock. fire and serious injury. Keep all safety regulations and instructions in a safe place for future use. Do not u...

  • Page 11: In The Box

    In the box parts 1 - on/off switch double lever 2 - cable strain-relief clamp 3 - switch box 4 - top push handle 5 - bottom handle support 6 - grass deflector 7 - grass box 7a - grass box housing halves 8 - motor housing 9 - cable clips 10 - fastening screws for bottom handle support (x2) 11 - faste...

  • Page 12: Assembly

    Assembly step 1 - handle assembling 2a- 2b. Fit a bottom handle support 5 into the opening provided for it and secure it as shown in fig. 2b with a screw 10. Proceed in the same way on the other side. 2c. When you fit the top push handle you can decide the height of the push handle by selecting the a...

  • Page 13

    Step 2 - grass collector assembly 3a. Align the fronts end of the top half and the bottom half of the grass box. Clip the two halves together starting at the front..

  • Page 14

    3b. Once the front clips on either side are secure, work back on either side to secure each clip. This method will help to keep the two halves of the box aligned. 3c. Fit the handle 12 into the top half of the grass box 7a. 3d. Before you fit the grass box onto the mower you must ensure that the moto...

  • Page 15

    Operating instructions and tips setting the cutting heights important! Set the cutting height only when the motor is switched off and the power cable has been disconnected. The cutting height is adjusted as shown in figs. 4a and 4b.To do this, turn the hub cap clockwise to release the bolt (fig. 4a)...

  • Page 16

    Operating instructions and tips operation before you connect the mower to the mains supply make sure that the data on the rating plate is identical to the mains data. Connect the plug to an extension cable if necessary. It is imperative to secure the extension cable to the handle with the cable grip...

  • Page 17

    Mowing advice we recommend that you mow in overlapping lines. Only mow with a sharp blade so that the blades of grass do not fray. Frayed grass blades may turn yellow. To achieve a good cut, guide the lawn mower in lines that are as straight as possible. These lines should always overlap by a few ce...

  • Page 18: Maintenance

    Maintenance cleaning & maintenance always disconnect the mains power plug engaging in any cleaning work. Cleaning: keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a soft brush or blow it with compressed air at low pressure af...

  • Page 19

    When fitting the blade, making sure it is installed in the right direction. The wings on the blade must be on the top (nearest to the deck). Then retighten the fastening bolt. The tightening torque should be approx 25 nm. Important! Always wear work gloves when engaging in any maintenance work. Only...

  • Page 20: Troubleshooting

    Troubleshooting general troubleshooting.

  • Page 21: Technical Data

    Technical data technical data table m3e1032g specification value voltage 220-240v~ 50hz power input 1000w motor speed n 0 3500min -1 cutting width 320 mm volume of grass collector 27 lt. Cutting height adjustment 20/40/60 mm weight 9,35 kg. Protection class ii – ip24 lpa sound pressure level l pa =8...

  • Page 22

    Ec declaration of conformity serial number : see front page we, company, gardif sas za de l’europe 60, avenue de bruxelles 77310 st fargeau ponthierry france the undersigned, bruno van elslande, managing director the person authorised to compile the technical file : yuxi wang, quality engineer decla...