Summary of 605
Page 1
Edge ® 605/705 mb gps-enabled bike computer quick reference guide.
Page 2: Warning
Warning : this product contains a lithium-ion battery. See the important safety and product information guide in the product box for important battery safety information. Buttons ➊ ➋ ➏ ➎ ➌ ➍ ➐ ➊ power press and hold to turn the edge on/off. Press to turn the backlight on/off. ➋ mode press to return ...
Page 3: Thumb Stick/enter
➍ thumb stick/enter move the thumb stick to scroll through menus, options, and data fields. Press in the thumb stick to select options and to acknowledge messages. ➎ start/stop press to start/stop the timer. ➏ menu press to open the menu page. Press and hold to lock/unlock the edge buttons. ➐ in/out...
Page 4: Step 1: Charge The
Step 1: charge the battery you can charge the edge using the ac charger or the usb cable and your computer. Note: to prevent corrosion, thoroughly dry the mini-usb port, weather cap, and surrounding area before charging or connecting to a personal computer. To charge the edge: 1. On the back of the ...
Page 5: To Install The Edge On Your
Be used under the mount for a better viewing angle. To install the edge on your bike stem: 1. Place the wedge on the bike stem, and then place the bike mount on the wedge. Make sure the release lever is on the left. Wedge bike mount release lever for horizontal bars: separate and remove the top part...
Page 6: To Release The Edge:
4. Slide the edge to the left until it snaps into place. To release the edge: press down on the release lever, and slide the edge to the right. Step 3: turn on your edge press and hold to turn on your edge. Follow the on-screen configuration instructions. Step 4: acquire satellite signals it may tak...
Page 7: Heart Rate Monitor
Heart rate monitor wear the heart rate monitor directly on your skin, just below your breastplate. It should be snug enough to stay in place during your run. 1. Push one tab on the strap through the slot in the heart rate monitor. Press the tab down. 2. Wet both sensors on the back of the heart rate...
Page 8: Gsc 10
Gsc 10 both magnets must be aligned with their respective indication lines for the edge to receive data. To install the gsc 10: 1. Place the gsc 10 on the rear chain stay (on the side opposite the drive train). Loosely attach the gsc 10 using two cable ties. 2. Attach the pedal magnet to the crank a...
Page 9: Reset
Not enough room between the sensor arm and the spoke. The magnet must be aligned with the sensor arm indication line. 4. Loosen the screw on the sensor arm and move it to within 5 mm of the spoke magnet. You can also tilt the gsc 10 closer to either magnet for improved alignment. 5. Press the reset ...
Page 10: Step 7: Set Your
6. When everything is aligned and working correctly, tighten the cable ties, sensor arm, and spoke magnet. Step 7: set your set your profiles the edge uses information that you enter about yourself and your bike to calculate accurate ride data. To set your user profile: press menu > select settings ...
Page 11: Step 9: Download Free
Step 9: download free software 1. Go to www.Garmin.Com/edge . 2. Follow the on-screen instructions to download garmin training center ® or garmin connect ™ . Step 10: transfer history to your computer 1. Plug the small end of the usb cable into the mini-usb port on the back of the edge (under the we...
Page 12
© 2007 garmin ltd. Or its subsidiaries garmin ® is a trademark of garmin ltd. Or its subsidiaries, registered in the usa and other countries. Garmin training center ® , edge ® , garmin connect ™ , gsc ™ 10, dynastream ™ , ant ™ , and ant+sport ™ are trademarks of garmin ltd. Or its subsidiaries. The...