1. DL manuals
  2. Garmin
  3. Toy
  4. G1000H
  5. Pilot's Manual

Garmin G1000H Pilot's Manual

Manual is about: Integrated Flight Deck Pilot’s Guide for the Bell 407GX

Summary of G1000H

  • Page 1

    G1000h ™ integrated flight deck pilot’s guide bell 407gx.

  • Page 3

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx copyright © 2011 garmin ltd. Or its subsidiaries. All rights reserved. This manual reflects the operation of system software version 1237.00 or later for the bell 407gx helicopter. Some differences in operation may be observed when...

  • Page 4

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A ii limited warranty limited warranty within the warranty period, garmin will, at its sole discretion, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer f...

  • Page 5

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx iii warnings, cautions, and notes warning: navigation and terrain separation must not be predicated upon the use of the terrain avoidance feature. The terrain avoidance feature is not intended to be used as a primary reference for ...

  • Page 6

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A iv warnings, cautions, and notes warning: the united states government operates the global positioning system and is solely responsible for its accuracy and maintenance. The gps system is subject to changes which could affect the a...

  • Page 7

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx v warnings, cautions, and notes note: all visual depictions contained within this document, including screen images of the panel and displays, are subject to change and may not reflect the most current system and databases. Depicti...

  • Page 8

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A vi revision information record of revisions part number revision date page range description 190-01255-00 a february, 2011 all initial release.

  • Page 9

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx vii table of contents section 1 system overview 1.1 system description ................................................. 1 1.2 line replaceable units (lru) ................................. 2 1.3 g1000h controls ......................

  • Page 10

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A viii table of contents intercom .................................................................. 123 clearance recorder and player (optional) ................... 129 split com ........................................................

  • Page 11

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx ix table of contents section 8 additional features 8.1 synthetic vision system (svs) ........................... 372 svs operation .......................................................... 373 svs features ...........................

  • Page 12

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A x table of contents b lank p age.

  • Page 13: Section 1  System Overview

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 1 system overview section 1 system overview 1.1 system description this section provides an overview of the g1000h integrated flight deck as installed in the bell 407gx. The g1000h system is an integrated flight control system that...

  • Page 14

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 2 system overview 1.2 line replaceable units (lru) •gdu 1040h (2) – one unit is configured as a pfd, the other as an mfd, each featuring a 10.4-inch lcd with 1024 x 768 resolution. The unit installed on the right/pilot side is desi...

  • Page 15

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 3 system overview •gsc 46 (1) – the gsc 46 is a signal conditioner which converts tachometer and engine torque information to a digital format for use by the gea 71h. •grs 77h (1) – provides aircraft attitude and heading informatio...

  • Page 16

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 4 system overview •gdl 69ah (1) – a satellite radio receiver that provides real-time weather information to the g1000h mfd (and, indirectly, to the inset map of the pfd) as well as digital audio entertainment. The gdl 69ah communic...

  • Page 17

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 5 system overview •ga 58 (2) – the ga 58 are directional antennas for the traffic avoidance system. One top-mounted directional antenna is required. Optional bottom mounted antenna offers better threat visibility. •ga 36 (1) and ga...

  • Page 18: 1.3  G1000H Controls

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 6 system overview 1.3 g1000h controls note: the audio panel (gma 350) are described in the cns & audio panel. The g1000h system controls are located on the pfd and mfd bezels and audio panel. The controls for the pfd and mfd are di...

  • Page 19

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 7 system overview 5 joystick turn to change map range press to activate map pointer for map panning 6 crs/baro knob turn large knob for altimeter barometric pressure setting turn small knob to adjust course (only when hsi is in vor...

  • Page 20: Audio Panel Controls

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 8 system overview the nav, crs/baro, com, fms, and alt knobs are concentric dual knobs, each having small (inner) and large (outer) control portion. When a portion of the knob is not specified in the text, either may be used. Large...

  • Page 21

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 9 system overview 8 music key selects and deselects music audio. 9 man sq key manual squelch annunciator. When lit, squelch is controlled manually. 10 volume indicator indicates volume/squelch setting relative to full scale. 11 fro...

  • Page 22: 1.4  Secure Digital Cards

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 10 system overview 1.4 secure digital cards note: refer to the appendices for instructions on updating the aviation database. Note: ensure that the g1000h system is powered off before inserting the sd card. The pfd and mfd data car...

  • Page 23: 1.5  System Power-Up

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 11 system overview 1.5 system power-up note: refer to the appendices for ahrs initialization bank angle limitations. Note: see the appendices for additional information regarding system-specific annunciations and alerts. Note: see ...

  • Page 24: 1.6  System Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 12 system overview 1.6 system operation note: in normal operating mode, backlighting can only be adjusted from the pfd. In reversionary mode, it can be adjusted from the remaining display. The displays are connected together via a ...

  • Page 25

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 13 system overview reversionary display operation note: the g1000h system alerts the pilot when backup paths are utilized by the lrus. Refer to appendix a for further information regarding system-specific alerts. In the event of a ...

  • Page 26: Ahrs Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 14 system overview ahrs operation note: refer to the appendices for specific ahrs alert information. Note: aggressive maneuvering while the ahrs is not operating normally can degrade ahrs accuracy. In addition to using internal sen...

  • Page 27

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 15 system overview air data input failure a failure of the air data input has no effect on ahrs output while ahrs is operating in normal mode. A failure of the air data input while the ahrs is operating in reversionary no-gps mode ...

  • Page 28: Softkey Function

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 16 system overview softkey function the softkeys are located along the bottoms of the displays. The softkeys shown depend on the softkey level or page being displayed. The bezel keys below the softkeys can be used to select the app...

  • Page 29

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 17 system overview pathway displays rectangular boxes representing the horizontal and vertical flight path of the active flight plan syn terr enables synthetic terrain depiction hrzn hdg displays compass heading along the zero-pitc...

  • Page 30

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 18 system overview stby selects standby mode (transponder does not reply to any interrogations) on selects mode a (transponder replies to interrogations) alt selects mode c – altitude reporting mode (transponder replies to identifi...

  • Page 31

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 19 system overview figure 1-15 pfd configuration softkeys press the back softkey to return to the top-level softkeys alt unit meters in hpa hsi frmt 360 hsi arc hsi (optional) syn vis syn terr hrzn hdg pathway aptsigns msg msg msg ...

  • Page 32

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 20 system overview mfd softkeys engine displays the eis-engine page cas ↑ scroll up (displayed only when a sufficient number of items are displayed in the crew alerting system display to warrant scrolling) cas ↓ scroll down (displa...

  • Page 33: Gps Receiver Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 21 system overview dcltr selects desired amount of map detail; cycles through declutter levels: dcltr (no declutter): all map features visible dcltr-1: declutters land data dcltr-2: declutters land and sua data dcltr-3: removes eve...

  • Page 34

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 22 system overview viewing gps receiver status information 1) use the large fms knob on the mfd to select the auxiliary page group (see section 1.7 for information on navigating mfd page groups). 2) use the small fms knob to select...

  • Page 35

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 23 system overview the gps status page provides the following information: •satelliteconstellationdiagram satellites currently in view are shown at their respective positions on a sky view diagram. The sky view is always in a north...

  • Page 36

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 24 system overview because of the tighter protection limit on approaches, there may be times when raim is not available. The g1000h automatically monitors raim and warns with an alert message when it is not available. If raim is no...

  • Page 37

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 25 system overview disabling waas, egnos or msas 1) select the gps status page. 2) if necessary, select the sbas softkey. 3) press the fms knob, and turn the large fms knob to hightlight the desired sbas system. 4) press the ent ke...

  • Page 38: Menus

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 26 system overview 1.7 accessing g1000h functionality menus the g1000h has a menu key that, when pressed, displays a context-sensitive list of options. This options list allows the user to access additional features or make setting...

  • Page 39: Mfd Page Groups

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 27 system overview mfd page groups note: refer to the flight management, hazard avoidance, and additional features sections for details on specific pages. Information on the mfd is presented on pages which are grouped according to ...

  • Page 40

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 28 system overview figure 1-21 map pages map pages (map) navigation map traffic map weather data link (service optional) htaws figure 1-22 waypoint pages airport information pages waypoint pages (wpt) airport information pages - ai...

  • Page 41

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 29 system overview auxiliary pages (aux) weights, fuel, exceedances trip planning utility gps status system setup - system setup 1 (setup 1 softkey) - system setup 2 (setup 2 softkey) xm radio - xm information (info softkey) - xm r...

  • Page 42

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 30 system overview the flight plan pages may also be accessed using the fpl key. Main pages within this group are selected by turning the small fms knob. The checklist page may be accessed from the page group tab or the chklist sof...

  • Page 43: Mfd System Pages

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 31 system overview mfd system pages in the auxiliary (aux) page group, there are two system pages: system setup and system status. The system setup page allows management of various system parameters, while the system status page d...

  • Page 44

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 32 system overview figure 1-28 system setup 2 page d ate /t ime the date/time box on the system setup 1 page displays the current date and time and allows the pilot to set the time format (local 12-hr, local 24-hr, or utc) and offs...

  • Page 45

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 33 system overview d isplay u nits units in which various quantities are displayed on the g1000h screens are listed on the system setup 1 page. The navigation angle reference and the position units are pilot selectable. Category se...

  • Page 46

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 34 system overview baro t ransition a lert see the flight instruments section for a discussion on setting the baro transition alert. A irspace a lerts the airspace alerts box allows the pilot to turn the controlled/special-use airs...

  • Page 47

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 35 system overview 5) turn the large fms knob to select the on/off field in the arrival alert box. 6) turn the small fms knob clockwise to turn the airspace alert on or counterclockwise to turn the alert off. 7) press the fms knob ...

  • Page 48

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 36 system overview the following data may be selected for display in each of the four fields of the navigation status box. •bearing(brg) •distance(dis) •desiredtrack(dtk) •enroutesafealtitude(esa) •estimatedtimeofarrival(eta) •esti...

  • Page 49

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 37 system overview to change com channel spacing: 1) while on the system setup 1 page, press the fms knob momentarily to activate the flashing cursor. 2) turn the large fms knob to highlight the channel spacing field in the com con...

  • Page 50

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 38 system overview figure 1-29 pilot profiles (system setup page) creating a profile: 1) turn the large fms knob to select the aux page group. 2) turn the small fms knob to select system setup. 3) press the fms knob momentarily to ...

  • Page 51

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 39 system overview renaming a profile: 1) while on the system setup 1 or setup 2 page, press the fms knob momentarily to activate the flashing cursor. 2) turn the large fms knob to highlight ‘rename’ in the pilot profile box. 3) pr...

  • Page 52

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 40 system overview enabling htaws voice callouts: 1) turn the large fms knob to select the aux page group. 2) turn the small fms knob to select system setup. 3) if necessary, press the setup 2 softkey to select the system setup 2 p...

  • Page 53

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 41 system overview utility page for flight planning purposes, timers, trip statistics, and a scheduler feature are provided on the aux - utility page. The timers available include a stopwatch-like generic timer, a total time in fli...

  • Page 54

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 42 system overview 6) to stop the timer, press the ent key with ‘stop?’ highlighted. The field changes to ‘reset?’. 7) to reset the timer, press the ent key with ‘reset?’ highlighted. The field changes back to ‘start?’ and the digi...

  • Page 55

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 43 system overview t rip s tatistics the odometer and trip odometer record the total mileage traveled from the last reset; these odometers can be reset independently. Resetting the trip odometer also resets the average trip grounds...

  • Page 56: 1.8  Display Backlighting

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 44 system overview 1.8 display backlighting the g1000h display and control backlighting can be adjusted either automatically or manually. Automatic adjustment the existing instrument panel dimmer bus normally controls the pfd and m...

  • Page 57

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 45 system overview adjust key backlighting manually: 1) press the menu key on the pfd to display the pfd setup menu window. ‘auto’ becomes highlighted to the right of ‘pfd dspl’. Figure 1-33 manual key lighting adjustment 2) turn t...

  • Page 58

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 46 system overview b lank p age.

  • Page 59

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 47 flight instruments section 2 flight instruments warning: in the event that the airspeed, altitude, or heading indications become unusable, refer to the backup instruments. Increased situational awareness is provided by replacing...

  • Page 60

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 48 flight instruments 9 17 14 13 12 1 18 20 21 10 6 2 3 4 16 11 15 19 22 8 1 nav frequency box 2 airspeed indicator 3 current heading 4 groundspeed 5 power situation indicator (psi) 6 selected heading bug 7 dual tachometer 8 outside...

  • Page 61

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 49 flight instruments 6 8 7 2 4 3 1 5 9 10 1 traffic annunciation 2 radar altimeter 3 selected heading 4 wind data 5 dme information window 6 bearing information windows 7 barometric minimum descent altitude 8 flight plan window 9 ...

  • Page 62: 2.1  Flight Instruments

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 50 flight instruments 2.1 flight instruments airspeed indicator note: refer to the rotorcraft flight manual (rfm) for speed criteria. The airspeed indicator displays airspeed on a moving tape rolling number gauge. The groundspeed is...

  • Page 63: Attitude Indicator

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 51 flight instruments attitude indicator attitude information is displayed over a virtual blue sky and brown ground with a white horizon line. The attitude indicator displays the pitch, roll, and slip/skid information. 1 roll point...

  • Page 64: Altimeter

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 52 flight instruments altimeter the altimeter displays 600 feet of barometric altitude values at a time on a moving tape rolling number gauge. Numeric labels and major tick marks are shown at intervals of 100 feet. Minor tick marks ...

  • Page 65

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 53 flight instruments the barometric pressure setting is displayed below the altimeter in inches of mercury (in hg) or hectopascals (hpa) when metric units are selected. Adjusting the altimeter barometric setting creates discontinu...

  • Page 66

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 54 flight instruments a baro transition alert is provided to alert the pilot to change the barometric pressure setting when crossing the transition altitude in either direction. This is displayed by the flashing light blue barometri...

  • Page 67: Vertical Deviation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 55 flight instruments vertical deviation note: the glidepath indicator is only shown for aircraft with gia 63w integrated avionics units when sbas is available. The vertical deviation indicator (vdi) is a magenta chevron indicating...

  • Page 68

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 56 flight instruments horizontal situation indicator (hsi) the horizontal situation indicator (hsi) displays a rotating compass card in a heading-up orientation. Letters indicate the cardinal points and numeric labels occur every 30...

  • Page 69

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 57 flight instruments the arc hsi is a 140˚ expanded section of the compass rose. The arc hsi contains a course pointer, combined to/from indicator and a sliding deviation indicator, and a deviation scale. Upon station passage, the...

  • Page 70

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 58 flight instruments navigation angles (track, heading, course, bearing) are set on the aux - system setup page and are either corrected to the computed magnetic variation (‘mag var’), referenced to true north (denoted ‘t’), or cor...

  • Page 71

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 59 flight instruments turn rate indicator the turn rate indicator is located directly above the rotating compass card. Tick marks to the left and right of the lubber line denote half-standard and standard turn rates. A magenta turn...

  • Page 72

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 60 flight instruments when a bearing pointer is displayed, its associated information window is also displayed. The bearing information windows (figure 2-22) are displayed to the lower sides of the hsi and display the following info...

  • Page 73

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 61 flight instruments heading preset mode heading preset mode allows ahrs to compute heading data without using the magnetic sensing device. If a magnet anomaly occurs (either due to interference or magnetometer failure), and headi...

  • Page 74

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 62 flight instruments course deviation indicator (cdi) note: during a heading change of greater than 105˚ with respect to the course, the cdi on the arc hsi switches to the opposite side of the deviation scale and displays reverse s...

  • Page 75

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 63 flight instruments changing navigation sources: 1) select the cdi softkey to change from gps to vor1 or loc1. This places the light blue tuning box over the nav1 standby frequency in the upper left corner of the pfd. 2) select t...

  • Page 76

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 64 flight instruments gps cdi scaling when gps is the selected navigation source, the flight plan legs are sequenced automatically and annunciations appear on the hsi for the flight phase. Flight phase annunciations are normally sho...

  • Page 77

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 65 flight instruments figure 2-29 automatic cdi scaling 2.0 nm enroute (oceanic if >200 nm from nearest airport) 0.3 nm missed approach 1.0 nm approach 1.0 nm terminal 1.0 nm terminal 0.3 nm departure cdi full-scale deflection refe...

  • Page 78

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 66 flight instruments figure 2-30 typical lnav and lnav+v approach cdi scaling 1.0 nm 2 nm 350 ft angle set by system 0.3 nm faf cdi full-scale deflection cdi scale is set to the smaller of 0.3 nm or an angle set by the system cdi s...

  • Page 79

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 67 flight instruments obs mode note: vnv is inhibited while automatic waypoint sequencing has been suspended. Enabling omni-bearing selector (obs) mode suspends the automatic sequencing of waypoints in a gps flight plan (gps must b...

  • Page 80

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 68 flight instruments as the aircraft crosses the missed approach point (map), automatic approach waypoint sequencing is suspended. ‘susp’ appears on the hsi at the lower right of the aircraft symbol. The obs softkey label changes t...

  • Page 81: Temperature Displays

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 69 flight instruments 2.2 supplemental flight data note: selecting the dflts softkey turns off metric altimeter display, the inset map, and wind data display. In addition to the flight instruments, the pfd also displays various sup...

  • Page 82: Wind Data

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 70 flight instruments wind data wind direction and speed (relative to the aircraft) in knots can be displayed in a window to the upper left of the hsi. When the window is selected for display, but wind information is invalid or unav...

  • Page 83

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 71 flight instruments vertical navigation (vnv) indications when a vnv flight plan has been activated, vnv indications (vnv target altitude, rsvi, vdi) appear on the pfd in conjunction with the “tod within 1 minute” message and “ve...

  • Page 84: System Alerting

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 72 flight instruments 2.3 pfd annunciations and alerting functions the following annunciations and alerting functions are displayed on the pfd. Refer to the engine indication and crew alerting system (eicas) section for information ...

  • Page 85: Traffic Annunciation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 73 flight instruments traffic annunciation traffic is displayed symbolically on the pfd inset map, the mfd navigation map page, and various other mfd page maps. Refer to the hazard avoidance section and the appendix for more detail...

  • Page 86: Altitude Alerting

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 74 flight instruments altitude alerting the altitude alerting function provides visual and audio alerts when approaching the selected altitude. Whenever the selected altitude is changed, altitude alerting is reset. Altitude alerting...

  • Page 87

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 75 flight instruments minimum descent altitude/decision height alerting for altitude awareness, a minimum descent altitude (mda) or decision height (dh), based on barometric altitude or radar altitude, can be set. When active, the ...

  • Page 88: Radar Altimeter

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 76 flight instruments radar altimeter when the radar height (the aircraft altitude above ground level detected by the radar altimeter) is between zero and 2500 feet, the current value is displayed in green above the selected course ...

  • Page 89

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 77 flight instruments a ground line (figure 2-49) is shown on the altimeter to display the aircraft’s height relative to the ground. If the data becomes invalid, the message “ra fail” is displayed in yellow in place of the current ...

  • Page 90: 2.4  Abnormal Operations

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 78 flight instruments 2.4 abnormal operations abnormal gps conditions the annunciations listed in table 2-3 can appear on the hsi when abnormal gps conditions occur. Refer to the flight management section for more information on dea...

  • Page 91: Unusual Attitudes

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 79 flight instruments unusual attitudes when the aircraft enters an unusual pitch attitude, red chevrons pointing toward the horizon warn of extreme pitch. The chevrons are displayed on the attitude indicator, starting at 50˚ above...

  • Page 92

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev a 80 flight instruments b lank p age.

  • Page 93

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 81 engine indication & crew alerting system section 3 engine and crew alerting systems note: refer to the rotorcraft flight manual (rfm) for limitations. The g1000h integrated flight deck offers improved flight operations and reduc...

  • Page 94

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 82 engine indication & crew alerting system in a display fails, the other display may be configured to present primary flight display (pfd) symbology together with condensed eis information (refer to the system overview for more in...

  • Page 95

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 83 engine indication & crew alerting system 3.1 engine indication system (eis) strip note: depictions of equipment may differ from the installed equipment. Examples shown may differ from the actual aircraft configuration. Eis infor...

  • Page 96

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 84 engine indication & crew alerting system 9 7 8 10 5 3 4 2 1 figure 3-3 mfd eis strip (normal) 6 10 7 8 5 4 3 2 1 figure 3-4 eis strip (reversionary) 6.

  • Page 97: Power Situation Indicator

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 85 engine indication & crew alerting system 3.2 engine power and speed indications note: refer to the rotorcraft flight manual (frm) for engine operating limitations and corrective actions. The power situation indicator (psi) and d...

  • Page 98: Dual Tachometer

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 86 engine indication & crew alerting system takeoff timer after the engine has been started, if q or mgt are within the takeoff limitation ranges, the g1000h displays a 5-minute countdown timer inside the psi gauge. The timer flash...

  • Page 99: 3.3  Engine Page

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 87 engine indication & crew alerting system 3.3 engine page note: refer to the rotorcraft flight manual (frm) for engine operating limitations and corrective actions. Pressing the engine softkey on the mfd accesses the eis - engine...

  • Page 100: Power Assurance Check

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 88 engine indication & crew alerting system power assurance check the g1000h can assist the pilot in performing a power assurance check to determine if installed specification power can be achieved. Note: follow the procedures in t...

  • Page 101

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 89 engine indication & crew alerting system 3.4 crew alerting system (cas) note: aural alerts associated with abnormal conditions and advisories are managed through the audio panels. Refer to the audio panel and cns section for mor...

  • Page 102: Cas Message Prioritization

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 90 engine indication & crew alerting system mfd alerts window containing cas messages cas scrolling softkeys (disabled until more than 19 messages are displayed) figure 3-10 engine page cas display (mfd) cas message prioritization ...

  • Page 103

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 91 engine indication & crew alerting system note: see the rotorcraft flight manual (rfm) for recommended pilot actions. Annunciation text description audio alert battery hot battery overheat detected. Single chime engine fire fire/...

  • Page 104

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 92 engine indication & crew alerting system annunciation text description audio alert q miscomp q miscompare event. Single ping r/fuel boost right fuel boost pump has failed. R/fuel xfr right fuel transfer pump has failed. T/r chip...

  • Page 105: 4.1 Overview

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 93 audio panel and cns section 4 audio panel and cns 4.1 overview the communication/navigation/surveillance (cns) system includes the audio panel, communication radios, navigation radios, and mode s transponder. The system overview...

  • Page 106

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 94 audio panel and cns mfd/pfd controls and frequency display figure 4-1 mfd/pfd controls, nav/com frequency tuning boxes, and dme tuning window 12 3 4 5 9 10 11 7 8 6 1 2.

  • Page 107

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 95 audio panel and cns 1 nav vol/id knob – controls nav audio volume level. Press to turn the morse code identifier audio on and off. Volume level is shown in the nav frequency field as a percentage. 2 nav frequency transfer key – ...

  • Page 108: Audio Panel Controls

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 96 audio panel and cns audio panel controls figure 4-2 gma 350h audio panel controls 21 14 15 17 12 13 11 19 20 18 16 10 8 6 4 2 3 5 7 9 1 note: when a key is selected, a triangular annunciator above the key is illuminated. 1 mkr/m...

  • Page 109

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 97 audio panel and cns 12 mic1 – selects the #1 transmitter for transmitting. Com1 receive is simultaneously selected when this key is pressed allowing received audio from the #1 com receiver to be heard. Com2 or com3 receive can b...

  • Page 110: 4.2  Com Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 98 audio panel and cns 4.2 com operation com transceiver selection and activation note: when turning on the system for use, the system remembers the last frequencies used and the active com transceiver state prior to shutdown. The ...

  • Page 111

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 99 audio panel and cns transmit/receive indications during com transmission, a white tx appears by the active com frequency replacing the frequency transfer arrow. On the audio panel, when ptt is pressed, the active transceiver mic...

  • Page 112

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 100 audio panel and cns selecting the radio to be tuned press the small com knob to transfer the frequency tuning box and frequency transfer arrow between the upper and lower radio frequency fields. Figure 4-6 switching com tuning ...

  • Page 113

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 101 audio panel and cns auto-tuning the com frequency com frequencies can be automatically tuned from the following: •nearestairportswindow(pfd) •wpt–airportinformationpage •nrst–nearestairportspage •nrst–nearestfrequenciespage(art...

  • Page 114

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 102 audio panel and cns auto-tuning from the mfd frequencies can be automatically loaded into the com frequency box from pages in the nrst or wpt page group by highlighting the frequency and pressing the ent key (figures 4-9, 4-10,...

  • Page 115

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 103 audio panel and cns on the wpt - airport information page, the cursor can be placed on the frequency field by pressing the fms knob and scrolling through the list. The frequency is transferred to the com standby field with the ...

  • Page 116

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 104 audio panel and cns com frequencies can also be auto-tuned from the nrst – nearest airspaces, nrst – nearest frequencies, and nrst – nearest airports pages on the mfd in a similar manner using the appropriate softkeys or menu k...

  • Page 117: Frequency Spacing

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 105 audio panel and cns frequency spacing the com radios can tune either 25-khz spacing (118.000 to 136.975 mhz) or 8.33-khz spacing (118.000 to 136.990 mhz) for 760-channel or 3040-channel configuration. When 8.33-khz channel spac...

  • Page 118: Automatic Squelch

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 106 audio panel and cns automatic squelch automatic com squelch quiets unwanted static noise when no audio signal is received, while still providing good sensitivity to weak com signals. To disable automatic com squelch, press the ...

  • Page 119: 4.3  Nav Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 107 audio panel and cns 4.3 nav operation nav radio selection and activation the nav frequency box is composed of four fields; two standby fields and two active fields. The active frequencies are on the right side and the standby f...

  • Page 120: Nav Receiver Manual Tuning

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 108 audio panel and cns nav radios are selected for listening by pressing the corresponding keys on the audio panel. Pressing the nav1,or nav2 key selects and deselects the navigation radio source. Selected audio can be heard over ...

  • Page 121

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 109 audio panel and cns selecting the radio to be tuned press the small nav knob to transfer the frequency tuning box and frequency transfer arrow between the upper and lower radio frequency fields. Figure 4-20 switching nav tuning...

  • Page 122

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 110 audio panel and cns auto-tuning a nav frequency from the mfd nav frequencies can be selected and loaded from the following mfd pages: •wpt–airportinformation •wpt–vorinformation •nrst–nearestairports •nrst–nearestvor •nrst–near...

  • Page 123

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 111 audio panel and cns or : 1) when on the nearest vor, nearest airspaces, and nearest airports pages, press the menu key to display the page menu. 2) turn the large fms knob to scroll through the menu options. 3) press the ent ke...

  • Page 124

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 112 audio panel and cns in the example shown, the vor list is selected with the vor softkey or from the page menu. The fms knob or ent key is used to scroll through the list. The cursor is placed on the frequency with the freq soft...

  • Page 125

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 113 audio panel and cns while enroute, nav frequencies can also be auto-tuned from the nrst – nearest airports, wpt – airport information, wpt – vor information, and nrst – nearest frequencies pages on the mfd in a similar manner u...

  • Page 126

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 114 audio panel and cns auto-tuning nav frequencies on approach activation note: the primary nav frequency is auto-tuned upon loading a vor or ils/localizer approach. Note: when an ils/loc approach has been activated while navigati...

  • Page 127

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 115 audio panel and cns marker beacon receiver (optional) note: the marker beacon indicators operate independently of marker beacon audio and cannot be turned off. The marker beacon receiver is used as part of the ils. The marker b...

  • Page 128: Dme Tuning (Optional)

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 116 audio panel and cns dme tuning (optional) note: when another auxiliary window is turned on, the dme tuning window is replaced on the pfd. Note: when turning on the system for use, the system remembers the last frequency used fo...

  • Page 129: Transponder Controls

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 117 audio panel and cns 4.4 gtx 33 mode s transponder the gtx 33 mode s transponder provides mode a, mode c, and mode s interrogation and reply capabilities. Selective addressing or mode select (mode s) capability includes the foll...

  • Page 130: Transponder Mode Selection

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 118 audio panel and cns figure 4-30 transponder softkeys (pfd) pressing the back softkey returns to the top-level softkeys. Alerts alerts back bksp ident 7 6 5 4 3 2 1 0 stby on alt vfr code ident back xpdr ident pressing the back ...

  • Page 131

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 119 audio panel and cns standby mode (manual) note: in standby mode, the ident function is inoperative. Standby mode can be selected at any time by pressing the stby softkey. In standby, the transponder does not reply to interrogat...

  • Page 132

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 120 audio panel and cns altitude mode (automatic or manual) altitude mode is automatically selected when the aircraft becomes airborne. Altitude mode may also be selected manually by pressing the alt softkey. If altitude mode is se...

  • Page 133: Entering A Transponder Code

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 121 audio panel and cns entering a transponder code entering a transponder code with softkeys: 1) press the xpdr softkey to display the transponder mode selection softkeys. 2) press the code softkey to display the transponder code ...

  • Page 134: Ident Function

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 122 audio panel and cns vfr code the vfr code can be entered either manually or by pressing the xpdr softkey, then the vfr softkey. When the vfr softkey is pressed, the pre-programmed vfr code is automatically displayed in the code...

  • Page 135: Power-Up

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 123 audio panel and cns 4.5 additional audio panel functions power-up the audio panel performs a self-test during power-up. During the self-test all audio panel annunciator lights illuminate for approximately two seconds. Once the ...

  • Page 136

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 124 audio panel and cns intercom modes note: in the following modes the copilot position is configured as crew. Note: in the default ics configuration, only the pilot and copilot positions can hear aircraft alerts. Note: when in sp...

  • Page 137

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 125 audio panel and cns p assenger /c rew i solate m ode in ‘passenger/crew isolate’ mode the pilot and copilot hear the aircraft audio and each other. The passengers hear each other. Ics keys mode operation aircraft audio coplt pi...

  • Page 138

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 126 audio panel and cns p ilot & c opilot i solate m ode in ‘pilot & copilot isolate’ mode the pilot, copilot, and passengers hear the aircraft audio. The passengers hear each other. The copilot has the option to use split-com mode...

  • Page 139

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 127 audio panel and cns intercom volume and squelch the vol/crsr knob controls selection and volume or manual intercom squelch adjustment for audio sources that may not be adjustable anywhere else in the system. The small knob cont...

  • Page 140

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 128 audio panel and cns selecting any button other than pilot, coplt, pass , music or will cancel blue-select mode. Pressing the small knob will also cancel blue-select mode. After approximately ten seconds with no input, the blue-...

  • Page 141

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 129 audio panel and cns clearance recorder and player (optional) the audio panel contains a digital clearance recorder that records up to 2.5 minutes of the selected com radio signal. Recorded com audio is stored in separate memory...

  • Page 142: Split Com

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 130 audio panel and cns split com note: split com performance is affected by the distance between the com antennas and the separation of the tuned frequencies. If the selected com frequencies are too close together, interference ma...

  • Page 143: Entertainment Inputs

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 131 audio panel and cns entertainment inputs the audio panel provides controls for one stereo music input and one stereo telephone/entertainment input. 1. The telephone/enterrainment ( ) key controls a telephone or entertainment de...

  • Page 144

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 132 audio panel and cns 4.6 audio panel preflight procedure note: if the pilot and/or copilot are using headsets that have a high/low switch or volume control knob, verify that the switch is in the high position and the volume cont...

  • Page 145: 4.7  Abnormal Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 133 audio panel and cns 4.7 abnormal operation abnormal operation of the system includes equipment failures of the system components and failure of associated equipment, including switches and external devices. Stuck microphone if ...

  • Page 146

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 134 audio panel and cns.

  • Page 147: 5.1 Introduction

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 135 flight management section 5 flight management 5.1 introduction the g1000h is an integrated flight, engine, communication, navigation and surveillance system. This section of the pilot’s guide explains flight management using th...

  • Page 148: Navigation Status Box

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 136 flight management figure 5-1 gps navigation information on the pfd location of: - inset map - direct to window - flight plan window - procedures window - nearest airports window navigation status box navigation mode figure 5-2 ...

  • Page 149

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 137 flight management •activeflightplanleg(e.G.,‘d->kict’or‘kixd-> kcos’) or flight plan annunciations (e.G., ‘turn right to 021˚ in 8 seconds’) •distance (dis) and bearing (brg) to the next waypoint or flight plan annunciations (e...

  • Page 150: 5.2  Using Map Displays

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 138 flight management 5.2 using map displays map displays are used extensively in the system to provide situational awareness in flight. Most system maps can display the following information: •airports, navaids, airspaces, airways...

  • Page 151

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 139 flight management note: when panning or reviewing active flight plan legs in a non-north up orientation, the map does not show the map orientation nor the wind direction and speed. Note: map orientation can only be changed on t...

  • Page 152: Map Range

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 140 flight management map range there are 28 different map ranges available, from 500 feet to 2000 nm. The current range is indicated in the lower right corner of the map and represents the top-to-bottom distance covered by the map...

  • Page 153

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 141 flight management •the‘timeout’time(configurableonthemapsetuppageforthemapgroup)determineshowlongauto zoom is overridden by a manual adjustment of the range knob. At the expiration of this time, the auto zoom range is restored....

  • Page 154: Map Panning

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 142 flight management map panning map panning allows the pilot to: •viewpartsofthemapoutsidethedisplayedrangewithoutadjustingthemaprange •highlightandselectlocationsonthemap •reviewinformationforaselectedairport,navaidoruserwaypoin...

  • Page 155

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 143 flight management when the map pointer is placed on an object, the name of the object is highlighted (even if the name was not originally displayed on the map). When any map feature or object is selected on the map display, per...

  • Page 156

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 144 flight management when the map pointer crosses an airspace boundary, the boundary is highlighted and airspace information is shown at the top of the display. The information includes the name and class of airspace, the ceiling ...

  • Page 157

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 145 flight management reviewing information for an airport, navaid, or user waypoint: 1) place the map pointer on a waypoint. 2) press the ent key to display the waypoint information page for the selected waypoint. 3) press the go ...

  • Page 158

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 146 flight management viewing airspace information for a special-use or controlled airspace: 1) place the map pointer on an open area within the boundaries of an airspace. 2) press the ent key to display an options menu. 3) ‘review...

  • Page 159

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 147 flight management measuring bearing and distance distance and bearing from the aircraft’s present position to any point on the viewable navigation map may be calculated using the ‘measure bearing and distance’ selection from na...

  • Page 160: Topography

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 148 flight management topography all navigation maps can display various shades of topography colors representing land elevation, similar to aviation sectional charts. Topographic data can be displayed or removed as described in th...

  • Page 161

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 149 flight management figure 5-15 navigation map setup menu - topo data setup topo data on/off topo data range the topographic data range is the maximum map range on which topographic data is displayed. Note: since the pfd inset ma...

  • Page 162

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 150 flight management figure 5-16 navigation map - topo scale maximum displayed elevation minimum displayed elevation aircraft altitude (msl) ground elevation at map pointer location (only visible when map pointer is displayed) ran...

  • Page 163: Map Symbols

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 151 flight management map symbols this section discusses the types of land and aviation symbols that can be displayed. Each listed type of symbol can be turned on or off, and the maximum range to display each symbol can be set. The...

  • Page 164

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 152 flight management aviation symbols the following items are configured on the aviation menu: aviation symbols (text label size can be none, small, medium (med), or large (lrg)) symbol default range (nm) maximum range (nm) active...

  • Page 165

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 153 flight management symbol setup all pages with maps can display land symbols (roads, lakes, borders, etc). Land symbols can be removed totally (turned off). Displaying/removing all land symbols: 1) press the menu key with the na...

  • Page 166

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 154 flight management figure 5-19 navigation map setup menu - land group setup maximum display range text label size (none, small, med, or lrg) figure 5-20 navigation map setup menu - aviation group setup maximum display range text...

  • Page 167

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 155 flight management map declutter the declutter feature allows the pilot to progressively step through four levels of removing map information. The declutter level is displayed in the dcltr softkey and next to the declutter menu ...

  • Page 168

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 156 flight management table 5-3 lists the items displayed at each declutter level. The ‘x’ represents map items displayed for the various levels of declutter. Item no declutter declutter-1 declutter-2 declutter-3 flight plan route ...

  • Page 169: Airways

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 157 flight management airways this airways discussion is based upon the north american airway structure. The airway structure in places other than north america vary by location, etc. And are not discussed in this book. Low altitud...

  • Page 170

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 158 flight management airways may be displayed on the map at the pilot’s discretion using either a combination of airways softkey presses, or menu selections using the menu key from the navigation map page. The airway range can als...

  • Page 171: Track Vector

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 159 flight management the following range items are configurable on the airways menu: airway type symbol default range (nm) maximum range (nm) low altitude airway (low alt airway) 200 500 high altitude airway (hi alt airway) 300 50...

  • Page 172: Wind Vector

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 160 flight management figure 5-25 navigation map setup menu -track vector, wind vector, nav range ring, fuel range ring setup track vector - on/off - look ahead time fuel range - on/off - fuel reserve time wind vector on/off nav ra...

  • Page 173: Nav Range Ring

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 161 flight management nav range ring the nav range ring shows the direction of travel (ground track) on a rotating compass card. The range is determined by the map range. The range is 1/4 of the map range (e.G., 37.5 nm on a 150 nm...

  • Page 174: Fuel Range Ring

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 162 flight management fuel range ring the map can display a fuel range ring which shows the remaining flight distance. A dashed green circle indicates the selected range to reserve fuel. A solid green circle indicates the total end...

  • Page 175: Field Of View (Svs)

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 163 flight management field of view (svs) the map can display the boundaries of the pfd synthetic vision system (svs) lateral field of view. The field of view is shown as two dashed lines forming a v shape in front of the aircraft ...

  • Page 176: 5.3 Waypoints

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 164 flight management 5.3 waypoints waypoints are predetermined geographical positions (internal database) or pilot-entered positions, and are used for all phases of flight planning and navigation. Communication and navigation freq...

  • Page 177: Airports

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 165 flight management figure 5-31 waypoint information window - duplicate identifier duplicate message identifier with duplicates duplicate waypoints airports note: ‘north up’ orientation on the airport information page cannot be c...

  • Page 178

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 166 flight management figure 5-32 airport information page airport/runway diagram navigation map showing selected airport runway information - designation - length/width/surface - lighting available airport information - id/facilit...

  • Page 179

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 167 flight management figure 5-33 airport directory page example airport information - id/facility/city - usage type/region airport directory information softkeys the aopa directory information is viewed on the airport directory pa...

  • Page 180

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 168 flight management selecting an airport for review by identifier, facility name, or location: 1) from the airport information page, press the fms knob. 2) use the fms knobs and enter an identifier, facility name, or location. 3)...

  • Page 181

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 169 flight management figure 5-34 nearest airports window on pfd com freq. Info. - identification - frequency airport identifier/ type length of longest runway approach available additional airports (within 200 nm) nrst softkey bea...

  • Page 182

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 170 flight management if there are no items for display in a boxed area, text indicating that fact is displayed. The currently selected airport remains in the list until it is unselected. Figure 5-36 nearest airport page nearest ai...

  • Page 183

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 171 flight management viewing runway information for a specific airport: 1) with the nearest airports page displayed, press the rnwy softkey; or press the menu key, highlight ‘select runway window’; and press the ent key. The curso...

  • Page 184: Intersections

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 172 flight management intersections note: the vor displayed on the intersection information page is the nearest vor, not necessarily the vor used to define the intersection. The intersection information page is used to view informa...

  • Page 185

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 173 flight management the selected intersection is indicated by a white arrow. Up to eleven intersections are visible at a time. If there are more than can be shown, the list can be scrolled. If there are no items for display, text...

  • Page 186: Ndb

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 174 flight management ndb s the ndb information page is used to view information about ndbs. In addition to displaying a map of the currently selected ndb and surrounding area, the page displays ndb information in four boxes labele...

  • Page 187

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 175 flight management the nearest ndb page can be used to quickly find a ndb close to the flight path. In addition to displaying a map of the surrounding area, the page displays information for up to 25 nearest ndbs in three boxes ...

  • Page 188: Vor

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 176 flight management vor s the vor information page can be used to view information about vor and ils signals (since ils signals can be received on a nav receiver), or to quickly auto-tune a vor or ils frequency. Localizer informa...

  • Page 189

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 177 flight management 1) with the nearest vor page displayed, press the menu key. 2) highlight ‘select vor window’, and press the ent key. 3) press the ent key or turn either fms knob to select an identifier in the nearest vor box....

  • Page 190: User Waypoints

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 178 flight management user waypoints the system can create and store up to 1,000 user-defined waypoints. User waypoints can be created from any map page (except pfd inset map, aux-trip planning page, or procedure pages) by selectin...

  • Page 191

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 179 flight management figure 5-45 nearest user waypoint page selected user waypoint navigation map showing selected user waypoint nearest user wpt list - identifier - bearing/distance from aircraft position user waypoint info - com...

  • Page 192

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 180 flight management or : 1) press the fms knob to activate the cursor. 2) enter a user waypoint name (up to six characters). 3) press the ent key. The message ‘are you sure you want to create the new user waypoint aaaaaa?’ is dis...

  • Page 193

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 181 flight management 3) enter a user waypoint name (up to six characters). 4) press the ent key to accept the selected name. The first reference waypoint box is highlighted. 5) if desired, define the type and location of the waypo...

  • Page 194

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 182 flight management changing the location of an existing waypoint to the aircraft present position: 1) enter a waypoint name or select the waypoint in the user waypoint list, then press the ent key. 2) press the menu key. 3) sele...

  • Page 195

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 183 flight management deleting user waypoints deleting a single user waypoint: 1) highlight a user waypoint in the user waypoint list, or enter a waypoint in the user waypoint field. 2) press the delete softkey or press the clr key...

  • Page 196: 5.4 Airspaces

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 184 flight management 5.4 airspaces the system can display the following types of airspaces: class b/tma, class c/tca, class d, restricted, moa (military), other airspace, air defense interdiction zone (adiz), and temporary flight ...

  • Page 197

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 185 flight management navigation map page. It simply turns on/off the warning provided when the aircraft is approaching or near an airspace. An altitude buffer is also provided which “expands” the vertical range above or below an a...

  • Page 198

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 186 flight management map ranges for the airspace boundaries are selected from the aviation group in the map setup menu. See table 5-2 for the default and maximum ranges for each type of airspace and the symbol used to define the a...

  • Page 199

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 187 flight management pressing the pfd alerts softkey displays the message window on the pfd. The following airspace alerts are displayed in the message window: message comments inside arspc – inside airspace. The aircraft is insid...

  • Page 200: 5.5  Direct-to-Navigation

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 188 flight management 5.5 direct-to-navigation the direct-to method of navigation, initiated by pressing the direct-to key on either the mfd or pfd, is quicker to use than a flight plan when the desire is to navigate to a single po...

  • Page 201

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 189 flight management any waypoint can be entered as a direct-to destination from the direct-to window. Entering a waypoint identifier, facility name, or city as a direct-to destination: 1) press the direct-to key. The direct-to wi...

  • Page 202

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 190 flight management any nrst, recent, user, or airway waypoints can be selected as a direct-to destination in the direct-to window. Selecting a nrst, recent, user, or airway waypoint as a direct-to destination: 1) press the direc...

  • Page 203

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 191 flight management 3) if the pointer is placed on an existing airport, navaid, or user waypoint, the waypoint name is highlighted. 4) press the direct-to key to display the direct-to window with the selected point entered as the...

  • Page 204

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 192 flight management when navigating a direct-to, the system sets a direct great circle course to the selected destination. The course to a destination can also be manually selected using the course field (‘course’) on the direct-...

  • Page 205

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 193 flight management removing a vnv altitude constraint: 1) press the direct-to key to display the direct-to window. 2) press the menu key. 3) with ‘clear vertical constraints’ highlighted, press the ent key. Figure 5-54 direct-to...

  • Page 206: 5.6  Flight Planning

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 194 flight management 5.6 flight planning flight planning on the system consists of building a flight plan by entering waypoints one at a time, adding waypoints along airways, and inserting departures, airways, arrivals, or approac...

  • Page 207: Flight Plan Creation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 195 flight management the following could cause the airway update to fail: •airwayidentifier,entrywaypointorexitwaypointnotfoundinthenewdatabase. •airwayentry/exitwaypointisnotanacceptablewaypointfortheairway–eitherthewaypointisnol...

  • Page 208

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 196 flight management active flight plan comment figure 5-56 active flight plan window on pfd active flight plan leg active flight plan waypoint list - waypoint id - desired track to waypoint - distance to waypoint - airway identif...

  • Page 209

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 197 flight management creating an active flight plan: 1) press the fpl key. 2) press the fms knob to activate the cursor (only on mfd). 3) turn the small fms knob to display the waypoint information window. (turning it clockwise di...

  • Page 210

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 198 flight management flight plans can be imported from an sd card or exported to an sd card from the stored flight plan page. Importing a flight plan from an sd card 1) insert the sd card containing the flight plan in the top card...

  • Page 211

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 199 flight management note: if the imported flight plan contains a waypoint with a name that duplicates the name of a waypoint already stored on the system, the system compares the coordinates of the imported waypoint with those of...

  • Page 212

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 200 flight management adding waypoints to an existing flight plan waypoints can be added to the active flight plan or any stored flight plan. Choose the flight plan, select the desired point of insertion, enter the waypoint, and it...

  • Page 213

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 201 flight management adding a waypoint to a stored flight plan: 1) on the flight plan catalog page, press the fms knob to activate the cursor. 2) highlight the desired flight plan. 3) press the edit softkey; or press the ent key, ...

  • Page 214

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 202 flight management creating and adding user waypoints to the active flight plan: 1) press the joystick to activate the panning function on the active flight plan page and pan to the map location of the desired user waypoint. 2) ...

  • Page 215

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 203 flight management 5) turn the fms knob to select the desired airway from the list, and press the ent key. Low altitude airways are shown first in the list, followed by “all” altitude airways, and then high altitude airways. 6) ...

  • Page 216

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 204 flight management restrictions on adding airways some airways have directional restrictions on all or part of the route. Airway “a2” in europe has a directional restriction over the whole route such that it can be flown only in...

  • Page 217

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 205 flight management departure (dp) a departure procedure (dp) is loaded at the departure airport in the flight plan. Only one departure can be loaded at a time in a flight plan. The route is defined by selection of a departure, t...

  • Page 218

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 206 flight management figure 5-68 departure loading page - selecting transition departure airport selected departure departure transition points available selected runway selected departure end point preview of selected departure s...

  • Page 219

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 207 flight management arrival (star) a standard terminal arrival (star) is loaded at the destination airport in the flight plan. Only one arrival can be loaded at a time in a flight plan. The route is defined by selection of an arr...

  • Page 220

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 208 flight management figure 5-71 arrival loading page - selecting the transition destination airport selected arrival transitions available with dbry1 arrival waypoint sequence preview of selected arrival selected transition figur...

  • Page 221

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 209 flight management approach (appr) an approach procedure (appr) can be loaded at any airport that has an approach available. Only one approach can be loaded at a time in a flight plan. The route for a selected approach is define...

  • Page 222

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 210 flight management figure 5-74 approach loading page - selecting the transition destination airport selected approach transitions available with selected approach approach waypoint sequence preview of selected approach load appr...

  • Page 223: Flight Plan Storage

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 211 flight management flight plan storage the system can store up to 99 flight plans, numbered 1 through 99. The active flight plan is erased when the system is powered off or when another flight plan is activated. Details about ea...

  • Page 224

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 212 flight management sort flight plans the stored flight plans can be sorted alphanumerically based on the flight plan name (comment) assigned to each flight plan. Sorting by flight plan name (comment): 1) press the fpl key and tu...

  • Page 225: Flight Plan Editing

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 213 flight management 3) select the copy softkey; or press the menu key, highlight ‘copy flight plan’, and press the ent key. The ‘copy to flight plan xx?’ window is displayed. 4) with ‘ok’ highlighted, press the ent key to copy th...

  • Page 226

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 214 flight management deleting flight plan items individual waypoints, entire airways, and entire procedures can be deleted from a flight plan. Some waypoints in the final approach segment (such as the faf or map) can not be delete...

  • Page 227

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 215 flight management deleting an individual waypoint from a stored flight plan: 1) press the fpl key to display the active flight plan page. 2) turn the small fms knob clockwise one click to display the flight plan catalog page. 3...

  • Page 228: Along Track Offsets

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 216 flight management 1) press the fpl key to display the active flight plan page. 2) turn the small fms knob clockwise one click to display the flight plan catalog page. 3) press the fms knob to activate the cursor and turn the fm...

  • Page 229

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 217 flight management entered from 1 to 99 nm in increments of 1 nm. Entering a negative offset distance results in an along track offset waypoint inserted before the selected waypoint, whereas entering a positive offset distance r...

  • Page 230: Parallel Track

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 218 flight management parallel track the parallel track (ptk) feature allows creation of a parallel course offset of 1 to 50 nm left or right of the current flight plan. When parallel track is activated, the course line drawn on th...

  • Page 231

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 219 flight management figure 5-79 parallel track window offset direction offset distance activation prompt figure 5-80 parallel track active parallel track waypoints - tifto-p - top-p - sln-p - hys-p - laa-p activating parallel tra...

  • Page 232

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 220 flight management if the parallel track proposed by the offset direction and distance is not allowed by the system, the activation prompt is displayed, but disabled. Parallel track cannot be activated if a course is set using d...

  • Page 233

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 221 flight management activating a flight plan leg the system allows selection of a highlighted leg as the “active leg” (the flight plan leg which is currently used for navigation guidance). Activating a flight plan leg: 1) press t...

  • Page 234: Inverting A Flight Plan

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 222 flight management figure 5-84 active flight plan page - new active leg new active flight plan leg confirmation window inverting a flight plan any flight plan may be inverted (reversed) for navigation back to the original depart...

  • Page 235: Flight Plan Views

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 223 flight management flight plan views information about flight plans can be viewed in more than one way. The active flight plan can be configured to show cumulative distance over the length of the flight plan or the distance for ...

  • Page 236

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 224 flight management figure 5-86 active flight plan - wide vs. Narrow view wide softkey, narrow softkey, leg-leg softkey, cum softkey active flight plan narrow view active flight plan wide view collapsing airways the system allows...

  • Page 237: Closest Point of Fpl

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 225 flight management figure 5-87 expanded/collapsed airways q3.Fepot airway collapsed view expanded view collapsing/expanding the airways in the active flight plan: 1) press the fpl key to display the active flight plan page (mfd)...

  • Page 238: 5.7  Vertical Navigation

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 226 flight management 5.7 vertical navigation note: the system supports vertical navigation for all lateral leg types except for ca, ci, fa, fm, ha, hm, pi, va, vd, vi, vr, and vm. Vertical constraints are not retained in stored fl...

  • Page 239

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 227 flight management canceling vertical navigation results in vertical deviation (v dev), vertical speed required (vs req), and time to top of descent/bottom of descent (time to tod/bod) going invalid. The vertical deviation indic...

  • Page 240: Altitude Constraints

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 228 flight management 4) press the ent key. Vertical guidance begins to the altitude constraint for the selected waypoint. 5) press the fms knob to remove the flashing cursor. The vertical navigation profile can be modified by dire...

  • Page 241

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 229 flight management white text light blue text light blue subdued text large text altitude calculated by the system estimating the altitude of the aircraft as it passes over the navigation point. This altitude is provided as a re...

  • Page 242

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 230 flight management an altitude constraint is invalid if: •meetingtheconstraintrequirestheaircrafttoclimb •meetingtheconstraintrequiresthemaximumflightpathangleormaximumverticalspeedtobeexceeded •thealtitudeconstraintresultsinato...

  • Page 243

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 231 flight management reverting a manually entered altitude constraint back to the navigation database value: 1) press the fpl key to display the active flight plan page on the mfd. 2) press the fms knob, and turn to highlight the ...

  • Page 244: 5.8 Procedures

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 232 flight management 5.8 procedures the system can access the whole range of instrument procedures available. Departures (dps), arrivals (stars), and non-precision and precision approaches (apprs) are stored within the database an...

  • Page 245

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 233 flight management figure 5-91 departure selection departure airport departure preview available procedure actions departure choices loaded procedures procedure loading page selection softkeys figure 5-92 departure loading loade...

  • Page 246

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 234 flight management viewing available departures at an airport: 1) from the airport information page (first page in the wpt group), select the dp softkey. The departure information page is displayed, defaulting to the airport dis...

  • Page 247: Arrivals

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 235 flight management arrivals a standard terminal arrival (star) can be loaded at any airport that has one available. Only one arrival can be loaded at a time in a flight plan. If an arrival is loaded when another arrival is alrea...

  • Page 248

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 236 flight management figure 5-94 arrival loading loaded arrival selected arrival procedure loading page selection softkeys viewing available arrivals at an airport: 1) from the airport information page (first page in the wpt group...

  • Page 249: Approaches

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 237 flight management removing an arrival from the active flight plan when plans change while flying ifr, arrivals can be easily removed from the active flight plan. Removing an arrival from the active flight plan: 1) press the fpl...

  • Page 250

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 238 flight management the system waas gps allows for flying lnav, lnav/vnav, and lpv approaches according to the published chart. Lnav+v is a standard lnav approach with advisory vertical guidance provided for assistance in maintai...

  • Page 251

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 239 flight management figure 5-95 approach selection destination airport approach preview available procedure actions approach choices loaded procedures figure 5-96 approach loading loaded approach selected approach load or activat...

  • Page 252

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 240 flight management viewing available approaches at an airport: 1) from the airport information page (first page in the wpt group), select the apr softkey. The approach information page is displayed, defaulting to the airport dis...

  • Page 253

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 241 flight management activating an approach a previously loaded approach can be activated from the procedures window. Activating a previously loaded approach: 1) press the proc key. The procedures window is displayed with ‘activat...

  • Page 254

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 242 flight management missed approach activating a missed approach in the active flight plan: press the go around button. Or : fly past the map, and press the susp softkey on the pfd. Or : 1) press the proc key. 2) turn the fms kno...

  • Page 255: 5.9  Trip Planning

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 243 flight management 5.9 trip planning the system allows the pilot to view trip planning information, fuel information, and other information for a specified flight plan or flight plan leg based on automatic data, or based on manu...

  • Page 256

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 244 flight management trip statistics the trip statistics are calculated based on the selected starting and ending waypoints and the trip planning inputs. In flight plan mode (fpl) with a stored flight plan selected (nn), and the e...

  • Page 257

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 245 flight management fuel statistics the fuel statistics are calculated based on the selected starting and ending waypoints and the trip planning inputs. Some of the calculated trip statistics are dashed when the selected leg of t...

  • Page 258

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 246 flight management selecting automatic or manual page mode: select the auto softkey or the manual softkey; or press the menu key, highlight ‘auto mode’ or ‘manual mode’, and press the ent key. Selecting flight plan or waypoint m...

  • Page 259: 5.10  Raim Prediction

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 247 flight management 5.10 raim prediction raim (receiver autonomous integrity monitoring) is a gps receiver function that performs a consistency check on all tracked satellites. Raim ensures that the available satellite geometry a...

  • Page 260

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 248 flight management 4) enter the identifier, facility, or city name of the departure waypoint; or select a waypoint from the submenu of waypoints and press the ent key to accept the waypoint entry. 5) turn the fms knobs to enter ...

  • Page 261

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 249 flight management figure 5-102 sbas display - active sbas softkey (displays sbas selection) sbas selection box - egnos enable/disable - msas enable/disable - waas enable/disable raim softkey (displays raim prediction) sbas stat...

  • Page 262

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 250 flight management figure 5-103 sbas display - disabled sbas softkey (displays sbas selection) sbas selection box - egnos enable/disable - msas enable/disable - waas enable/disable raim softkey (displays raim prediction) sbas st...

  • Page 263

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 251 flight management 5.11 navigating a flight plan the following discussion is an example of navigating a flight plan with the waas capable gps system while the system provides vertical guidance through descents. A lateral flight ...

  • Page 264

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 252 flight management 3) atc now assigns routing to join v4. A heading of 290º is assigned to intercept v4. The aircraft turns to heading 290° as seen in figure 5-105. Figure 5-105 assigned heading of 290º 4) enter v4 into the flig...

  • Page 265

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 253 flight management b) the desired entry point for v4 (top) must be entered. Turn the large fms knob to highlight the desired flight plan insertion point (sln) as shown in figure 5-106. When the v4 entry point (top) is inserted, ...

  • Page 266

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 254 flight management d) press the ent key. Top is inserted into the flight plan as in figure 5-108. Figure 5-108 top inserted into the flight plan e) with sln still highlighted as in figure 5-108, turn the small fms knob clockwise...

  • Page 267

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 255 flight management h) press the ent key. The list of available exits for v4 is now displayed as in figure 5-110. Figure 5-110 list of available exits for v4 i) if necessary, turn either fms knob to select the desired exit. In th...

  • Page 268

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 256 flight management l) v4 is now loaded into the flight plan as shown in figure 5-112. Figure 5-112 v4 is loaded in the flight plan 5) making v4 the active leg of the flight plan. A) press the fms knob to activate the cursor. B) ...

  • Page 269

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 257 flight management d) verify the displayed leg is the desired leg and press the ent key. Note in figure 5-114, the magenta arrow in the flight plan window and magenta line on the map indicating v4 is now the active flight plan l...

  • Page 270

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 258 flight management 7) as the cdi approaches center, the aircraft turns onto the active leg as seen in figure 5-115. Figure 5-115 turn on to active leg 8) at sln, victor airway 244 (v244) is intercepted. Turn prompts are displaye...

  • Page 271

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 259 flight management 9) as seen in figure 5-117, v244 is now the active flight plan leg. Figure 5-117 v244 now active leg.

  • Page 272

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 260 flight management 10) at lamar vor (laa) v263 is intercepted. See figure 5-118. Figure 5-118 hys to laa leg active 11) atc grants clearance to proceed direct to the opshn intersection to begin the arrival procedure. Atc advises...

  • Page 273

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 261 flight management d) turn the large fms knob to place the cursor in the vnv altitude field as shown in figure 5-120. Figure 5-120 enter vnv altitude e) an altitude of 10,000 feet is entered as requested by atc. F) press the ent...

  • Page 274

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 262 flight management h) press the ent key twice to activate the direct-to. Note, in figure 5-122, the magenta arrow indicating the direct- to opshn after the offset waypoint for opshn. The preceding offset waypoint indicates the o...

  • Page 275

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 263 flight management b) ‘select approach’ should be highlighted as shown in figure 5-123. Figure 5-123 procedures window c) press the ent key. A list of available approaches for the destination airport is displayed as in figure 5-...

  • Page 276

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 264 flight management e) press the ent key. A list of available transitions for the selected approach is displayed as in figure 5-125. Figure 5-125 list of available transitions f) turn either fms knob to select the desired transit...

  • Page 277

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 265 flight management figure 5-126 barometric minimums set i) with ‘load?’ highlighted, again press the ent key. The selected approach is added to the flight plan as seen in figure 5-127. Figure 5-127 loaded approach.

  • Page 278

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 266 flight management 13) note the altitude constraints associated with each of the approach waypoints as seen in figure 5-128. These altitudes are loaded from the database and are displayed as light blue text, indicating these val...

  • Page 279

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 267 flight management 14) as the aircraft approaches opshn, it may be desirable to adjust the speed, or steepness of the upcoming descent. The default flight path angle (fpa) is -3.0 degrees and a required vertical speed is compute...

  • Page 280

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 268 flight management 15) as seen in figure 5-130, the aircraft is approaching tod. Note the target vertical speed required to reach the selected altitude. The vertical deviation indicator (vdi) and the required vertical speed indi...

  • Page 281

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 269 flight management 16) upon reaching tod, a descent vertical speed is established by placing the vsi pointer in line with the rvsi as shown in figure 5-132. Figure 5-132 vdi & rvsi showing correctly established descent align act...

  • Page 282

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 270 flight management 18) the aircraft is approaching opshn. The upcoming turn and next heading are annunciated at the top left of the pfd as seen in figure 5-134. Initiate the turn and maneuver the aircraft on a track through the ...

  • Page 283

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 271 flight management 19) after passing opshn, the next leg of the arrival turns magenta as shown in figure 5-135. The magenta arrow in the flight plan list now indicates the opshn to fsher leg of the arrival procedure is now activ...

  • Page 284

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 272 flight management figure 5-136 approaching pynon.

  • Page 285

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 273 flight management 21) upon passing pynon the approach procedure automatically becomes active. The approach may be activated at any point to proceed directly to the iaf. In this example, the aircraft has progressed through the f...

  • Page 286

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 274 flight management 22) the iaf is the next waypoint. At the tod, establish a descent vertical speed as previously discussed in step 16. The aircraft altitude is 9,000 feet upon reaching habuk. Figure 5-139 descending turn to the...

  • Page 287

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 275 flight management 23) after crossing falur the next waypoint is the faf. The flight phase changes to lpv on the hsi indicating the current phase of flight is in approach mode and the approach type is lpv. Cdi scaling changes ac...

  • Page 288

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 276 flight management 24) after crossing cegix, the aircraft continues following the glidepath to maintain the descent to “at or above” 6,370 feet at the missed approach point (map) (rw35r) as seen in figure 5-141. Figure 5-141 des...

  • Page 289

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 277 flight management 25) upon reaching the map, it is decided to execute a missed approach. Automatic waypoint sequencing is suspended past the map. Press the go around button, or press the susp softkey on the pfd, to resume autom...

  • Page 290

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 278 flight management 26) the aircraft continues climbing to “at or above” 10,000 feet at mogal. A holding pattern is established at the mahp (mogal) as shown in figure 5-143. Figure 5-143 establishing the holding pattern 27) the a...

  • Page 291: 5.12  Abnormal Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 279 flight management 5.12 abnormal operation this section discusses the dead reckoning mode of operation and the subsequent indications. Note: dead reckoning mode only functions in enroute (enr) or oceanic (ocn) phase of flight. I...

  • Page 292

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 280 flight management distance & bearing gps navigation lost message dead reckoning annunciaion figure 5-145 dead reckoning mode - gps derived data shown in yellow dead reckoning annunciation subdued rotorcraft symbol nav data bar ...

  • Page 293: 6.1  Xm Satellite Weather

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 281 hazard avoidance section 6 hazard avoidance the g1000h hazard avoidance features are designed to provide advisory information of potential hazards to flight safety associated with weather, terrain, and air traffic. This section...

  • Page 294

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 282 hazard avoidance xm satellite radio uses the coded ids to send an activation signal that allows the system to display weather data and/or entertainment programming provided through the gdl 69ah. Activating xm satellite weather ...

  • Page 295

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 283 hazard avoidance using xm satellite weather products the primary map for viewing xm weather data is the weather data link (xm) page in the map page group. This is the only map display capable of showing information for all avai...

  • Page 296

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 284 hazard avoidance weather product symbol expiration time (minutes) refresh rate (minutes) next-generation radar (nexrad) 30 5 (u.S.) 10 (canada) cloud top (cld top) 60 15 echo top (echo top) 30 7.5 xm lightning (ltng) 30 5 cell ...

  • Page 297

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 285 hazard avoidance table 6-2 shows which xm products can be displayed (indicated with a ‘+’ symbol) on specific maps. Weather product pfd inset map navigation map p age w eather data link (xm) p age w eather information page aux ...

  • Page 298

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 286 hazard avoidance softkeys control the display of weather information on most mfd pages and the pfd inset map (figure 6-3 shows the weather product softkeys for the weather data link (xm) page). When a weather product is selecte...

  • Page 299

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 287 hazard avoidance setting up and customizing the weather data link (xm) page: 1) select the weather data link (xm) page. 2) press the menu key. 3) with ‘weather setup’ highlighted, press the ent key (figure 6-4). 4) turn the sma...

  • Page 300

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 288 hazard avoidance maps besides the weather data link (xm) page use settings based on those selected for the navigation map page. Setting up and customizing weather data for the navigation map page: 1) select the navigation map p...

  • Page 301

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 289 hazard avoidance viewing legends for displayed weather products: 1) select the weather data link (xm) page. 2) select the legend softkey to display the legends for the displayed weather products. Or : a) press the menu key. B) ...

  • Page 302

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 290 hazard avoidance nexrad note: nexrad data cannot be displayed at the same time as turbulence, icing, or terrain. Wsr-88d, or nexrad (next-generation radar), is a network of 158 high-resolution doppler radar systems that are ope...

  • Page 303

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 291 hazard avoidance displaying nexrad weather information: 1) select the map softkey (for the pfd inset map, select the inset softkey). This step is not necessary on the weather data link (xm) page. 2) select the nexrad softkey. C...

  • Page 304

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 292 hazard avoidance nexrad l imitations nexrad radar images may have certain limitations: •nexradbasereflectivitydoesnotprovidesufficientinformationtodeterminecloudlayersorprecipitation characteristics (wet hail vs. Rain). For exa...

  • Page 305

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 293 hazard avoidance nexrad l imitations (c anada ) •radarcoverageextendsto55ºn. •anyprecipitationdisplayedbetween52ºnand55ºnisdisplayedasmixedbecauseitisunknown. Figure 6-13 nexrad data - canada no coverage above 55 º n precipitat...

  • Page 306

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 294 hazard avoidance echo tops note: display of echo tops cannot be displayed at the same time as cloud tops and nexrad. Echo tops data (figure 6-14) shows the location, elevation, and direction of the highest radar echo. The highe...

  • Page 307

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 295 hazard avoidance the display of radar coverage is always active when either nexrad or echo tops is selected. Areas where nexrad radar coverage and echo tops information is not currently available or is not being collected are i...

  • Page 308

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 296 hazard avoidance xm lightning lightning data (figure 6-18) shows the approximate location of cloud-to-ground lightning strikes. A strike icon represents a strike that has occurred within a two-kilometer region. The exact locati...

  • Page 309

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 297 hazard avoidance cell movement cell movement data (figure 6-20) shows the location and movement of storm cells as identified by the ground-based system. Cells are represented by yellow squares, with direction of movement indica...

  • Page 310

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 298 hazard avoidance sigmets and airmets sigmet (significant meteorological information) and airmet (airmen’s meteorological information) are issued for potentially hazardous weather. A convective sigmet is issued for hazardous con...

  • Page 311

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 299 hazard avoidance metars and tafs note: atmospheric pressure as reported for metars is given in hectopascals (hpa), except for in the united states, where it is reported in inches of mercury (in hg). Temperatures are reported in...

  • Page 312

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 300 hazard avoidance 4) turn the fms knob or the ent key to scroll through the metar and taf text. Metar text must be completely scrolled through before scrolling through the taf text. 5) press the fms knob or the clr key to return...

  • Page 313

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 301 hazard avoidance surface analysis and city forecast note: surface analysis and city forecast data are displayed only within the installed aviation database service area. Surface analysis and city forecast information is availab...

  • Page 314

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 302 hazard avoidance freezing levels freezing level data shows the color-coded contour lines for the altitude and location at which the first isotherm is found (figure 6-30). When no data is displayed for a given altitude, the data...

  • Page 315

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 303 hazard avoidance winds aloft winds aloft data (figure 6-32) shows the forecasted wind speed and direction at the surface and at selected altitudes. Altitude can be displayed in 3,000-foot increments up to 42,000 feet msl. Displ...

  • Page 316

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 304 hazard avoidance county warnings county data (figure 6-34) provides specific public awareness and protection weather warnings from the national weather service (nws). This can include information on fires, tornadoes, severe thu...

  • Page 317

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 305 hazard avoidance cyclone the cyclone weather product (figure 6-36) shows the current location of cyclones (hurricanes), tropical storms, and their projected tracks. Figure 6-36 cyclone data selected for display cyclone displayi...

  • Page 318

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 306 hazard avoidance icing (cip & sld) note: icing data cannot be displayed at the same time as nexrad data. Current icing product (cip) data shows a graphical view of the current icing environment (figure 6-38). Icing severity is ...

  • Page 319

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 307 hazard avoidance turbulence note: turbulence data cannot be displayed at the same time as nexrad data. Turbulence data (figure 6-40) identifies the potential for erratic movement of high-altitude air mass associated winds. Turb...

  • Page 320

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 308 hazard avoidance pireps and aireps pilot weather reports (pireps) describe in-flight weather encountered by pilots. When significant weather conditions are reported or forecast, air traffic control (atc) facilities are required...

  • Page 321

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 309 hazard avoidance figure 6-43 pirep text on the weather data link (xm) page decoded pirep text raw pirep text selected pirep age of report in hh:mm to display the pirep or airep legend (figure 6-44), press the legend softkey whe...

  • Page 322: 6.2  Worldwide Weather

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 310 hazard avoidance 6.2 worldwide weather note: garmin flight data services worldwide weather provides information for avoiding hazardous weather. Do not utilize worldwide weather information to penetrate hazardous weather. Note: ...

  • Page 323

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 311 hazard avoidance when a weather product is selected for display on the weather data link (gfds) page, a box containing a symbol for the product and its age (in minutes) are shown in the upper right (figure 6-45). If weather dat...

  • Page 324

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 312 hazard avoidance table 6-4 shows which gfds weather products can be displayed (indicated with a ‘+’ symbol) on specific g1000h maps. Gfds weather product pfd inset map navigation map p age w eather data link (gfds) p age w eath...

  • Page 325

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 313 hazard avoidance figure 6-46 gfds weather product softkeys (mfd) press the back softkey to move up one level. Back precip more wx dl ltng ir sat sig/air metar legend chklist 9000 12000 6000 back legend 3000 15000 sfc prev off n...

  • Page 326

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 314 hazard avoidance figure 6-48 weather data link (gfds) page setup menu figure 6-47 weather data link (gfds) page menu restoring default weather data link (gfds) page settings: 1) select the weather data link (gfds) page. 2) pres...

  • Page 327

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 315 hazard avoidance if both gfds and xm weather services are installed, customizing the display settings for the corresponding weather products shown in table 6-5 will result in identical settings for both services. Xm weather pro...

  • Page 328

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 316 hazard avoidance figure 6-50 navigation map page setup menu figure 6-49 navigation map page menu figure 6-51 navigation map page setup menu, weather group each active weather product has an associated legend which can be displa...

  • Page 329: Gfds Weather Data Requests

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 317 hazard avoidance figure 6-52 panning on the gfds data link page additional in- formation on tfr selected with map pointer tfr selected with map pointer gfds weather data requests the gfds data request window provides the flight...

  • Page 330

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 318 hazard avoidance • destination – requests data based on the active flight plan destination (direct-to destinations excluded). See the flight management section for more information about entering and activating flight plans. • ...

  • Page 331

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 319 hazard avoidance figure 6-55 gfds weather data request results with precipitation and infrared satellite displayed present position selected, 200 nm diameter requested destination selected, 200 nm diameter requested next 80 nm ...

  • Page 332

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 320 hazard avoidance at the completion of a successful weather data request, the request status window (if still open) will indicate ‘ok’. Cancelling a gfds weather data request in progress: 1) select the weather data link (gfds) p...

  • Page 333: Worldwide Weather Products

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 321 hazard avoidance worldwide weather products precipitation precipitation (precip) data is not real-time. The lapsed time between collection, processing, and dissemination of radar images can be significant and may not reflect th...

  • Page 334

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 322 hazard avoidance no radar coverage figure 6-57 precipitation data legend boundary of gfds weather data request the display of radar coverage is enabled when precipitation is selected for display. Areas where precipitation radar...

  • Page 335

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 323 hazard avoidance figure 6-58 precipitation data - zoomed block represents 4 km 2 the following may cause abnormalities in displayed radar images: •groundclutter •strobesandspuriousradardata •sunstrobes(whentheradarantennapoints...

  • Page 336

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 324 hazard avoidance infrared satellite infrared satellite (ir sat) data (figure 6-59) depicts cloud top temperatures from satellite imagery. Brighter cloud top colors indicate cooler temperatures occurring at higher altitudes. Fig...

  • Page 337

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 325 hazard avoidance datalink lightning datalink lightning (dl ltng) data (figure 6-61) shows the approximate location of cloud-to-ground lightning strikes. A strike icon represents a strike that has occurred within a two-kilometer...

  • Page 338

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 326 hazard avoidance sigmets and airmets sigmets (significant meteorological information) and airmets (airmen’s meteorological information) are issued for potentially hazardous weather. A convective sigmet is issued for hazardous c...

  • Page 339

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 327 hazard avoidance metars and tafs note: metar information is only displayed within the installed aviation database service area. Metars (meteorological aerodrome reports) typically contain information about the temperature, dewp...

  • Page 340

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 328 hazard avoidance or : 1) select the weather information page. A) turn the large fms knob to select the waypoint page group. B) select the wx softkey to select the weather information page. 2) press the fms knob to display the c...

  • Page 341

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 329 hazard avoidance winds aloft winds aloft data (figure 6-69) shows the forecasted wind speed and direction at the surface and at selected altitudes. Altitude can be displayed in 3,000-foot increments up to 42,000 feet msl. Displ...

  • Page 342

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 330 hazard avoidance pireps pilot weather reports (pireps) describe in-flight weather encountered by pilots. A pirep may contain unforecast adverse weather conditions, such as low in-flight visibility, icing conditions, wind shear,...

  • Page 343

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 331 hazard avoidance figure 6-72 pirep text on the weather data link (gfds) page decoded pirep text raw pirep text to display the pirep or airep legend (figure 6-73), select the legend softkey when pireps or aireps are selected for...

  • Page 344: Abnormal Operations

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 332 hazard avoidance abnormal operations if the g1000h cannot complete a gfds weather data request, one or more messages will appear in the request status window. Weather request status message desciption auto requests inhibited se...

  • Page 345

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 333 hazard avoidance the g1000h also displays message advisories on the pfd which may indicate a problem with the gdl 59h; refer to appendix a for more information. Worldwide weather in reversionary mode when the g1000h is operatin...

  • Page 346: 6.3 Htaws

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 334 hazard avoidance 6.3 htaws warning: do not use htaws information for primary terrain avoidance. Htaws is intended only to enhance situational awareness. Note: the data contained in the htaws databases comes from government agen...

  • Page 347: Displaying Htaws Data

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 335 hazard avoidance pressure, temperature, and lapse rates have fixed values), it is common for the baro-corrected altitude (as read from the altimeter) to differ from the gsl altitude. This variation results in the aircraft’s gsl...

  • Page 348: Htaws Page

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 336 hazard avoidance htaws page the htaws page is specialized to show terrain, obstacle, and potential impact point data in relation to the aircraft’s current altitude, without clutter from the basemap. Aviation data (airports/heli...

  • Page 349

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 337 hazard avoidance figure 6-75 htaws page (360 view) terrain legend map range rings obstacles annunciation window current aircraft gps- derived gsl altitude map orientation figure 6-76 htaws page (arc view) terrain legend map ran...

  • Page 350: Htaws Alerts

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 338 hazard avoidance htaws alerts alerts are issued when flight conditions meet parameters that are set within htaws software algorithms. Htaws alerts typically employ a caution or a warning alert severity level, or both. When an a...

  • Page 351

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 339 hazard avoidance alert type pfd/htaws page alert annunciation mfd pop-up alert (except htaws page) aural message reduced required terrain clearance warning (rtc) “warning; terrain, terrain” imminent terrain impact warning (iti)...

  • Page 352

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 340 hazard avoidance imminent terrain impact (iti) and imminent obstacle impact (ioi) alerts are issued when the aircraft is below the elevation of a terrain or obstacle cell in the aircraft’s projected path. Iti and ioi alerts are...

  • Page 353

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 341 hazard avoidance enabling/disabling rp mode: 1) turn the large fms knob to select the htaws page. 2) press the rp mode softkey to inhibit or enable rp mode (choice dependent on current state). Or : 1) press the menu key. 2) tur...

  • Page 354

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 342 hazard avoidance altitude voice callout (vco) aural alerts htaws provides aural altitude advisory alerts as the aircraft descends. Vco alerts are based on either radar altitude (if a radar altimeter is installed and available) ...

  • Page 355: System Status

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 343 hazard avoidance system status during system power-up, htaws conducts a system-test of its aural and visual annunciations. The system test can also be manually initiated. An aural alert is issued at test completion. Htaws syste...

  • Page 356

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 344 hazard avoidance ‘htaws n/a’ is generated in the annunciation window and on the htaws page. The aural message “htaws not available” is also generated. When sufficient gps signal is received and the aircraft is within the databa...

  • Page 357

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 345 hazard avoidance 6.4 traffic information service (tis) warning: the traffic information service (tis) is intended for advisory use only. Tis is intended to help the pilot locate traffic visually. It is the responsibility of the...

  • Page 358: Displaying Traffic Data

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 346 hazard avoidance the altitude difference between the requesting aircraft and other intruder aircraft is displayed above/below the traffic symbol in hundreds of feet. If the other aircraft is above the requesting aircraft, the a...

  • Page 359

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 347 hazard avoidance displaying traffic information (pfd inset map): 1) select the inset softkey. 2) select the traffic softkey to display traffic data on the inset map (trfc-1). 3) select the softkey again to display the traffic-o...

  • Page 360: Traffic Map Page

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 348 hazard avoidance figure 6-86 navigation map page setup menu figure 6-85 navigation map page menu figure 6-87 navigation map page setup menu, traffic group the navigation map page setup menu provides a means in addition to the s...

  • Page 361: Tis Alerts

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 349 hazard avoidance or : a) press the menu key. B) select ‘operate mode’ (shown if tis is in standby mode) and press the ent key. Display of system status figure 6-88 traffic map page traffic advisory, 300’ above, descending non-t...

  • Page 362

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 350 hazard avoidance figure 6-89 traffic annunciation (pfd) inset map displays when ta is detected a “tis not available” (tna) voice alert is generated when the tis service becomes unavailable or is out of range. Tis may be unavail...

  • Page 363: System Status

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 351 hazard avoidance system status the g1000h performs an automatic test of tis during power-up. If tis passes the test, tis enters standby mode (on the ground) or operating mode (in the air). If tis fails the power up test, an ann...

  • Page 364

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 352 hazard avoidance mode traffic mode annunciation (traffic map page) traffic display enabled icon (other maps) tis operating operating tis standby standby (also shown in white in center of page) tis failed* fail * see table 6-15 ...

  • Page 365: 6.5  Garmin Gts Traffic

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 353 hazard avoidance 6.5 garmin gts traffic warning: the gts 800 traffic advisory system (tas) is intended for advisory use only to aid the pilot in visually acquiring traffic. No avoidance maneuvers should be based solely upon tas...

  • Page 366

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 354 hazard avoidance tas symbology the gts 800 uses symbology to depict intruding traffic using the symbols shown in table 6-16. Symbol description traffic advisory (ta) arrow with ads-b directional information. Points in the direc...

  • Page 367

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 355 hazard avoidance a vertical trend arrow to the right of the intruder symbol (figure 6-91) indicates climbing or descending traffic with an upward or downward-pointing arrow respectively. Relative altitude vertical trend arrow f...

  • Page 368

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 356 hazard avoidance ta alerting conditions the traffic system automatically adjusts its ta sensitivity level to reduce the likelihood of nuisance ta alerting during flight phases likely to be near airports. Level a (less) ta sensi...

  • Page 369: Tas Alerts

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 357 hazard avoidance tas alerts when the traffic system detects a new ta, the following occur: •asingle“traffic!” voice alert is generated, followed by additional voice information about the bearing, relative altitude, and approxim...

  • Page 370: System Test

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 358 hazard avoidance system test note: traffic surveillance is not available during the system test. Use caution when performing a system test during flight. The traffic system provides a system test mode to verify the system is op...

  • Page 371: Operation

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 359 hazard avoidance operation after power-up, the traffic system is in standby mode. The system must be in operating mode for traffic to be displayed and for tas to be issued. Selecting the operate softkey allows the system to swi...

  • Page 372

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 360 hazard avoidance figure 6-95 traffic map page altitude mode proximity traffic, 900’ above, level, flight id displayed “no bearing” traffic (bearing undetermined), distance 4.0 nm, 500’ above, climbing non-threat traffic, 2500’ ...

  • Page 373

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 361 hazard avoidance a ltitude d isplay the pilot can select the volume of airspace in which non-threat and proximity traffic is displayed. Tas occurring outside of these limits will always be shown. Changing the altitude range: 1)...

  • Page 374

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 362 hazard avoidance f light id d isplay the flight ids of other aircraft (when available) can be enabled for display on the traffic map page (figure 6-96). When a flight id is received, it will appear above or below the correspond...

  • Page 375

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 363 hazard avoidance figure 6-97 traffic map page menu t raffic m ap p age d isplay r ange the display range on the traffic map page can be changed at any time. Map range is adjustable with the range knob from 2 to 12 nm, as indica...

  • Page 376

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 364 hazard avoidance displaying traffic on the navigation map 1) ensure the tas system is operating. With the navigation map displayed, select the map softkey. 2) select the traffic softkey. Traffic is now displayed on the map as s...

  • Page 377

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 365 hazard avoidance customizing the traffic display on the navigation map page: 1) select the navigation map page. 2) press the menu key. 3) with map setup highlighted, press the ent key (figure 6-99). 4) turn the small fms knob t...

  • Page 378

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 366 hazard avoidance the navigation map page setup menu also controls the display of traffic. The setup menu controls the map range settings. Traffic data symbols and labels can be decluttered from the display. If a map range large...

  • Page 379

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 367 hazard avoidance the annunciations to indicate the status of traffic information appear in a banner at the lower left corner of maps on which traffic can be displayed. Traffic status banner annunciation description ta off scale...

  • Page 380

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 368 hazard avoidance b lank p age.

  • Page 381

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 369 automatic flight control system section 7 automatic flight control system not available..

  • Page 382

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 370 automatic flight control system b lank p age.

  • Page 383

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 371 additional features section 8 additional features note: with the availability of safetaxi, chartview, or flitecharts in electronic form, it is still advisable to carry another source of charts on board the aircraft. Additional ...

  • Page 384

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 372 additional features 8.1 synthetic vision system (svs) warning: use appropriate primary systems for navigation, and for terrain, obstacle, and traffic avoidance. Svs is intended as an aid to situational awareness only and may no...

  • Page 385: Svs Operation

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 373 additional features figure 8-1 synthetic vision imagery svs operation svs is activated from the pfd using the softkeys located along the bottom edge of the display. Pressing the softkeys turns the related function on or off. Wh...

  • Page 386

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 374 additional features figure 8-2 svs softkeys pressing the back softkey returns to the top-level softkeys. Back back pfd pressing the back softkey returns to the previous level of softkeys. Syn vis pathway syn terr hrzn hdg aptsi...

  • Page 387: Svs Features

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 375 additional features svs features figure 8-3 svs on the primary flight display svs softkeys synthetic terrain pathways flight path marker airport runway zero pitch line (zpl) with compass heading marks airplane symbol selected a...

  • Page 388

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 376 additional features figure 8-4 programmed and selected altitude selected altitude programmed altitudes pathways provide supplemental glidepath/glideslope information on an active ils, lpv, lnav/vnav, and some lnav approaches. P...

  • Page 389

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 377 additional features d escent and a pproach pathways are shown descending only for a programmed descent (figures 8-5, 8-6). When the flight plan includes programmed descent segments, pathways are displayed along the descent path...

  • Page 390

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 378 additional features m issed a pproach upon activating the missed approach, pathways lead to the missed approach holding point (mahp) and are displayed as a level path at the published altitude for the mahp, or the selected alti...

  • Page 391

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 379 additional features flight path marker note: the flight path marker is not available when the cross-pointer (x-pointer) flight director format is selected. The flight path marker (fpm), also known as a velocity vector, is displ...

  • Page 392

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 380 additional features horizon heading the horizon heading is synchronized with the hsi and shows approximately 60 degrees of compass heading in 30-degree increments on the zero pitch line. Horizon heading tick marks and digits ap...

  • Page 393

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 381 additional features runways warning: do not use svs runway depiction as the sole means for determining the proximity of the aircraft to the runway or for maintaining the proper approach path angle during landing. Note: not all ...

  • Page 394

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 382 additional features htaws alerting terrain alerting on the synthetic terrain display is triggered by forward-looking terrain avoidance (flta). When an obstacle becomes a potential impact point the color of the obstacle matches ...

  • Page 395

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 383 additional features obstacles are represented on the synthetic terrain display by standard two-dimensional tower symbols as found on mfd htaws page and charts. Obstacle symbols appear in the perspective view with relative heigh...

  • Page 396: Field Of View

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 384 additional features field of view the pfd field of view can be represented on the mfd navigation map page. Two dashed lines forming a v-shape in front of the aircraft symbol on the map, represent the forward viewing area shown ...

  • Page 397

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 385 additional features the following figure compares the pfd forward looking depiction with the mfd plan view and field of view turned on. Figure 8-13 pfd and mfd field of view comparison lines depict pfd field of view svs view on...

  • Page 398: 8.2 Safetaxi

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 386 additional features 8.2 safetaxi safetaxi is an optional feature that gives greater map detail when viewing airports at close range. The maximum map ranges for enhanced detail are pilot configurable. When viewing at ranges clos...

  • Page 399

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 387 additional features figure 8-14 safetaxi depiction on the navigation map page dcltr softkey removes taxiway markings airport features aircraft position taxiway identification airport hot spot outline the dcltr softkey (declutte...

  • Page 400

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 388 additional features configuring safetaxi range: 1) while viewing the navigation map page, press the menu key to display the page menu. 2) turn the large fms knob to highlight the map setup menu option and press the ent key. Fig...

  • Page 401

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 389 additional features safetaxi database is revised every 56 days. Safetaxi is always available for use after the expiration date. When turning on the system, the power-up page indicates whether the databases are current, out of d...

  • Page 402

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 390 additional features the safetaxi database cycle number shown in the figure, 10s5, is deciphered as follows: 10 – indicates the year 2010 s – indicates the data is for safetaxi 5 – indicates the fifth issue of the safetaxi datab...

  • Page 403

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 391 additional features figure 8-19 illustrates possible safetaxi database conditions that may appear on the aux - system status page. The effective date is the beginning date for this database cycle. If the present date is before ...

  • Page 404: 8.3 Chartview

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 392 additional features 8.3 chartview chartview is an optional feature resembling the paper version of jeppesen terminal procedures charts. The charts are displayed in full color with high-resolution. The mfd depiction shows the ai...

  • Page 405: Terminal Procedures Charts

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 393 additional features terminal procedures charts selecting terminal procedures charts: while viewing the navigation map page, nearest airport page, or flight plan page, select the shw chrt softkey. Or : 1) press the menu key to d...

  • Page 406

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 394 additional features when a chart is not available by selecting the shw chrt softkey or selecting a page menu option, charts may be obtained for other airports from the wpt pages or flight plan pages. If a chart is available for...

  • Page 407

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 395 additional features while the approach box is selected using the fms knob, the g1000h softkeys are blank. Once the desired chart is selected, the chart scale can be changed and the chart page can be scrolled using the joystick....

  • Page 408

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 396 additional features selecting the info-1 or info-2 softkey returns to the airport diagram chart when the view is on a terminal procedure chart. If the displayed chart is the airport diagram chart, selecting the info-1 or info-2...

  • Page 409

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 397 additional features in the example shown in figure 8-26, the class b chart is selected. Pressing the ent key displays the charlotte class b airspace chart (figure 8-27). Figure 8-27 airport information page, class b chart selec...

  • Page 410

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 398 additional features selecting the star softkey displays the standard terminal arrival chart if available. Change range and scroll through the chart with the joystick figure 8-29 arrival information page chart not to scale aircr...

  • Page 411

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 399 additional features selecting the wx softkey shows the airport weather frequency information, and includes weather data such as metar and taf from the xm data link receiver, when available. Weather information is available only...

  • Page 412

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 400 additional features figure 8-32 notam softkey highlighted notam softkey appears for selected airports figure 8-33 airport information page, local notams local notam on this airport notam softkey selected selecting the notam sof...

  • Page 413: Chart Options

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 401 additional features chart options selecting the chrt opt softkey displays the next level of softkeys, the chart options level (figure 8-20). Selecting the all softkey shows the complete approach chart on the screen. Figure 8-34...

  • Page 414

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 402 additional features selecting the header softkey shows the header view (approach chart briefing strip) on the screen. Approach chart briefing strip figure 8-35 approach information page, header view selecting the plan softkey s...

  • Page 415

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 403 additional features selecting the profile softkey displays the approach chart descent profile strip. Approach chart descent profile strip figure 8-37 approach information page, profile view, full screen width selecting the mini...

  • Page 416

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 404 additional features if the chart scale has been adjusted to view a small area of the chart, selecting the fit width softkey changes the chart size to fit the available screen width. Select fit wdth softkey to show full chart wi...

  • Page 417

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 405 additional features selecting the full scn softkey alternates between removing and replacing the data window to the right. Selecting additional information: 1) while viewing the airport taxi diagram, select the full scn softkey...

  • Page 418

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 406 additional features the full screen view can also be selected by using the page menu option. Selecting full screen on or off: 1) while viewing a terminal chart press the menu key to display the page menu options. 2) turn the la...

  • Page 419: Day/night View

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 407 additional features day/night view chartview can be displayed on a white or black background for day or night viewing. The day view offers a better presentation in a bright environment. The night view gives a better presentatio...

  • Page 420

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 408 additional features figure 8-43 arrival information page, day view figure 8-44 arrival information page, night view.

  • Page 421

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 409 additional features chartview cycle number and expiration date chartview database is revised every 14 days. Charts are still viewable during a period that extends from the cycle expiration date to the disables date. Chartview i...

  • Page 422

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 410 additional features the chartview time critical information can also be found on the aux - system status page. The database cycle number, expires, and disables dates of the chartview subscription appear in either blue or yellow...

  • Page 423

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 411 additional features other possible aux - system status page conditions are shown in figure 8-47. The expires date is the revision date for the next database cycle. The disables date is the date that this database cycle is no lo...

  • Page 424: 8.4 Flitecharts

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 412 additional features 8.4 flitecharts flitecharts is an optional feature resembling the paper version of aeronav services terminal procedures charts. The charts are displayed with high-resolution and in color for applicable chart...

  • Page 425: Terminal Procedures Charts

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 413 additional features terminal procedures charts selecting terminal procedures charts: while viewing the navigation map page, nearest airport page, or flight plan page, select the shw chrt softkey. Or : 1) press the menu key to d...

  • Page 426

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 414 additional features when a chart is not available by selecting the shw chrt softkey or selecting a page menu option, charts may be obtained for other airports from the wpt pages or flight plan pages. If a chart is available for...

  • Page 427

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 415 additional features while the approach box is selected using the fms knob, the g1000h softkeys are blank. Once the desired chart is selected, the chart scale can be changed and the chart can be panned using the joystick. Pressi...

  • Page 428

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 416 additional features selecting the info-1 or info-2 softkey returns to the airport diagram chart when the view is on a terminal procedure chart. If the displayed chart is the airport diagram chart, selecting the info-1 or info-2...

  • Page 429

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 417 additional features in the example shown in figure 8-54, take off minimums is selected. Pressing the ent key displays the take-off minimums and departure procedures chart (figure 8-55). Figure 8-55 airport information page, tak...

  • Page 430

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 418 additional features selecting the star softkey displays the standard terminal arrival chart if available. Figure 8-57 arrival information page selecting the apr softkey displays the approach chart for the airport if available. ...

  • Page 431

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 419 additional features selecting the wx softkey shows the airport weather frequency information, when available, and includes weather data such as metar and taf from the xm data link receiver. Weather information is available only...

  • Page 432: Chart Options

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 420 additional features chart options selecting the chrt opt softkey displays the next level of softkeys, the chart options level (figure 8-48). Selecting the all softkey shows the complete chart on the screen. Complete chart shown...

  • Page 433

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 421 additional features selecting the fit width softkey fits the width of the chart in the display viewing area. In the example shown, the chart at close range is replaced with the full width chart. Figure 8-61 approach information...

  • Page 434

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 422 additional features selecting the full scn softkey alternates between removing and replacing the data window to the right. Select full scn softkey to switch between chart on full screen and chart with info window figure 8-62 ai...

  • Page 435

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 423 additional features the full screen view can also be selected by using the page menu option. Selecting full screen on or off: 1) while viewing a terminal chart press the menu key to display the page menu options. 2) turn the la...

  • Page 436: Day/night View

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 424 additional features day/night view flitecharts can be displayed on a white or black background for day or night viewing. The day view offers a better presentation in a bright environment. The night view gives a better presentat...

  • Page 437

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 425 additional features figure 8-65 approach information page, day view figure 8-66 approach information page, night view.

  • Page 438

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 426 additional features flitecharts cycle number and expiration date flitecharts data is revised every 28 days. Charts are still viewable during a period that extends from the cycle expiration date to the disables date. Flitecharts...

  • Page 439

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 427 additional features when the 180 day grace period has expired, ‘chart data is disabled.’ in yellow indicates that the flitecharts database has expired and is no longer viewable. ‘chart data: n/a’ appears in white if no flitecha...

  • Page 440

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 428 additional features the flitecharts database is provided from garmin. Refer to updating garmin databases in appendix b for instructions on revising the flitecharts database. The other three possible aux - system status page con...

  • Page 441: 8.5 Aopa Airport Directory

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 429 additional features 8.5 aopa airport directory the aircraft owners and pilots association (aopa) airport directory database offers detailed information regarding services, hours of operation, lodging options, and more. This inf...

  • Page 442

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 430 additional features aopa database cycle number and revision the aopa airport directory database is revised four times per year. Check fly.Garmin.Com for the current database. The airport directory is always available for use af...

  • Page 443

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 431 additional features the airport directory region, version, cycle, effective date and expires date of the database cycle can also be found on the aux - system status page, as seen in figure 8-72. Select the mfd1 db softkey to pl...

  • Page 444

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 432 additional features 8.6 satellite telephone and data link services note: separate accounts must be established to access the iridium satellite network for voice and garmin flight data services for data transmission of maintenan...

  • Page 445

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 433 additional features figure 8-73 report status page selected prior to system registration 5) press the menu key. The page menu window is now displayed as seen in figure 8-74. 6) select ‘register with gfds’ in the menu list. Figu...

  • Page 446

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 434 additional features 7) press the ent key. The garmin flight data service registration window is now displayed as shown in figure 8-75. Figure 8-75 enter access code 8) enter the access code provided by garmin flight data servic...

  • Page 447

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 435 additional features disable/enable iridium transceiver iridium telephone and data communications may be turned on or off by performing these simple steps. Disabling/enabling telephone and low speed data services: 1) turn the la...

  • Page 448: Telephone Communication

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 436 additional features telephone communication the pilot or copilot can place and answer calls on the iridium satellite network. Control and monitoring of telephone functions are accomplished through the aux-telephone page. To vie...

  • Page 449

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 437 additional features internal phone external phone description phone is idle phone is ringing phone has a dial tone (off hook) or connected to another phone phone dialed is busy phone is dialing another phone phone has failed ph...

  • Page 450

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 438 additional features incoming calls note: outside callers should dial 00 + 8816 or 8817 + aircraft phone number when calling the aircraft iridium telephone system. When viewing mfd pages other than the aux-telephone page, a pop-...

  • Page 451

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 439 additional features disabling incoming call alerts: 1) with the aux-telephone page displayed, press the menu key on the mfd to display the page menu. 2) turn either fms knob to place the cursor on ‘disable incoming call alerts’...

  • Page 452

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 440 additional features 4) press the ent key. ‘ok’ is highlighted as in figure 8-82. Figure 8-82 make the call 5) press the ent key. The system will begin calling the number, as in figure 8-83. Figure 8-83 system is making the conn...

  • Page 453

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 441 additional features when the phone is answered, the connection is established as shown in figure 8-84. To exit the call, select the hangup softkey. Figure 8-84 phone is answered, connection complete.

  • Page 454

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 442 additional features placing the call on hold to place a call on hold: select the hold softkey on the mfd. Or : 1) press the menu key to display the page menu. 2) turn either fms knob to place the cursor on ‘put current call on ...

  • Page 455: Text Messaging (Sms)

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 443 additional features text messaging (sms) the pilot or copilot can send and receive text messages on the iridium satellite network. Messages may be sent to an email address or text message capable cellular telephone. Message len...

  • Page 456

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 444 additional features message symbol description received text message that has not been opened received text message that has been opened saved text message, draft not sent system is sending text message text message has been se...

  • Page 457

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 445 additional features figure 8-88 text message displayed from pop-up alert the pop-up alerts may be enabled or disabled through the page menu. Enabling/disabling incoming text message pop-up alerts: 1) with the aux-text messaging...

  • Page 458

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 446 additional features reply to a text message after reading a text message, a reply may be sent. Replying to a text message: while viewing the text message, select the reply softkey. Or : 1) press the menu key to display the page...

  • Page 459

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 447 additional features 2) the text message draft window is now displayed with the cursor in the ‘to’ field. Enter 00 + country code + area code + phone number when sending to a text capable telephone. An email address may also be ...

  • Page 460

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 448 additional features or : a) press the menu key to display the page menu. B) turn either fms knob to place the cursor on ‘draft new predefined message’. C) press the ent key. The predefined sms text message window is now display...

  • Page 461

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 449 additional features sending a predefined text message: 1) while viewing the aux-text messaging page, select the new softkey. 2) the text message draft window is now displayed with the cursor in the ‘to’ field. Enter the desired...

  • Page 462

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 450 additional features 4) select the predefd softkey. The predefined message menu window is displayed as seen in figure 8-94. Figure 8-94 predefined message list 5) turn either fms knob to select the desired predefined message. 6)...

  • Page 463

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 451 additional features figure 8-95 text message inbox show outbox messages: while viewing the aux-text messaging page, select the arrange softkey, then select the outbox softkey. Or : 1) press the menu key to display the page menu...

  • Page 464

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 452 additional features managing text messages the viewed messages may be listed according to the date/time the message was sent or received, the type of message (read, unread, sent, unsent, etc.), or by message address. Viewing me...

  • Page 465

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 453 additional features a) press the menu key to display the page menu. B) turn either fms knob to place the cursor on ‘view selected message’. C) press the ent key. Message content is displayed as shown in figure 8-96. Figure 8-96...

  • Page 466: Wi-Fi Connections

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 454 additional features marking all messages as read: 1) while viewing the inbox on the aux-text messaging page, press the menu key to display the page menu. 2) turn either fms knob to place the cursor on ‘mark all new messages as ...

  • Page 467

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 455 additional features to set up a new wi-fi connection: 1) select the avail softkey on the mfd. A list of available networks will be displayed in the available networks window as shown in figure 8-97. Signal strength is shown for...

  • Page 468

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 456 additional features 4) turn either fms knob to select the desired network. See figure 8-98. Figure 8-98 desired network selected 5) select the connect softkey. Or : a) press the menu key to display the page menu. B) turn either...

  • Page 469

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 457 additional features 7) press the ent key. ‘ok’ will be highlighted. 8) press the ent key again. 9) the save settings window is now displayed with the cursor highlighting ‘save connection’. Figure 8-100 save option 10) the selec...

  • Page 470

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 458 additional features to edit a saved network: 1) while viewing list of saved networks, press the fms knob to activate the cursor as seen in figure 8-102. 2) turn either fms knob to highlight the network to be edited. 3) pressing...

  • Page 471

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 459 additional features 4) select the edit softkey. The cursor now appears in the connection settings window as shown in figure 8-103. Figure 8-103 select attributes to edit 5) turn the large fms knob to select the network attribut...

  • Page 472: System Data Logging

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 460 additional features system data logging note: an account must be established with garmin flight data services to make full use of the system data logging feature. The system provides recording of cas and cmc messages that occur...

  • Page 473

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 461 additional features to change transmission method: 1) while viewing the report status page, press the fms knob to activate the cursor. 2) turn the large fms knob to move the cursor to the 1st or 2nd transmit method for the desi...

  • Page 474

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 462 additional features to send a transmission manually: note: manual transmission of data can only be performed while the aircraft is on the ground. 1) while viewing the report status page, press the fms knob to activate the curso...

  • Page 475

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 463 additional features 8.7 xm radio entertainment note: refer to the hazard avoidance section for information about xm weather products. The optional xm radio entertainment feature of the gdl 69a data link receiver is available fo...

  • Page 476: Using Xm Radio

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 464 additional features 6) select the lock softkey. 7) turn the large fms knob to highlight yes. 8) to complete activation, press the ent key. Radio and info softkeys figure 8-108 xm information page audio radio id weather products...

  • Page 477

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 465 additional features figure 8-109 xm radio page volume field categories field channel list active channel active channel and channel list the active channel box on the xm radio page displays the currently selected channel that t...

  • Page 478

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 466 additional features category the category box of the xm radio page displays the currently selected category of audio. Categories of channels such as jazz, rock, or news can be selected to list the available channels for a type ...

  • Page 479

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 467 additional features presets up to 15 channels from any category can be assigned a preset number. The preset channels are selected by selecting the presets and more softkeys. Then the preset channel can be selected directly and ...

  • Page 480: 8.8 Scheduler

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 468 additional features 8.8 scheduler the scheduler feature can be used to enter and display reminder messages (e.G., phase 1 inspection, switch fuel tanks, or altimeter-transponder check) in the alerts window on the pfd. Messages ...

  • Page 481

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 469 additional features 9) for event-based messages: a) use the fms knob to enter the desired date (dd-mm-yy) and press the ent key. B) press the ent key again or use the large fms knob to move the cursor to the next field. C) use ...

  • Page 482: 8.9  Auxiliary Video

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 470 additional features 8.9 auxiliary video the g1000h system provides an optional control and display interface to an auxiliary video system. The system can display video for up to two inputs. There are four modes of operation of ...

  • Page 483: Video Setup

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 471 additional features selecting video menu options: 1) while viewing the aux - video page press the menu key to display the page menu options. 2) turn the large fms knob to highlight the desired video adjustment option and press ...

  • Page 484: Display Selection

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 472 additional features display selection pressing the hide map softkey removes the map and displays video on the full screen. The softkey label changes to grey with black characters. Pressing the hide map softkey again restores th...

  • Page 485: Input Selection

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 473 additional features input selection while on the aux - video page, press the input softkey to select input 1 or input 2. The selected input is displayed in the upper left of the video display. Zoom/range pressing the vid zm + o...

  • Page 486: 8.9  Abnormal Operation

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 474 additional features 8.9 abnormal operation svs troubleshooting svs is intended to be used with traditional attitude, heading, obstacle, terrain, and traffic inputs. Svs is disabled when valid attitude or heading data is not ava...

  • Page 487: Unusual Attitudes

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 475 additional features unusual attitudes unusual attitudes are displayed with red chevrons overlaid on the display indicating the direction to fly to correct the unusual attitude condition. The display shows either a brown or blue...

  • Page 488

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 476 additional features gdl 69h/69ah data link receiver troubleshooting some quick troubleshooting steps listed below can be performed to find the possible cause of a failure. •ensuretheowner/operatoroftheaircraftinwhichthedatalink...

  • Page 489

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 477 additional features if a failure still exists, the following messages may provide insight as to the possible problem: message message location description check antenna xm radio page - active channel field data link receiver an...

  • Page 490

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A 478 additional features b lank p age.

  • Page 491: Annunciations and Alerts

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 479 appendix a annunciations and alerts cas messages warning messages see the rotorcraft flight manual (rfm) for recommended pilot actions. Annunciation text description audio alert battery hot battery overheat detected. Single chi...

  • Page 492

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 480 appendix a annunciation text description audio alert mgt miscomp mgt miscompare event. Single ping ng exceed engine ng is in exceedance. Ng miscomp ng miscompare event. Np exceed engine np is in exceedance. Np miscomp np miscom...

  • Page 493: G1000H System Annunciations

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 481 appendix a g1000h system annunciations when a new message is issued, the msg softkey will flash to alert the flight crew of a new message. It will continue to flash until acknowledged by pressing the softkey. Active messages ar...

  • Page 494

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 482 appendix a figure a-2 g1000h system failure annunciations gdc 74b air data computer gtx 33/d transponder or gia 63w integrated avionics units gdc 74b air data computer gea 71 engine airframe unit or gia 63w integrated avionics ...

  • Page 495

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 483 appendix a system annunciation comment display system is not receiving airspeed input from air data computer. Display system is not receiving valid heading input from ahrs. Display system is not receiving altitude input from th...

  • Page 496

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 484 appendix a htaws alerts alert type pfd/htaws page alert annunciation mfd pop-up alert (except htaws page) aural message reduced required terrain clearance warning (rtc) “warning; terrain, terrain” imminent terrain impact warnin...

  • Page 497

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 485 appendix a alert type pfd/htaws page status annunciation htaws page center banner annunciation aural message terrain or obstacle database unavailable or invalid on all displays, invalid software configuration, htaws audio fault...

  • Page 498

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 486 appendix a g1000h system message advisories note: this section provides information regarding g1000h message advisories that may be displayed by the system. Knowledge of the aircraft, systems, flight conditions, and other exist...

  • Page 499

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 487 appendix a database message advisories message comments mfd1 db err – mfd1 navigation database error exists. The mfd and/or pfd detected a failure in the navigation database. Attempt to reload the navigation database. If proble...

  • Page 500

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 488 appendix a database message advisories (cont.) message comments db mismatch – terrain database mismatch. The pfds and mfd have different terrain database versions or types installed. Install correct terrain database version or ...

  • Page 501

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 489 appendix a gia 63h message advisories (cont.) message comments gia1 cooling – gia1 over temperature. The gia1 and/or gia2 temperature is too high. If problem persists, the system should be serviced. Gia2 cooling – gia2 over tem...

  • Page 502

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 490 appendix a gia 63h message advisories (cont.) message comments gps nav lost – loss of gps navigation. Position error. Loss of gps navigation due to position error. Gps nav lost – loss of gps navigation. Gps fail. Loss of gps na...

  • Page 503

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 491 appendix a gtx 33h message advisories message comments xpdr1 config – xpdr1 config error. Config service req’d. The transponder configuration settings do not match those of backup configuration memory. The system should be serv...

  • Page 504

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 492 appendix a gsr 56h message advisories message comments gsr1 fail – gsr1 has failed. A failure has been detected in the #1 gsr 56h. The system should be serviced. Gdl 59h message advisories message comments gdl59 config – gdl 59...

  • Page 505

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 493 appendix a gdc 74h message advisories message comments adc1 alt ec – adc1 altitude error correction is unavailable. Gdc is reporting that the altitude error correction is unavailable. Adc1 as ec – adc1 airspeed error correction...

  • Page 506

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 494 appendix a miscellaneous message advisories (cont.) message comments wpt arrival – arriving at waypoint -[xxxx] arriving at waypoint [xxxx], where [xxxx] is the waypoint name. Steep turn – steep turn ahead. A steep turn is 15 s...

  • Page 507

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 495 appendix a miscellaneous message advisories (cont.) message comments mag var warn – large magnetic variance. Verify all course angles. The gdu’s internal model cannot determine the exact magnetic variance for geographic locatio...

  • Page 508

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 496 appendix a flight plan import/export results description ‘some waypoints not loaded. Waypoints locked.’ the flight plan on the sd card contains one or more waypoints that the system cannot find in the navigation database. The f...

  • Page 509: Database Management

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 497 appendix b database management caution: never disconnect power to the system when loading a database. Power interuption during the database loading process could result in maintenance being required to reboot the system. The sy...

  • Page 510

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 498 appendix b updating the active jeppesen navigation database (not using the dual navigation database or automatic database synchronization features): 1) with the system off, insert the sd card containing the new navigation datab...

  • Page 511

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 499 appendix b dual navigation database feature the dual navigation database feature allows each display to store an upcoming navigation database on the bottom sd card so that the system can automatically load it to replace the act...

  • Page 512

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 500 appendix b 5) after the navigation database files are copied to the bottom sd card, the display will appear as shown in figure b-4. Figure b-4 standby navigation database update complete 6) as instructed on the display, press a...

  • Page 513: Garmin Databases

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 501 appendix b 13) turn system power off. 14) remove the sd card from the top card slot of the mfd. 15) turn system power on. 16) press the ent key to acknowledge the startup screen. 17) turn the large fms knob to select the aux pa...

  • Page 514

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 502 appendix b since these databases are not stored internally in the displays, a supplemental data card containing identical database versions must be kept in each display unit. The basemap database contains data for the topograph...

  • Page 515

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 503 appendix b the synchronization progress may be monitored on the aux-system status page in the sync status section of the database window (figure b-8). This section shows the synchronization status of each applicable database, i...

  • Page 516

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 504 appendix b error message description canceled database synchronization has been canceled by removing the bottom sd card in display being updated card full sd card does not contain sufficient memory err displayed for all other e...

  • Page 517

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 505 appendix b figure b-10 database information on the power-up screen 5) acknowledge the power-up page agreement by pressing the ent key or the right most softkey. 6) turn the large fms knob to select the aux page group on the mfd...

  • Page 518

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 506 appendix b b lank p age.

  • Page 519: Glossary

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 507 appendix c acc accuracy act, actv active, activate adc air data computer adf automatic direction finder adi attitude direction indicator af arc to fix afcs automatic flight control system afrm airframe agl above ground level ah...

  • Page 520

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 508 appendix c dec fuel decrease fuel deg degree deic, deice de-icing dep departure desired track the desired course between the active “from” and “to” waypoints. Dest destination df direct to fix dflt default dgrd degrade dh decis...

  • Page 521

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 509 appendix c ga go-around gal, gl gallon(s) gbox gearbox gdc garmin air data computer gdu garmin display unit gea garmin engine/airframe unit geo geographic gfc garmin flight control gia garmin integrated avionics unit gls global...

  • Page 522

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 510 appendix c leg the portion of a flight plan between two waypoints. Lifr low instrument flight rules lnav lateral navigation lo low loc localizer loi loss of integrity (gps) lon longitude lpv localizer performance with vertical ...

  • Page 523

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 511 appendix c rf constant radius turn to fix rfm rotorcraft flight manual rfms rotorcraft flight manual supplement rmi radio magnetic indicator rmt remote rng range rnwy runway rol roll rom read only memory rpm revolutions per min...

  • Page 524

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 512 appendix c vertical speed required the vertical speed necessary to descend/ climb from a current position and altitude to a defined target position and altitude, based upon current groundspeed. Vfom vertical figure of merit vfr...

  • Page 525: Frequently Asked Questions

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 513 appendix d frequently asked questions if a particular aspect of g1000h operational capability is not addressed by these commonly asked questions or in the index, contact garmin (see the copyright page or back cover for contact ...

  • Page 526

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 514 appendix d for raim to work correctly, the gps receiver must track at least five satellites. A minimum of six satellites is required to allow raim to eliminate a single corrupt satellite from the navigation solution. Raim ensur...

  • Page 527

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 515 appendix d normal (obs not activated) •automatic sequencing of waypoints •manualcoursechangeonhsinotpossible •alwaysnavigates‘to’theactivewaypoint •mustbeinthismodeforfinalapproach course obs •manualsequencing-‘holds’onselected...

  • Page 528

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 516 appendix d w hen does the cdi scale change ? Once a departure is activated, the course deviation indicator (cdi) full scale deflection is set to 0.3 nm. The cdi scale changes to 1.0 nm (terminal mode) then ramps up to 2.0 nm (e...

  • Page 529: General Tis Information

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 517 appendix e general tis information introduction note: aircraft without an operating transponder are invisible to tis. The traffic information service (tis) provides traffic advisory information to non-tas/tcas-equipped aircraft...

  • Page 530

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 518 appendix e warning: garmin is not responsible for mode s geographical coverage. Operation of the ground stations is the responsibility of the faa. Refer to the aim for a terminal mode s radar site map. Note: tis is unavailable ...

  • Page 531: Display Symbols

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 519 appendix f airport item symbol unknown airport non-towered, non-serviced airport towered, non-serviced airport non-towered, serviced airport towered, serviced airport restricted (private) airport heliport navaids item symbol in...

  • Page 532

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 520 appendix f line symbols item symbol icao control area class b airspace mode c tower area warning area alert area caution area danger area prohibited area restricted area training area unknown area class c terminal radar service...

  • Page 533

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 521 appendix f obstacle database unlighted obstacle lighted obstacle obstacle location 1000’ agl 1000’ agl red obstacle is at or above current aircraft altitude yellow obstacle is between 0’ and 250’ below current aircraft altitude...

  • Page 534

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx 522 appendix f miscellaneous item symbol artcc frequency or fss frequency default map pointer elevation pointer wind vector measuring pointer overzoom indicator terrain proximity or taws enabled traffic enabled user waypoint vertic...

  • Page 535

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx i-1 index a access code -------------------------------------------------434 activate a flight plan --------------------------------------212 active channel ----------------------------------------------465 active database --------...

  • Page 536

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A i-2 index datalink receiver troubleshooting -----------------------476 data report--------------------------------------------------- 29 data reports ----------------------------------- 460, 461, 462 date and time -----------------...

  • Page 537

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx i-3 index indicated altitude ------------------------------------------243 initialization (system) --------------------------------------- 11 intersection information --------------------------------------- 172–173 inverting a flig...

  • Page 538

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A i-4 index register ----------------------------------------------- 432, 434 report transmissions --------------------------------------460 required vertical speed -------------------------------------------268 vertical speed indica...

  • Page 539

    190-01255-00 rev. A garmin g1000h ™ pilot’s guide for the bell 407gx i-5 index v vertical deviation guidance ------------------------------229 vertical deviation indicator (vdi) -------------55, 268, 269 vertical navigation -----------------------------------------228 direct-to ---------------------...

  • Page 540

    Garmin g1000h ™ pilot’s guide for the bell 407gx 190-01255-00 rev. A i-6 index b lank p age.

  • Page 542

    Garmin international, inc. 1200 east 151st street olathe, ks 66062, u.S.A. P:913.397.8200 f:913.397.8282 www.Garmin.Com garmin at, inc. 2345 turner road se salem, or 97302, u.S.A. P:503.391.3411 f:503.364.2138 garmin (europe) ltd. Liberty house, bulls copse road houndsdown business park southampton,...