Gpsmap ® 2006/2010 & gps 17 installation instructions.
2 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 all rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or stored in any storage medium, for any purpose without the express prior written consent of g...
3 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 i ntroduction the gpsmap 2006c/2010c multi-function display (mfd) and gps 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fastener...
4 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 i nstallation i nstructions surface mount tools • drill and drill bit • screwdriver • pencil • mounting hardware (not included) note: mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter. To install the ba...
5 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 flush mount tools • flush mount template • jig saw • masking tape • scissors • drill • drill bits—1/8" (3 mm) and 3/8" (6 mm) • 1/16" (2 mm) allen (hex) wrench • sockets or wrenches • hammer • center punch to flush mount the gpsmap 2006c/2010c...
6 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 radar above - best below - ok emi ss jayhaw k good better best 3' vhf radio antenna radar emi (electromagnetic interference) from engine components signal interference note: mount the antenna at least 3 ft away from (preferably above) the pat...
7 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 to attach the enclosed pole mount to the gps 17: 1. Thread the cable though the pole mount. 2. Align the tab on the mount to the notch on the gps 17. 3. Use the enclosed screws to secure the mount to the base. Attaching the pole mount to the ...
8 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 wiring there are two wiring diagrams provided for you convenience. The first is a simple hook-up showing the gpsmap 2006/2010 (using the 18- pin wiring harness), the gps 17 and the alarm circuit. The alarm does not have to be wired for the uni...
9 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 ship's battery 10-32 volts + - garmin gsd 20 sounder module (see gsd 20 install instructions) 4. A garmin sounder unit (other than gsd 20) can provide water depth, water tempature, and speed via nmea data for display on the gpsmap 2006/2010. ...
10 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 final wiring connection once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the gpsmap 2006/2010. The 5-pin port on the right side is intended for future interfacing features and does not req...
11 i nstallation i nstructions gpsmap 2006c/2010c & gps 17 dill this 3/4” or 19 mm hole if the coax is going to be installed through the mounting panel drill using a 11/64” or 4.5 mm drill bit f lush m ount d rilling t emplate.
© copyright 2005 garmin ltd. Or its subsidiaries garmin international, inc. 1200 east 151 st street, olathe, kansas 66062, u.S.A. Garmin (europe) ltd. Unit 5, the quadrangle, abbey park industrial estate, romsey, so51 9dl, u.K. Garmin corporation no. 68, jangshu 2 nd road, shijr, taipei county, taiw...
