Gmr 20/40 marine radar installation instructions.
November 2005 part number 190-00457-02 rev. C printed in taiwan © copyright 2004, 2005 garmin ltd. Or its subsidiaries all rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, fo...
Gmr 20/40 radar installation instructions 1 serial number: w elcome thank you for choosing the garmin gmr 20/40. The gmr 20/40 utilizes the performance of garmin radar and provides overlay and color information when combined with a marine multi-function display (mfd). Contact garmin if you should en...
2 scanner installation the following section covers the installation and setup of the gmr 20 (2 kw) and gmr 40 (4 kw) marine radars. The gmr 20 and 40 only operate with components of the garmin marine network with compatible mfd (mulit-function displays). See your garmin dealer or the garmin web sit...
Gmr 20/40 radar installation instructions 3 mounting the scanner 1. Once a suitable mounting location has been determined, verify that the mounting hole locations are aligned fore and aft, then drill four 9.5 mm (0.37") mounting holes referencing figure 1 below. (this step is not necessary if you ar...
4 gmr 20/40 radar installation instructions final wiring connections once the scanner is installed and the cable routed, you are ready to connect the power, ground and marine network. 1. Connect the black ground (-) wire to the vessel’s negative power terminal. 2. Connect the power (+) wire (with fu...
Gmr 20/40 radar installation instructions 5 powering on the system to power on the scanner: 1. On the mfd (multi-function display), press the red power key. The scanner is automatically powered on with the mfd. The welcome page appears showing the gmr 20 or gmr 40 as a detected network connection. 2...
6 gmr 20/40 radar installation instructions specifications unit dimensions: 28” (710 mm) d x 8” (205 mm) h radar scanner weight: unit 26 lbs; cable 8.35 lbs range scales (range rings): gmr 40 — 1/8 nm (1/32 nm) to 36 nm (9 nm) gmr 20 — 1/8 nm (1/32 nm) to 24 nm (6 nm) power output: gmr 20: 2 kw / gmr...
Gmr 20/40 radar installation instructions 7 towards bow towards stern 28" (710.0 mm) 8.40" (213.5 mm) 5.57" (141.5 mm) 13.97" (355.0 mm) 8" (205.4 mm) 9.17" (233.0 mm).
8 gmr 20/40 radar installation instructions warning and cautions caution: use the gmr 20/40 at your own risk. To reduce the risk of unsafe operation, carefully review and understand all aspects of this owner’s manual, and thoroughly practice operation using the simulator mode prior to actual use. Wh...
Gmr 20/40 radar installation instructions 9 software license agreement by using the gmr 20/40, you agree to be bound by the terms and conditions of the following software license agreement. Please read this agreement carefully. Garmin grants you a limited license to use the software embedded in this...
10 gmr 20/40 radar installation instructions issued: 19/04/2004 revised: 24/08/2005 page: 1 of 1 declaration of conformity application of council directive: 1999/5/ec standard to which conformity is declared: iec 60945 marine navigational equipment – general requirements iec 62252 maritime navigatio...
© copyright 2004, 2005 garmin ltd. Or its subsidiaries garmin international, inc. 1200 e 151st street, olathe, kansas 66062 u.S.A. Tel. 913/397.8200 fax. 913/397.8282 garmin (europe) ltd. Unit 5, the quadrangle, abbey park industrial estate, romsey, so51 9aq u.K. Tel. 44/0870.8501241 fax. 44/0870.85...
